• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.1-8
• /
• 2015

In this paper, a double-input single-output architecture of a LNA(Low Noise Amplifier) is presented to enable to be devised for light weight and small-sized OTM(On-The-Move) satellite communication system suitable to be mounted on vehicles. In spite of advantages of the double-input single-output architecture of a LNA such as reduction of the number of physical channels, it results in time-varying phase error between a fundamental mode path and a high-order mode path. This paper shows that the error can be corrected by adding pilot signals to the LNA and using signal processing, and also gives the measurement data to use the method mentioned above.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.130-138
• /
• 2015

Despite of recently strengthened vehicle emission regulations, NOx emissions are not decreased in urban areas because of discrepancies between certification emission test modes and real driving conditions. Thus, researches on RDE-LDV (Real-driving Emission-Light-duty Vehicle) have been conducted actively using PEMS (Portable Emissions Measurement Systems). In the present study, NOx emissions were measured for 5 Korean light duty vehicles for real driving conditions including city, combined, highway, and up-downhill test route. Emission characteristics were analyzed for averaged NOx emissions per unit driving distance of each driving test routes. Furthermore, MAW (Moving Average Window) method based on $CO_2$ emissions from WLTC, which will be supported for EU regulations, was utilized. It was revealed that DRs (deviation ratios) for diesel vehicles (i.e., 5.1 ~ 8.4) were greater than gasoline vehicles (less than 0.15). Especially DR of diesel vehicle for up-downhill test route was 8.4, which indicates severe NOx emissions.

• Smart Media Journal
• /
• v.6 no.3
• /
• pp.15-20
• /
• 2017

Recently, the automotive industry has been studied about driver assistance systems for helping drivers to drive their cars easily by integrating them with the IT technology. This study suggests a method of detecting lanes, robust to road condition changes and applicable to lane departure warning and autonomous vehicles mode. The proposed method uses the method of detecting candidate areas by using the Gaussian filter and by determining the Otsu threshold value and edge. Moreover, the proposed method uses lane gradient and width information through the Hough transform to detect lanes. The method uses road lane information detected before to detect dashed lines as well as solid lines, calculates routes in which the lanes will be located in the next frame to draw virtual lanes. The proposed algorithm was identified to be able to detect lanes in both dashed- and solid-line situations, and implement real-time processing where applied to Raspberry Pi 2 which is open source hardware.

• The Journal of the Convergence on Culture Technology
• /
• v.5 no.1
• /
• pp.429-434
• /
• 2019

There are several high technologies applied to the driving cars such as self-driving car and connected car for safe and convenient driving. VANET provides useful information such as route selection and gas price by communicating nearby cars and RSUs. VANET prefers CCN rather than traditional TCP/IP stack because CCN offers inherent multicast communication for sharing traffic information as well as traditional unicast. When all participating node rebroadcasts the Interest packets in a Vehicular CCN, the network may suffer from Broadcast Storm Problem. In order to mitigate the effect of the problem and to improve the Data packet transmission, not all but some selected nodes have to rebroadcast the packet. This paper simulates car movements using SUMO and evaluates data transmission performance using ns-3. According to the simulation results, when some selected nodes rebroadcast the Interest packets, the transmission performance improves 10% to 25% depending on the number of requesting nodes.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.7
• /
• pp.849-856
• /
• 2020

Recently, as the number of high-height vehicles such as double-decker buses has increased, collision accidents have occurred in bridges and tunnels due to the deviation from the designated routes and driver's carelessness. In the case of the existing front collision warning system, it is limited to vehicles and pedestrians, so it is difficult to use it as a pass height warning system for the high height vehicles. In this paper, we propose a system that generates a warning by determining the correlation and time series characteristics of data for each segment using multiple lidar sensors and then determining the possibility of collision in the upper part of the vehicle. Also, the proposed system confirmed the proper operation through a real-time driving test and a system performance evaluation by the Korea Automobile Testing & Research Institute.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.1
• /
• pp.17-34
• /
• 2022

This paper develops a model for dynamic station assignment to optimize the Demand Responsive Transit (DRT) operation. In the process of optimization, we use the bus travel time as a variable for DRT management. In addition, walking time, waiting time, and delay due to detour to take other passengers (detour time) are added as optimization variables and entered for each DRT passenger. Based on a network around Anaheim, California, reserved origins and destinations of passengers are assigned to each demand responsive bus, using K-means clustering. We create a model for selecting the dynamic station and bus route and use Non-dominated Sorting Genetic Algorithm-III to analyze seven scenarios composed combination of the variables. The result of the study concluded that if the DRT operation is optimized for the DRT management, then the bus travel time and waiting time should be considered in the optimization. Moreover, it was concluded that the bus travel time, walking time, and detour time are required for the passenger.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5D
• /
• pp.731-738
• /
• 2006

