• Korean Journal of Food Science and Technology
• /
• v.9 no.1
• /
• pp.61-67
• /
• 1977

Seed separation from half-cut red pepper were investigated with free falling, up-and-down shaking and rotating collision methods. The separation rates were related with impact appiied and the rotating case was distinguished from the other two methods. Beside the impact effect, velocity of the pod and tumbling factors were involved. Momentum effectiveness of seed separation were calculated as $2.50{\times}10^{-6}$, $2.09{\times}10^{-6}$, and $3.94{\times}10^{-8}$ for free falling, shaking and rotating method on the same velocity basis, respectively. The tendency of separation rate was similar to that of red pepper drying rate against time.

• Journal of agriculture & life science
• /
• v.45 no.4
• /
• pp.87-93
• /
• 2011

This study was carried out to determine more effective way in eave structure between lengthening roof just as standard plan and replacing 3 types of vertical rain roof facility by using computational fluid dynamics (CFD) simulation to reduce the heat stress of Hanwoo, increase the effect of dryness of room floor, rain proof and ventilation efficiency. The simulation which did with mean wind velocity (1.2 m/s) result showed that the case of lengthening of roof just as standard design was more effective than the cases of vertical establishment of rain proof facility.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.644-655
• /
• 2023

Purpose: Metal fires occur in metal handling, processing, waste storage plants, etc. It is difficult for firefighters to extinguish metal fires, and it takes a long time, so caution is needed in fire suppression. Method: In this study, current statistics and problems of metal fires were introduced, and then the effectiveness was verified by experiments with using fire extinguishing agents used in Korea. Comparative suppression experiments of 5 different fire extinguishing agents for burning powders of 99.9% magnesium over 150 ㎛ were performed following the metal powder type test method of Class D fire in ISO 7165. Result: 5 fire extinguishing agents are the power types of dry sands and expanded vermiculites most commonly used in Korea, the certified class D fire extinguisher used abroad, and ochers requiring verification, and the liquid silica gel. Conclusion: The results of experiments showed expanded vermiculites were the best metal fire extinguishing agent considering effectiveness, convenience of use, and economical feasibility.

• Journal of Applied Biological Chemistry
• /
• v.59 no.3
• /
• pp.189-201
• /
• 2016

A processing factor (PF) has been used to define the maximum residue limits of pesticide in a variety of processed fruit products. This study summarizes PF by the stage of fruit processing based on JMPR reports from 2010 to 2014. When we compared PF of 19 pesticides in apple products during the processing of washing, drying, canning, juice, sauce, puree and pomace, PF was higher than 1 only in pomace. In the comparison of 21 pesticides during the process of grape (washing, juice, wine and raisin), PF was higher than 1 in raisin. In the comparison of 19 pesticides during the process of orange (juice, oil and marmalade), PF was higher than 1 in oil. When 27 pesticides were compared during the process of tomato (juice, puree and paste), paste showed the highest PF value except pomace. During the process of plum (washing, drying and puree) with 12 pesticides, PF was higher than 1 in drying. The correlation coefficients between physical characteristics of pesticide (fat-solubility and volatility) and PF were statistically significant in the processes of apple juice, orange juice, tomato puree and paste and strawberry jam.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.04a
• /
• pp.117.1-117
• /
• 2003

