• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.373-374
• /
• 2007

지중배전관로공사 설계시 고려할 사항은 지중배전관로 공수산정, 적정관로 선정, 매설위치 및 매설깊이, 관재의 선정, 관로의 경간, 관로배열 등이 고려되어야 한다. 관로공사비는 굴착깊이와 굴착폭에 의해 산정되고 이는 관로배열, 굴착지반의 토질에 따른 굴착구배, 용수여부, 도로관리기관의 조례, 다짐정도, 작업환경, 작업시간 등에 의해 변화하게 된다. 이런 현장조건 들은 설계자가 바꿀 수 없는 요소이지만 관로배열을 어떤 형태로 하여 매설할지는 설계자가 정하여야 한다. 본 연구에서는 경제적인 관로배열을 선정하기 위해 관로공수별, 관로유형별 공사비를 산출하여 비교 검토하였고 현장에서의 공사시공성, 케이블의 허용전류 등을 종합적으로 고려하여 최적의 관로배열을 제시하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1541-1545
• /
• 2009

홍수 기간 중 부유잡목에 의한 수위상승 원인은 크게 상류부에서 이송되어진 유송잡물에 의한 교량 등의 수공구조물에 집적으로 인한 통수능 부족에 의하여 발생되는 수위상승과 하천내 수공 구조물의 부적절한 설계 및 시공으로 인한 수위상승으로 구분되어 진다. 현재 교량의 여유고 산정에 사용되는 홍수위는 통수능을 고려하지 않은, 하천정비계획에 사용되는 홍수위를 적용하고 있으며, 다만 통수능의 확보를 위하여 경간장에 대한 제한을 두고 있을 뿐이다. 중소하천에 위치하는 교량의 경우, 여유고 확보에 대한 기준을 적용함에 있어서 교량이 위치한 하천 단면에서의 통수능의 영향이 고려되어야 유수의 월류에 대한 위험성을 줄일 수 있다. 더욱이 하천설계기준(2005)에서는 고정 홍수량에 의한 여유고 산정치를 제안하고 있을 뿐이기 때문에, 하천설계기준에서 교량과 관련된 여유고도 하상변동과 만곡부에 의한 수위 상승, 유송잡물에 의한 통수능 영향, 계산오차 등을 고려하여 충분한 여유고를 확보하도록 보완할 필요가 있다. 본 연구에서는 부유잡목에 의한 수위상승 원인을 분석을 하고, 이에 따른 수리모형실험을 통하여 부유잡목의 높이/폭(H/B)변화에 의한 수위상승, 부유잡목의 형태별 수위상승, 교각사이 개도비에 따른 수위 상승량을 산정하여 기존의 여유고에 대한 추가적인 여유고를 확보하여 홍수시 통수능을 확보하고자 하였다. 부유잡목의 형태에 따른 수위상승량을 산정하기 위하여 개도비를 70%로 고정한 후, Fr수를 변화시켜 부유잡목의 높이/폭(H/B) 형태에 따라 산정한 결과, 부유잡목이 존재하지 않는 상태에 비하여 부유잡목에 의한 영향으로 인한 수위증가율이 Fr값이 클수록 더욱 크게 나타났으며, 부유잡목이 동일면적인 경우 폭(B)에 비하여 높이(H)가 커질수록 수위 상승이 크게 나타났다. 또한, Fr수 변화에 따른 최고수위 상승율을 구하였을 때, 상류조건에서 Fr < 0.5 인 경우는 기존 여유고에 대하여 최대 10%의 여유고를 추가 확보하며, 0.5 < Fr < 1 인 경우는 기존 여유고에 대하여 최대 20%의 여유고를 추가 확보하도록 설계하는 것이 바람직하다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.3
• /
• pp.269-275
• /
• 2016

In this paper, shear performance of concrete wide beams was evaluated through shear failure tests. The specimens were designed to have two continuous spans with a column at the center of the wide beam. Also the specimens were reinforced with plates with openings as shear reinforcements. For the test, total eight specimens, including five specimens were reinforced with steel plates and the other three specimens were reinforced with GFRP plates were manufactured. And the shear strengths obtained from the tests were compared with ones from the equation provided by ACI 318. Support width of wide beam, support section of wide beam and shear reinforcement material were considered as variables. The results showed that the support width was proportional to the increase of shear strength. Also, regardless of material type of shear reinforcement, the shear reinforcing effect was similar when the amount of shear reinforcement was the same.

• Journal of Bio-Environment Control
• /
• v.7 no.4
• /
• pp.290-297
• /
• 1998

In this study an optimization of greenhouse roof shape was performed to maximize solar light transmission which is one of the most important elements in greenhouse environment. To determine roof shape that maximize the total light transmissivity, a computer model for analysing light transmissivity was composed and the Genetic Algorithms was applied for solving optimization problems. By setting composite model as objective function(fitness function), the optimum combination of design variables(roof inclination angle, width ratio) was searched using Genetic Algorithms. The optimum combination of input variables for the maximum light transmissivity at Suwon in winter was found 40 degree root angle , 0.5 width ratio, for two span greenhouses and 37 $_。 / roof angle, 0.7 width ratio, for single span greenhouses.es.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.259-269
• /
• 2005