Facing congestion, people want to know traffic information about their routes, especially real-time link travel time (LTT). In this paper, as a sequel paper of the previous non-taxi based LTT generating study by Choi et al. (1998), taxi based GPS probes have been tried to produce LTT for urban arterials. Taxis in itself are good deployment mode of GPS probes although it by nature experiences boarding and alighting time noises which should be accounted. A heuristic real-time dynamic outlier filter algorithm for taxi GPS probe has been developed focusing on urban arterials. An actual traffic survey for dynamic link travel times has been conducted using license plate method for the test arterials of Seoul city transportation network. With the algorithm, it is estimated that 70% of outliers have been filtered and the relative error has been improved by 73.7%. The filtering algorithm developed here would be expected to be in use for other spatial sites with some calibration efforts. Some limitations and future research agenda have also been discussed.

• Journal of the Korea Society for Simulation
• /
• v.17 no.2
• /
• pp.91-103
• /
• 2008

In order to simulate the behavior of automated manufacturing systems, the performance of material handling systems should be measured dynamically. Multi-Agent technology could be well adapted for the development of simulator for distributed and intelligent manufacture systems. A multi-agent system is composed of one coordination agent and multiple application agents. Issues in AGVS simulator can be classified by the set-up and operating problems. Decisions on the number of vehicles, bi- or uni-directional guide-path, etc. are fallen into the set-up problem category, while deadlock tree algorithm and conflict resolution are in operating problem. In this paper, a multi-agent based deadlock-free simulator for automated guided vehicle system(AGVS) are proposed through the use of multi-agent technologies and the development of deadlock-free algorithm. In this AGVS simulator proposed, well-known Floyd algorithm is used to create AGVS Guide path, through which AGVS move. Also, AGVs avoid vehicle conflict and deadlock using check path algorithm. And Moving vehicle agents are operated in real-time control by coordination agent. AGV position is dynamically calculated based on the concept of rolling time horizon. Simulator receives and presents operating information of vehicle in AGVS Gaunt chart. The performance of the proposed algorithm and developed simulator based on multi-agent are validated through set of experiments.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1216-1221
• /
• 2022

Ships tend to be larger to increase the efficiency of cargo transportation. Larger ships lead to increased travel time for ship workers, increased work intensity, and reduced work efficiency. Problems such as increased work intensity are reducing the influx of young people into labor, along with the phenomenon of avoidance of high intensity labor by the younger generation. In addition, the rapid aging of the population and decrease in the young labor force aggravate the labor shortage problem in the maritime industry. To overcome this, the maritime industry has recently introduced technologies such as an intelligent production design platform and a smart production operation management system, and a smart autonomous logistics system in one of these technologies. The smart autonomous logistics system is a technology that delivers various goods using intelligent mobile robots, and enables the robot to drive itself by using sensors such as lidar and camera. Therefore, in this paper, it was checked whether the mobile robot could autonomously drive to the stop sign by detecting the passage way of the ship deck. The autonomous driving was performed by detecting the passage way of the ship deck through the camera mounted on the mobile robot based on the data learned through Nvidia's End-to-end learning. The mobile robot was stopped by checking the stop sign using SSD MobileNetV2. The experiment was repeated five times in which the mobile robot autonomously drives to the stop sign without deviation from the ship deck passage way at a distance of about 70m. As a result of the experiment, it was confirmed that the mobile robot was driven without deviation from passage way. If the smart autonomous logistics system to which this result is applied is used in the marine industry, it is thought that the stability, reduction of labor force, and work efficiency will be improved when workers work.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.347-352
• /
• 2012

In this paper, an 2D spatial-map construction for workers identification and avoidance of AGV using the detection scheme of the spatial coordinates based on stereo camera is proposed. In the proposed system, face area of a moving person is detected from a left image among the stereo image pairs by using the YCbCr color model and its center coordinates are computed by using the centroid method and then using these data, the stereo camera embedded on the mobile robot can be controlled for tracking the moving target in real-time. Moreover, using the disparity map obtained from the left and right images captured by the tracking-controlled stereo camera system and the perspective transformation between a 3-D scene and an image plane, depth map can be detected. From some experiments on AGV driving with 240 frames of the stereo images, it is analyzed that error ratio between the calculated and measured values of the worker's width is found to be very low value of 2.19% and 1.52% on average.