새송이 버섯은 맛과 향이 좋고 영양적으로 우수하여 성인병 예방과 개선 효과가 있다고 알려져 있으나 재배농가의 급증으로 인한 가격하락과 집중출하로 신선도의 하락 등이 문제가 되고 있어 새송이 버섯의 활용성을 향상시키고, 소비자의 기호를 충족시킬 수 있는 버섯류 가공품 개발이 요구되고 있다. 전통절임식품을 응용한 새로운 버섯류 장류절임 가공법을 개발하기 위하여 절임 전 처리에 따른 품질특성을 비교하였으며, 이를 위하여 먼저 절임 전처리 조건으로 블랜칭처리, 적정 염농도와 처리시간 및 탈염법을 개발하고 건조 등의 전처리에 따른 품질 평가는 수분함량, 염도, 색상, 조직감, 관능특성 등을 평가하였다. 새송이 버섯을 전처리하기 위한 블랜칭 처리조건은 7$0^{\circ}C$에서 10분간 처리한 구가 조직감이 우수하고 갈변이 적었으며 염 침지시간은 침지 72시간까지는 증가하였으나 그 이후로는 증가하지 않았고 4$0^{\circ}C$에서 탈염하는 것이 가장 우수하여 전처리 조건으로 선정하였다. 전처리 방법에 따른 중량변화는 블랜칭 처리가 약 10% 정도 중량이 더 많았으며 이 영향은 건조 후에도 지속되었다. 수분함량도 블랜칭 처리가 높았으며 염도 또한 건조 처리에 따라 높은 함량을 보였으나 블랜칭 처리를 병행했을 경우 낮은 값을 나타내었다. 조직의 강도는 무처리에 비하여 전처리를 함에 따라 많은 힘이 소요되어 질긴 조직 특성을 나타냄을 알 수 있다. 관능평가 결과 블랜칭 처리를 단독으로 실시한 B(B)처리구가 관능적 특성치 모두 높은 값을 보여 전처리 방법으로는 가장 우수한 전처리 방법임을 알 수 있었다.저온 장시간 처리한 경우에 비하여 낮은 수준이지만 약간의 증감 경향을 보이다가 고른 평형 상태를 유지하였다. 산소 농도는 저온 장시간 처리 직후 급격히 저하된 후 다시 증가하였으며 저장 7일 후에는 4$0^{\circ}C$ 3시간 처리구를 제외하고는 평형 상태를 유지하였다. 고온 단시간 처리구의 경우 처리 직후부터 저장 7일 후까지 고른 평형 상태를 유지하였다. 에틸렌의 경우 저온 장시간 처리구는 처리 직후 그 농도가 급격히 상승하였다가 저장 1일 후부터 대조구보다 낮은 값을 나타내었다. 고온 단시간 처리구의 경우 저온 장시간 처리구와는 달리 저장 1일 후부터 그 농도가 다소 상승되었다가 다시 감소는 경향을 보였다. 한편 열처리하여 냉각시킨 직후 및 저장1주 후 사과의 pH, 산도, 당도, 경도, 과육의 갈변도 등을 조사하였던 바 대조구 및 처리구간에 일부 항목에 있어서는 약간의 차이를 나타내었다. 대치할 수 있을 것이라고 사료된다. 수분함량은 기계적 검사보다 관능검사와 더욱 높은 상관관계를 나타냈다.내었다. 항균활성이 우수한 생약재를 농도별로 활성을 조사한 결과, 물 추출물과 10% Ethanol 추출물 모두 낮은 농도에서도 우수한 항균활성을 나타내었다.취와 함께 점질성 갈변물질이 생성되었다. 이와 같은 결과로 볼 때, BAAG의 처리는 BAAC의 경우보다 가격은 저렴하면서도 항균력은 우수한 천연 항균복합제재로써 농산물 식품원료에 적용하여 선도유지 기간을 연장할 수 있는 효과를 기대할 수 있었다. 과일 등의 포장제로서 이용할 가능성을 확인하였다.로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻

• Journal of the Korean earth science society
• /
• v.31 no.4
• /
• pp.313-321
• /
• 2010

