• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2011.04a
• /
• pp.340-344
• /
• 2011

건축물 마감재료의 연소시 발생되는 독성가스는 대형화재로 인한 인명피해의 주된 원인 중의 하나이다. 현행 건축법에서는 건축물마감재료에 대하여 동물의 평균행동정지시간을 측정하는 가스유해성시험을 실시하고 있다. 본 연구는 동물시험이 아닌 NFPA 269에 의한 유효량분율(FED: Fractional effective does)을 이용하여 건축물 마감재의 독성지수를 도출하였다. 현행 가스유해성 평가 방법에서 사용되는 채임버(피검상자)를 이용하여 적외선분광분석 및 산소분석기로 연소가스를 정량 분석하였으며, NFPA269에서 규정하는 FED를 도출하였다. 몇 가지 건축재료에 대한 가스유해성시험의 평균행동정지시간과 FED의 상대적인 비교를 통해 연소가스독성평가를 수행하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.30-38
• /
• 2023

As the number of old buildings subject to safety inspection increases, the burden on designated institutions and management entities that are responsible for safety management is increasing. Accordingly, when selecting buildings subject to safety inspection, appropriate safety inspection standards and appropriate technology are essential. The current safety inspection standards for old buildings give low scores when it is difficult to confirm damage such as cracks in structural members due to finishing materials. This causes the evaluation results to be underestimated regardless of the actual safety status of the structure, resulting in an increase in the number of aging buildings subject to safety inspection. Accordingly, this study proposed a thermal imaging technique, a non-destructive and non-contact inspection, to detect cracks inside finishing materials. A concrete specimen was produced to observe cracks inside the finishing material using a thermal imaging camera, and thermal image data was measured by exciting a heat source on the concrete surface and cracked area. As a result of the measurement, it was confirmed that it was possible to observe cracks inside the finishing material with a width of 0.3mm, 0.5mm, and 0.7mm, but it was difficult to determine the cracks due to uneven temperature distribution due to surface peeling and peeling of the wallpaper. Accordingly, as a result of performing data analysis by deriving the amplitude and phase difference of the thermal image data, clear crack measurement was possible for 0.5mm and 0.7mm cracks. Based on this study, we hope to increase the efficiency of field application and analysis through the development of technology using big data-based deep learning in the diagnosis of internal crack damage in finishing materials.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.343-359
• /
• 2017

Many researches and policies have been carried out for saving energy in buildings. However, there are a few studies of thermal characteristics of wood-based materials that have been widely used as structural materials and finishing materials in buildings. In this study, thermal bridging areas were found to investigate thermal performance of residential building using non wood-based materials and wood-based materials. And heat transfer analysis of 16 case studies according to composition of structural materials and finishing materials was conducted. Also in this experiment, Physibel Trisco was used as the heat transfer analysis simulation tool, which conforms to the calculation method of ISO 10211. Analytical modeling was also carried out according to the ISO 10211, and the boundary temperature conditions were set at room temperature $20^{\circ}C$ and outdoor temperature $-11.3^{\circ}C$ (Seoul standard) according to the energy saving design standard in South Korea. Applied structures are classified according to the cases of concrete structure with non wood-based finishing materials, concrete structure with wood-based finishing materials and wood structure. Analyzed building elements were divided into a wall, a roof, an interlayer floor and a bottom floor. As a result, it can be confirmed that the thermal bridge of the concrete structure and wood structure were caused by the geometrical and material causes. In addition, the structural thermal bridge was caused in the discontinuity of the insulation in the concrete structure. Also it was confirmed that the linear heat transfer coefficient of the wall decreases when the wood-based materials are applied to the concrete structure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.2
• /
• pp.143-152
• /
• 2006

High performance concrete(HPC) has been widely used in high-rise building. The HPC has several benefits including high strength, high fluidity and high durability. However, spalling is susceptible to occur in HPC and HPC also tends to be deteriorated in the side of fire resistance performance at fire. This paper investigated the spalling prevention of high performance RC column. Control concrete showed severe failure and a case of concrete with fire enduring spraying material exhibited more severe spalling failure than even control concrete. In addition, concrete with fire enduring paint reported the most favorable spalling resistance effect for preventing spall, compared with other concrete covered with finishing materials, such as fire enduring spraying material, gypsum board, marble board and fire enduring PC board. Meanwhile, concrete adding 0.1% of PP fiber demonstrated spalling resistance performance after 3hours load bearing test.

