• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.78-85
• /
• 2019

This study targets SFRC hollow members with small depth under shear force and bending. To evaluate the effect of web width on shear strength of SFRC members, experiment and finite element analysis were conducted and compared with existing equations. The web width was planned to be 1/2 times and 2/3 times, and the shear span ratio was planned to be 1.5 times. In the shear test results, the maximum shear strength increased by 10.3 to 28.0% with the web width increased by 33%. When the overall depth of specimens was increased by 1.5 times, the shear strength of the specimen with a web width of 100mm was increased by 29.2%. On the other hand, specimen with the 150mm only increased by 11.3%. These results indicate that the smaller the web width, the greater the shear strength increase with the increase of depth. Also, the smaller the web width, the greater the contribution of steel fiber. It has been shown that the KCI code evaluates the shear strength of experiments as very safe side, and that the proposed formula of Shin et al. predicts the experimental strength relatively well. As the web width increases by 2, 3, and 6 times, the mean shear strength by FEA appears to be 1.18, 1.80, and 2.19 times respectively. This indicates that the shear strength does not increase in proportion to the increase in web width.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.5
• /
• pp.329-337
• /
• 2017

In USA and UK, the standards of both reverberation time and background noise level have been established for the appropriate aural environment in classrooms. In order to realize this, guidelines for architectural planning and interior finishing have been also suggested. However, in Korea, there has hardly been any guidelines for satisfying background noise criteria and investigation about sound insulation performance of current walls of classrooms. The present study investigates the structure of outer wall and walls between classrooms of two middle schools in order to analyze the sound insulation performance against both exterior and interior noises. Acoustic parameters including transmission loss, standardized sound level difference, and signal to noise ratio have been measured and analyzed for sound insulation performance of walls and flanking noises. As a result, concerning the walls in between classrooms, it was found that walls of dry construction have greater sound insulation performance rather than the walls of wet construction especially in mid and high frequency bands. Also, It was revealed that thermopane, insulated pair glass, of outer walls, has greater sound insulation performance than the double window consisted of two single pane glass. Regarding flanking noises, the standards were exceeded when all windows, or windows and doors front onto corridor were opened. It denotes that students could be disturbed with the sound transmission by the interior noises.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.94-101
• /
• 2023

In this study, the development performance of the head bars, which is SD700, was experimentally evaluated at the RC (reinforced concrete) or SFRC (steel fiber reinforced concrete external beam-column joint. A total of 10 specimens were tested, and variables such as steel fibers, length of settlement, effective depth of the beam, and stirrups of the column were planned. As a result of the experiment, the specimens showed side-face blowout, concrete breakout, and shear failure depending on the experimental variables. In the RC series experiments with development length as a variable, it was confirmed that the development strength increased by 26.5~42.2% as the development length increased by 25-80%, which was not proportional to the development length. JD-based experiments with twice the effective depth of beams showed concrete breakout failure, reducing the maximum strength by 31.5% to 62% compared to the reference experiment. The S-series experiment, in which the spacing of the shear reinforcement around the enlarged head reinforcement was 1/2 times that of the reference experiment, increased the maximum strength by 8.4 to 9.7%. The concrete compressive strength of SFRC was evaluated to be 29.3% smaller than the concrete compressive strength of RC, but the development strength of SFRC specimens increased by 7.3% to 12.2%. Accordingly it was confirmed that the development performance of the head bar was greatly improved by reinforcing the steel fiber. Considering the results of 92% and 99% of the experimental maximum strength of the experiment arranged with 92% and 110% of the KDS-based settlement length, it is judged that the safety rate needs to be considered even more. In addition, it is required to present a design formula that considers the effective depth of the beam compared to the development length.

