• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.5
• /
• pp.71-79
• /
• 1995

This paper describes the design and implementation of dryer controller using the dual processor. This system has higher performance of system recovery from the noise than the existing single processor dryer. And in this paper temperature control method of Dryer using on-off fuzzy logic is proposed to improve the overshoot of temperature in dryer. Experimental results shows that the performance of fuzzy controller is better than that of controller based upon on-off control method.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.3 no.4
• /
• pp.57-61
• /
• 1989

이 논문은 phenolic resin의 CTI에 대하여 기압을 파라메터로 고찰하였다.(IEC publication 112[습식법]). 1) 기압이 낮아짐에 따라 건조대의 형성 및 미소 불꽃방전을 발생하는 개시 적하수는 300[V] 이상에서 증가되고 있다. 2) 900[mb]에서 Tracking 파괴 적하수가 가장 높으며 기압이 낮아 질수록 CTI의 값은 증가하고 있다.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.05a
• /
• pp.217-220
• /
• 2002

할론 등 CFC 계통의 소화약제는 환경오염물질을 내포하며, 지구온난화지수와 오존파괴지수 등이 높아 전세계적으로 그 사용이 중단되고 있다 또한, IMO의 SOLAS Chapter II-2에서는 소화설비에 대한 규정으로 할론소화장치의 새로운 설치를 금지하고 있으며, 2002년 7월 1일 이전에 건조된 2,000톤 이상의 현존 여객선은 기관실 전체를 방호하는 고정식 수계국소방출소화설비를 설치하여야 한다고 규정하고 있다. 이에 대체소화기술의 하나로 관심을 끌며 연구되기 시작한 소화방법이 미세물분무노즐을 이용한 소화설비이다.(중략)

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.27 no.6
• /
• pp.541-547
• /
• 1998

공기 중에 존재하는 미생물(바이오에어로졸, bio-aerosol)은 많은 질병 발생의 원인이다. 의학계에서는 바이오에어로졸과 공기 매개성 질병의 전파와의 연관성이 잘 알려져 있다. 특히 결핵, 수두, 홍역, 천연두의 발병은 공기를 통한 질병 전파의 중요성을 확인시켜 준다. 그러나 IAQ(indoor air qualify)의 영향은 최근에서야 조사되었다. 보건의료기관과 연구실험실에서는 세균과 진균의 감염이 HVAC 시스템을 통해서 종종 일어난다. 유사한 IAQ연구에서는 바이오에어로졸이 빌딩증후군과 같은 빌딩과 관련된 질병(building-related illness, BRI), 감염, 중독성 증상, 민감성 질병과 1차적으로 연결되어 있음을 발견되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.569-574
• /
• 2020

A floating dock is the main facility for launching ships. In the early 2000s, ship-launching technology using floating docks was developed in Korea. Therefore, the opportunity to participate in new construction projects without investment in dry docks has expanded. In this paper, a basic calculation for the safe mooring of a floating dock was performed, and a mooring system was designed based on this. This study was conducted considering the typhoon situation, which is the most serious environmental requirements of Daebul Pier, a site to be installed and operated, for a floating dock. The design load was calculated by wind load, tidal load, and wave-induced load in accordance with the internationally accepted standards. After performing the initial arrangement of the mooring line of the floating dock using the existing mooring facilities of Daebul Pier, the minimum breaking load for each mooring line was calculated for the given load. Based on the calculation, the mooring arrangement was modified to minimize the breaking load, and a final specification of each mooring line was selected.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.183-188
• /
• 2009

RFID method is a non-contact automatic identification technology, which attaches microchips and antennas to an object in a tag form, to send and process information sent to the network using wireless frequency. Drying and curing process is extremely important which minimizes the resistivity of RFID antennas. This research is about the drying characteristic of conductivity ink, and analyzes and compares the hot-air drying process and infrared drying process. Also, the research was done for the improvement in drying performance by using combined process of hot-air and infrared mechanism. The experiment result shows that the hot-air or infrared drying system used alone cannot meet the required performance in drying printing method using conductivity ink. The combined drying system of hot-air and infrared ray showed resistance low enough in short drying and curing time, and this mechanism makes drying and curing process for mass and continuous production possible on-line.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1429-1434
• /
• 2009

Recently electronic circuit pattern printing technologies like antennas of RFID process are paid attention. oven drying system is being used since drying and curing time of RFID Tag Gravure printing normally takes from 5 minutes and up to 30 minutes long. In this case the parental material which is of a sheet shape is possible, however, for a massive and a continuous production drying and curing process must be done on-line. This research compared and analyzed the an oven type drying device and a traditional hot-air drying device. Considering the experiment result, the cell depth that shows low resistivity, which doesn't consider the pattern difference, is $31{\sim}33{\mu}m$. Also, oven drying system showed some resistivity after around 120 seconds of drying time, and showed much better performance in minimum resistivity compared to the hot-air drying system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.12
• /
• pp.867-874
• /
• 2012

In the present study, three-dimensional transient numerical simulations were carried out to improve the performance of a vehicle paint drying process. In order to describe the movement of a vehicle, the techniques of moving boundary condition and multiple reference flames (MRF) were used. For the validation of the numerical analysis, the predicted temperature on the surface of a vehicle was compared to the experimental data, and a good agreement was achieved. With validated numerical procedure, various operating conditions of the temperature and the flow rate of the supply air were investigated to improve the drying performance of the facility. It is shown that the optimization of the operating condition can lead to energy savings and faster line speed of the production.

• Proceedings of the KAIS Fall Conference
• /
• 2008.11a
• /
• pp.397-399
• /
• 2008

흡착식 건조공정에서 가장 중요한 부분은 건조에 활용되는 용해제(Desiccant) 라고 할 수 있다. 그러나 국내에서 흡착식 건조기에 사용되는 대부분의 용해제는 수입에 의존하고 있는 실정이다. 그러므로 본 연구에서는 흡착식 제습 설비의 제작 능력을 기초로 하여 용해제의 자체 개발을 통하여 안정적인 기술력의 확보로 국내에서 친 환경적이며 무동력으로 사용할 수 있는 용해성 흡습제에 관한 연구를 진행하고자 한다. 이를 위해 알칼리성 흡수제를 합성하기 위하여 KCl, NaCl 그리고 $CaCl_2$ 등의 물질을 질량비로 일정비율이 되도록 수용액에 용해시켜 교반속도가 유지되는 회분식 반응기에서 일정시간 동안 반응 시킨 후 일정온도 범위에서 일정시간동안 건조시켜 시료를 제조 하여 흡습제의 조습특성을 분석하였다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.251-254
• /
• 2007

본 연구는 $SF_6$를 대체하기 위한 건조공기(Dry-Air)의 특성을 연구할 목적으로 교류 및 직류고전압 인가 시 압력(P)변화 및 갭 길이의 변화에 따른 절연파괴특성을 연구하였다. 본 연구를 통해 챔버 내의 P가 증가할수록 절연파괴특성은 증가하는 것을 확인했다. 그리고 불평등전계 보다 평등전계에서 절연파괴특성이 더 증가하고 전극간거리(d)가 증가할수록 절연파괴특성이 증가하는 것을 확인했다.