• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.5
• /
• pp.130-135
• /
• 2013

Anti-icing system can reduce traffic accidents and congestion by quickly removing the frozen road surface area. there is no decision criteria for determining application of the Anti-icing system in Korea. In this study, we proposed the decision criteria for determining application of the anti-icing system based on weather and road conditions, i.e., geometric and topographic conditions. Regional climate survey, Solar Radiation analysis, and dynamic vehicle simulation considered road geometry was conducted to standardize the installation method of anti-icing system. Also, we have developed a software that can be determined an installation of anti-icing system.

• Magazine of korean Tunnelling and Underground Space Association
• /
• v.4 no.1
• /
• pp.54-61
• /
• 2002

• The Journal of the Korea Contents Association
• /
• v.11 no.11
• /
• pp.42-48
• /
• 2011

This paper presents a bridge road surface frost prediction and monitoring system. The node sensing hardware comprises microprocessor, temperature sensors, humidity sensors and Zigbee wireless communication. A software interface is implemented the control center to monitor and acquire the temperature and humidity data of bridge road surface. A bridge road surface frost occurs when the bridge deck temperature drops below the dew point and the freezing point. Measurement data was used for prediction of road surface frost occurrences. The actual alert is performed at least 30 minutes in advance the road surface frost. The road surface frost occurrences data are sent to nearby drivers for traffic accidents prevention purposes.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.6
• /
• pp.19-25
• /
• 2016

Anti-icing is important in gas turbines because ice formation on compressor inlet components, especially inlet guide vane, can cause performance degradation and mechanical damages. In general, the compressor bleeding anti-icing system that supplies hot air extracted from the compressor discharge to the engine intake has been used. However, this scheme causes considerable performance drop of gas turbines. A new method is proposed in this study for the anti-icing in combined cycle power plants(CCPP). It is a heat exchange heating method, which utilizes heat sources from the heat recovery steam generator(HRSG). We selected several options for the heat sources such as steam, hot water and exhaust gas. Performance reductions of the CCPP by the various options as well as the usual compressor bleeding method were comparatively analyzed. The results show that the heat exchange heating system would cause a lower performance decrease than the compressor bleeding anti-icing system. Especially, the option of using low pressure hot water is expected to provide the lowest performance reduction.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2256-2261
• /
• 2008

The electric snow melting and deicing system by electric heating cable which is adopted in this study is a part of road facilities to keep surface temperature of the road higher than freezing point of water for melting the snow or ice accumulated on it. The electric heating cables are buried under paved road at a certain depth and a certain pitch and operated automatically and manually. Design theory, amount of heating, and installation standard vary according to economic situation, weather condition, and installation place. A main purpose of this study is figuring out the appropriate range of required heat capacity and installation depth and pitches for solving snowdrifts and freezing problems with minimum electric power consumption. This study was performed under the ambient air temperature($-2^{\circ}C$, $-5^{\circ}C$), the pitches of the electric heating cables (200 mm, 300 mm), heating value ($250\;W/m^2$, $300\;W/m^2$, $350\;W/m^2$).

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.117-117
• /
• 2007

• Journal of the Korean Society of Safety
• /
• v.8 no.4
• /
• pp.139-148
• /
• 1993

Thermosyphons are simple devices that can passively transport thermal energy over relatively long distance with little temperature degradation. These attributes permit the use of low grade thermal energy for thermal control of structures including the snow melting and deicing to the pavement surface. The thermosyphon system requires no costly energy input and Is completely maintenance free. This paper presents the experimental results of the snow melting system in which thermosyphon was utilized to transfer the geothermal energy to the pavement to obviate slipping traffic accidents due to freezing of pavement in winter.

• 한국도로학회지:도로
• /
• v.15 no.2
• /
• pp.57-61
• /
• 2013

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.4
• /
• pp.31-38
• /
• 2019

Field tests with carbon fiber heating wire (CFHW) embedded inside concrete slab were performed to present the alternative heating material capable of avoid the adverse effects of traditional de-freezing salt on the structures and environment. The CFHW was inserted into the concrete slab in the shape of 'ㄷ' to improve the heat superposition and the temperature on the surface was measured using iButton. The results showed that the temperature where the CFHW's were faced with each other increased to above zero after 12-hour at outdoor air temperature of $-6^{\circ}C$. Comparatively, the temperature slightly increased where the CFHW was embedded on one side because the heat was not superimposed. Hence, it can be said that the CFHW is a suitable heating material to prevent the concrete road from being frozen.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.103-110
• /
• 2022

Degradation of handling qualities(HQs) due to bad weather or mechanical failure can pose a fatal risk to pilots unfamiliar with such situation. In particular, icing is an important issue to consider as it is a frequent cause of accidents. Most of the previous research works focuses on aerodynamic performance changes due to icing and the corresponding icing modeling or methods to prevent icing, whereas the present work attempts to actively compensate for HQ degradation due to icing on a full-scale helicopter through flight control law design. To this end, the present work first demonstrates HQ degradation due to icing using CONDUIT software, and subsequently presents a robust control design via the RS-LQR(Robust Servomechanism Linear Quadratic Regulation) procedure to compensate for the HQ degradation. Simulation results show that the proposed robust control maintains Level 1 HQ in the presence of icing.