• Journal of Korean Association for Spatial Structures
• /
• v.4 no.2 s.12
• /
• pp.89-97
• /
• 2004

The objective of this study is the development of a scheme and discrete optimum design algorithm, which is based on the genetic algorithm. The algorithm can perform both scheme and size optimum designs of plane trusses. The developed Scheme genetic algorithm was implemented in a computer program. For the optimum design, the objective function is the weight of structures and the constraints are limits on loads and serviceability. The basic search method for the optimum design is the genetic algorithm. The algorithm is known to be very efficient for the discrete optimization. However, its application to the complicated structures has been limited because of the extreme time need for a number of structural analyses. This study solves the problem by introducing the size & scheme genetic algorithm operators into the genetic algorithm. The genetic process virtually takes no time. However, the evolutionary process requires a tremendous amount of time for a number of structural analyses. Therefore, the application of the genetic algorithm to the complicated structures is extremely difficult, if not impossible. The scheme genetic algorithm operators was introduced to overcome the problem and to complement the evolutionary process. It is very efficient in the approximate analyses and scheme and size optimization of plane trusses structures and considerably reduces structural analysis time. Scheme and size discrete optimum combined into the genetic algorithm is what makes the practical discrete optimum design of plane fusses structures possible. The efficiency and validity of the developed discrete optimum design algorithm was verified by applying the algorithm to various optimum design examples: plane pratt, howe and warren truss.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.4
• /
• pp.119-129
• /
• 2009

Building construction trends have been changed dramatically in terms of size and mass. With the need to maximize land usage, there has been an increase in the construction of high-rise buildings. This affects not only the entire construction duration and cost, but also subsequent construction activities, such as work to increase underground facilities and in reclamation land area construction. These types of site conditions require soft ground reinforcement and the proper uplift water pressure treatment. In general, two kinds of methods have been used for uplift water pressure treatment systems. However, there have been some problems arising as the result of a lack of research and analysis on underground construction techniques, and a reliance on experiments over actual survey and analysis of site conditions. This paper focused on the problems of conventional selection procedure, by analyzing drawings and proposing a kind of modeling for a reasonable procedure. The results were applied to OO project as a sample construction case to be verified in this research. The initial plan in the case project was the Rock Anchor System. However, as there were terrible miscalculations of basic site conditions that had an extraordinary influence on the underground water level, such as the site's proximity to the Han-river, it was necessary to change the plan to include apermanent drainage system. This achieved a direct construction cost reduction \ 406,702,000 and a maximum sayings of 4% of operational cost, based on the 50-year building Life Cycle Cost.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• autumn
• /
• pp.422-425
• /
• 2003

The purpose of this study is using a TACT planning and scheduling for apartment houses construction that have many of same units. Because using a TACT planning and scheduling is concluded time reduction at same units as apartment plan. The main contents of this study are 1) window and door work through the field study, 2) adjust worker assignment to minimize work time variation, and 3) an effect of working time through a case study. As a result, the total working time can be improved $21.2\%$ by using the TACT planning and scheduling. The stu요 recommends that 1) establish an accurate data between work period and resource, and 2) preparation to measures minimization of waiting time before using a TACT planning and scheduling.

• KIEAE Journal
• /
• v.16 no.1
• /
• pp.37-45
• /
• 2016

Purpose: According to the characteristic of hanok public building, Planning criterion of structure, technology, efficiency, design is needed which can includes various type of new-hanok type public buildings. In this paper, we collect expert opinions to be used as a basis for developing models of New-hanok type Public Buildings. Method: This study was conducted in Research Study and expert surveys. The Part of reviewing Study looked at conception of new-hanok type public buildings model development and overview planning criterion set briefly. Expert surveys were targeted to professors and architects who are related in new-hanok type public buildings model development research. Result: In this study, we suggest improvement direction about planning criterion of new-hanok type public buildings model development based on opinions collected by expert surveys. In conclusion, first, In concept and legal status, it is necessary to adjust clearly than the term and legal status of new-hanok type. Second, various applicability is needed by using new materials and new construction method at the part of planning elements. Third, 'composed structure-convergence type' and 'composed structure-juxtaposed type' should be clearly classified or combined at the part of Setting of type. Forth, improvement on heat insulation, soundproof, waterproof efficiency is demanded to roof, wall, window systems. Fifth, arranging revitalization plan is important.