This paper describes the application of genetic algorithm for the discrete optimum design of reinforced concrete continuous beams. The objective is to minimize the total cost of reinforced concrete beams including the costs of concrete, form work, main reinforcement and stirrup. The flexural and shear strength, deflection, crack, spacing of reinforcement, concrete cover, upper-lower bounds on main reinforcement, beam width-depth ratio and anchorage for main reinforcement are considered as the constraints. The width and effective depth of beam and steel area are taken as design variables, and those are selected among the discrete design space which is composed with dimensions and steel area being used from in practice. Optimum result obtained from GA is compared with other literature to verify the validity of GA. To show the applicability and efficiency of GA, it is applied to three and five span reinforced concrete beams satisfying with the Korean standard specifications.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.241-256
• /
• 2010

This study intends to develop an aerodynamic girder for suspension bridge with width corresponding to 1/70 of the main span length. In the first step of present study, parametric study for the effects of major structural properties on aerodynamic stability of bridges was performed. The span length and natural frequency of bridges were found to be free from girder width, girder height, and aspect ratio of width to height. The empirical equation according to confidence interval was proposed to estimate the natural frequencies of bridges from span length. From the sensitivity analysis, it was revealed that the torsional frequency was dominant parameter among various structural properties that affected flutter velocity mostly. The final aerodynamic bridge section which satisfied the flutter criteria was found from section wind tunnel tests for 30 cross sectional models. The aerodynamic stability of the developed cross section was verified by multimode flutter analysis. The present economical cross section can be used for long span suspension bridge.

• Journal of the Korea Concrete Institute
• /
• v.19 no.2
• /
• pp.171-178
• /
• 2007

Twelve reinforced concrete continuous deep beams having web openings within interior shear spans were tested to failure. All beams tested had the same geometrical dimensions. The main variables investigated were the opening size and amount of inclined reinforcement around openings. An effective inclined reinforcement factor combining the influence of the opening size and amount of inclined reinforcement on the structural behavior of the beams tested is proposed. It was observed that the load distribution, diagonal crack width, and load capacity of beams tested were greatly dependent on the effective inclined reinforcement factor which ranged from 0 to 0.171 for the test specimens. The higher this factor, the smaller the diagonal crack width and its development rate. A higher load capacity also developed in beams having effective inclined reinforcement factor above 0.077 than in the corresponding solid deep beams. A numerical technique based on the upper bound analysis of the plasticity theory is proposed to evaluate the load capacity of continuous deep beams having openings within interior shear spans. Predictions obtained from the proposed formulas are in good agreement with test results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1707-1721
• /
• 2014

Half-depth panels were developed with the merits of CIP (Cast In Place) decks and precast decks for constructability and fast construction. In this paper, details of half-depth panels with pre-tensioning were suggested. For evaluation of structural performance, five half-depth panel specimens were fabricated and static tests were conducted. The cross-sections of these specimens were composed of pre-tensioned half-depth panels and pre-tensioned two-span half-depth panels. Test parameters were the amount of the prestressing force and the longitudinal reinforcements. Static tests on simply-supported slabs showed that ultimate strength was 1.55 times greater than calculated nominal strength. The flexural strength was only 10 % increased and the influence on crack width control was negligible when the member of tendons was increased twice. For two-span continuous specimens, the ultimate strength increased 1.2 times and 1.38 times respectively as the reinforcement was additionally provided. The verified half-depth panels by this research can be effectively utilized for the fast replacement or construction of bridges.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.3 s.49
• /
• pp.113-123
• /
• 2006

An experimental investigation on the behavior of reinforced concrete coupling beams is presented. The test variables are the span-to-depth ratio, the ratio of flexural reinforcements and the ratio of shear rebars. The distribution of arch action and truss action which compose the mechanism of shear resistance is discussed. The increase of plastic deformation after yielding transforms the shear transfer by arch action into by truss action. This study proposes the deformation model for reinforced concrete coupling beams considering the bond slip of flexural reinforcement. The strain distribution model of shear reinforcements and flexural reinforcements based on test results is presented. The yielding of flexural reinforcements determines yielding states and the ultimate states of reinforced concrete coupling beam are defined as the ultimate compressive strain of struts and the degradation of compressive strength due to principal tensile strain of struts. The flexural-shear failure mechanism determines the ultimate state of RC coupling beams. It is expected that this model can be applied to displacement-based design methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.04a
• /
• pp.33-40
• /
• 2004

본 논문에서는 한국과 일본에 위치한 여러 연구기관들 사이에서 수행된 온라인 네트워크 유사동적 실험결과에 대해 나타내었다. 예제 구조물로는 4경간 연속의 면진 교량을 이용하였다. 실험 장비를 보유하고있는 두 연구기관에서 면진 장치의 비선형 거동에 대한 실험을 수행하고 각 실험 결과를 조합하여 전체구조의 동적 해석을 수행하였다. 본 논문에서는 먼저 인터넷을 이용한 두 가지 데이터 전송기법을 이용하여 두 기법의 효율성을 비교, 분석하였다. 또한 최근 국내에 위치한 두 연구기관 사이에서 수행된 실험 결과에 대해 논의하였다. 마지막으로 유선과 무선 인터넷을 이용한 온라인 실험 기법에 대하여 나타내었다. 그 결과, 온라인 네트워크 실험에 소요된 실험 시간은 데이터 전송 기법과 실험장비에 따라 매 시간 단계의 데이터 전송에 0.2-15초, 각 연구기관의 유사동적 실험에 1-10초의 시간이 소요되어 매우 큰 폭으로 변화함을 알 수 있었다. 또한 무선 인터넷을 이용한 온라인 실험의 경우, 뛰어난 이동성과 인터넷 보안성 등과 같은 여러 가지 장점을 가지고 있음을 알 수 있었다.