• The Monthly Technology and Standards
• /
• s.30
• /
• pp.38-42
• /
• 2004

• The Journal of the Acoustical Society of Korea
• /
• v.12 no.2
• /
• pp.86-93
• /
• 1993

준공후 10여년동안 사용한 천장 및 벽의 마감재에 대한 전면적인 보수를 실시한 부산 시민회관을 대상으로 보수 전후의 음향특성에 대해 비교 검토하였다. 본 연구에서는 특히 전객석에서의 고른 음압분포와 적절한 잔향시간을 얻기 위한 측면에 주안점을 두고 보수설계를 하였으며 보수 작업시 사전에 음향특성을 측정 분석한 후 이를 근거로 용도에 맞는 음향성능을 발휘할 수 있도록 마감재의 선정 및 배치를 하여 건축설계에 반영하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.1
• /
• pp.32-38
• /
• 2024

In the case of apartment building, it is difficult to conduct non-destructive testing due to the actual presence of people and the dust and noise generated during the core test, so inspections are performed each time in the common area and underground parking lot, and the tests are conducted on the finishing material rather than on the concrete surface due to low-cost orders. As the process progresses, poor inspection is inevitable. In addition, the proposed formulas for strength estimation have large fluctuations depending on the differences in test conditions and environments, and even if they show the same measured value, the deviation between each proposed formula is large, making it difficult to accurately estimate strength, making it difficult to use. Accordingly, we would like to select finishing materials mainly used in apartment complexes and compare and evaluate the compressive strength of concrete according to the type of finishing material by using non-destructive testing methods directly on the finishing materials without removing the finishing materials. The reliability evaluation results of the estimated compressive strength of concrete using the ultrasonic velocity method according to the type of finishing material are as follows. The error rate between the estimated compressive strength and compressive strength derived through the ultrasonic velocity method shows a wide range of variation, ranging from 21.83% to 58.89%. The effect of the presence or absence of finishing materials on the estimated compressive strength was found to be insignificant. Accordingly, it is necessary to select more types of finishing materials and study ultrasonic velocity methods according to the presence or absence of finishing materials, and to study estimation techniques that can increase reliability.

• The magazine of the Korean Society for Advanced Composite Structures
• /
• v.5 no.4
• /
• pp.21-28
• /
• 2014

최근 증가하는 현무암 석분슬러지를 건설재료로 재활용하기 위한 방안으로, 시멘트 몰탈에서 잔골재의 일부를 현무암석분슬러지로 대체한 후, 기능성 마감재로서의 성능을 검증한 결과 다음과 같은 결과를 얻었다. 1. 현무암 석분슬러지를 포함한 몰탈의 휨인장강도와 압축강도는, 대체율 21%에 도달할 때까지 압축 및 휨인장강도는 일반 시벤트몰탈 대비 각각 47%와 35% 증가하였다. 2. 원적외선 방사율에 있어서도 기존몰탈보다 높은 0.933까지 이르렀으며, 이 수치는 기타 기능성 마감재보다 우수한 원적외선 방사율을 나타내는 것이다. 3. 음이온 방사량은 현무암석분의 대체율에 따른 일관된 경향을 보이지는 않았으나, 일반 시멘트몰탈 보다는 5% ~ 12% 증가효과가 나타났다. 4. 기존 시멘트몰탈의 잔골재의 21%를 현무암석분슬러지로 대체할 경우, 시멘트 몰탈보다 물리적 성질이 증가 함과 동시에, 기능성몰탈로서의 원적외선 방사율, 음이온 방사량의 증진효과가 있었다. 또한 새로운 건축자재의 생산을 통한 경제적 이득은 물론, 산업폐기물의 양을 줄일 수 있다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.279-282
• /
• 2012

This study attempted to the effect on the physical performance of silane coupling agent on solventless epoxy-based concrete surface finishing material for parking floor. Tests were carried out in accordance with KS F 4041 and KS F 4937. The results of compressive strength, flexural compressive are 95.6N/㎟, 25.4N/㎟ and after wheel moving load testing, average abrasive depth is 0.96mm, these results satisfied the quality standard of KS F 4041, KS F 4937. As conclusion, this study confirmed that the silane coupling agent greatly effected on the physical performance of solventless epoxy resin.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.7-8
• /
• 2017

As the importance of maintenance of reinforced concrete structure recently has emerged, the attention of durability of structure has been increasing. There are many studies about durability decline especially due to the carbonation. In order to study carbonation progress after surface repair of carbonated concrete, each carbonation penetration velocity from different repair materials of concrete structure is compared through the experiment of carbonation accelerating CO₂ concentration to 5%. As carbonation infiltration progress is predicted through this study, the counterplan of service life evaluation will be prepared on selection of repair materials of concrete structure.