• Journal of Digital Contents Society
• /
• v.16 no.2
• /
• pp.335-343
• /
• 2015

This paper describes a quantitative approach to the BIM-enabled assessment of building circulation by using quantitative data and applying its weight. Assessment of building circulation plays an important role before construction stage because of related requirements regulated by design guide, building codes, etc. and design decision making as well. In this paper, Qualitative issue is mainly dealt with that are usually excluded from rule checking objects due to their implicit definition such as 'comfortable circulation'. A weighting framework is suggested using weighted data of circulation properties such as 1) metric distance, 2) number of passing spaces, 3) number of turning spaces, 4) window area of passing space, etc.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.387-399
• /
• 2003

The box system that consists only of reinforced concrete walls and slabs we adopted in many high-rise apartment buildings recently constructed in Korea. Recently, many of the box system buildings with pilotis has been constructed to meet the architectural design requirements. This structure has abrupt change in the structural properties between the upper and lower parts divided by transfer girders. For an accurate analysis of a structure with pilotis, it is necessary to have the buildings modeled into a finer mesh. But it would cost tremendous amount of computational time and memory. In this study, an efficient method is proposed for an efficient analysis of buildings those have pilotis with drastically reduced time and memory. In the proposed analysis method, transfer gilders are modeled using super elements developed by the matrix condensation technique and fictitious beams are introduced to enforce the compatibility conditions at the boundary of each element. The analyses of example structures demonstrated that the proposed method used for the analysis of a structure with pilotis will provide analysis results with accuracy for the design of box system buildings.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.816-816
• /
• 2012

최근 우리나라는 기후변화와 이상기후 현상 등의 영향으로 홍수에 대한 위험이 커지고 있다. 홍수에 의해 발생하는 인명 및 재산피해를 최소화하기 위해서는 구조적 및 비구조적 대책 등을 통한 치수정책 수립이 필요하며, 대표적인 비구조적 대책으로는 홍수위험지도(flood hazard map) 제작 등이 있다. 홍수위험지도는 홍수시 침수범위, 침수심 등의 정보를 지도상에 표시하고 있으므로 홍수피해가 발생가능한 공간적 범위를 나타내는 것이다. 홍수위험지도는 침수정보 뿐만 아니라 대피로, 대피처 등 홍수시 피난정보도 함께 나타낼 수 있으므로 홍수발생시 인명 피해를 최소화하기 위하여 활용될 수 있다. 또한 홍수피해 예상범위를 미리 추정할 수 있으므로 피해가능 지역의 특성을 고려하여 구조적 치수계획 수립의 적절한 기준을 제시할 수 있다. 즉, 침수 가능지구 내의 사회적, 경제적, 문화적 중요도를 평가함으로써 지역 특성을 고려한 선택적 홍수방어에 활용될 수 있는 것이다. 본 연구에서는 이러한 중요도 중 홍수피해 예상인구에 대한 현실적인 계산 방법을 제안하고자 한다. 홍수가 발생하여 침수가 예상되는 지역에서 사람이 실제 거주하는 면적을 고려하는 방법은 토지등기부의 지목을 활용하는 것이다. 토지지목은 토지의 종류를 사용목적에 따라 구분한 명칭이며,"측량, 수로조사 및 지적에 관한 법률" 제67조에서 전 답 과수원 목장용지 임야 광천지 염전 대(垈) 공장용지 학교용지 주차장 주유소용지 창고용지 도로 철도용지 제방(堤防) 하천 구거(溝渠) 유지(溜池) 양어장 수도용지 공원 체육용지 유원지 종교용지 사적지 묘지 잡종지 등 28가지 항목으로 구분된다. 여기서 대(垈) 지목은 영구적 건축물 중 주거 사무실 등의 부지를 의미하므로 상주인구가 거주하는 지역으로 가정할 수 있다. 침수가 예상되는 지역에서 대(垈) 지목의 면적을 고려하여 계산된 인구수와 단순 면적비로 계산된 인구수를 비교한 결과, 도시화의 비율이 높은 지역일수록 단순 면적비에 비해 인구수가 높게 계산되었고, 농경지 및 산지가 발달된 지역일수록 단순 면적비에 비해 인구수가 낮게 계산되었다. 따라서 침수가 예상되는 지역의 인구수를 예측할 경우 토지지목 중 대(垈) 지목의 면적을 고려하여 계산하는 것이 보다 합리적인 홍수피해 예상인구를 계산하는 방법으로 판단된다.