The landform of the study area is defined as a small-scale alluvial plain in the valley bottom adjacent to the coast. By the aggradation of alluvial materials, this valley bottom plain was formed in dissected parts of low hills. For the purpose of reconstructing the palaeo climate environment in this study, $\delta^{13}C$ analysis and soil organic carbon analysis are therefore employed. Main results of this study are as follows: Section I: the period of $6,600{\pm}60yr$ B.P.$-5,350{\pm}60yr$B.P. was mostly in warm and humid climate environment. A little changes of the humid environment are detected as subdry (or sub-humid)${\rightarrow}$humid in terms of the dryness and wetness. Section II: the period of $5,350{\pm}60yr$ B.P.-2,200 yr B.P. was in warm and humid climate environment, which is similar to the present. However, The sediments between $4,720{\pm}60yr$ B.P. and $4,210{\pm}50 yr$ B.P. experienced the most humid climate environment of all studied sedimentary layers. After $4,210{\pm}50 yr$ B.P., the environment started to change from the humid to the sub-humid (or sub-dry) climate. Section III: the period of 2,200 yr B.P.$-210{\pm}60 yr$ B.P. was distinguish from previous two sections as the environmental changes to sub-humid (or sub-dry) climate was apparent.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.8
• /
• pp.17-28
• /
• 2015

The purpose of this study is to measure the volumetric water content of unsaturated soils during drying and wetting process by using volumetric pressure plate extractor (VPPE) incorporated with time domain reflectometry (TDR). The VPPE consists of a pressure cell, a pressure regulator, a burette system and a TDR probe. Two samples with different initial void ratios were prepared in the pressure cell, and the air pressure at the range of 0.1 kPa - 50 kPa was applied to adjust the matric suction by the pressure regulator. The burette system was used to measure the volumetric water content change of the sample according to the matric suction. In addition, the TDR probe, installed in the cell, was used to evaluate the dielectric constant from the reflected signal of the electromagnetic wave at the probe. The volumetric water content of specimen was estimated by the empirical equation between the volumetric water content and dielectric constant, which was calibrated with the Jumunjin sand. The test results show that the volumetric water content calculated by TDR probe is strongly correlated to the measured value by burette system. The hysteresis occurs during drying and wetting process. Furthermore, the degree of hysteresis reduces in the repeated process. This study suggests that TDR may be effectively used to evaluate the water content soil for the determination of water characteristic curve of unsaturated soils.

• Journal of Bio-Environment Control
• /
• v.12 no.4
• /
• pp.200-206
• /
• 2003

Pleurotus eryngii(King oyster) is one of the most promising mushrooms produced on the domestic farms. The quality as well as quantity of Eryngii is sensitively affected by micro climate factors such as temperature, relative humidity, $CO_2$ concentration, and light intensity. To safely produce high-quality Eryngii all the year round, it is required that the environmental factors be carefully controlled by well designed structures equipped with various facilities and control systems. At the commercial mushroom cultivation house(A,B), this study was carried out to find out reasonable range of each environmental factor and yield together with economic and safe structures influencing on the optimal productivity of Eryngii. this experiment was conducted for about two-month from Nov. 11, 2002 to Dec. 30, 2002 in Eryngii. cultivation house-A, B. Ambient temperature during the experiment period was not predominantly different from that of a normal year. The capacity of the hot water boiler and the piping systems were not enough. Maximum air temperature difference between the upper and lower growth stage during a heating time zone was about 2~3$^{\circ}C$. The max. and min. relative humidity were ranged approximately 60~100%, and average relative humidity was ranged approximately 80~100%. And $CO_2$concentration increased until maximum 1,600~1,800 ppm with the passing growing period. The illuminance in cultivation house was widely distributed from 20lx to 160 lx in accordance with position, and it was maintained lower than the recommended illuminance range 100~200 lx. The average yield per bottle was about 67~85g. But the optimal productivity will be evaluated by considering the quality and quantity of mushroom production, energy requirements, facility construction and management cost, etc.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.1-11
• /
• 2015

Seated Amitabha Triad at Muwisa Temple (Treasure No. 1312) had been known as wooden Buddha statue, but a precise safety inspection revealed that the statue is terracotta Buddha statue made with clay. The clay layer of Amitabha Triad was conserved due to its severe damage. In this study, experiments were conducted to produce the most appropriate filler for the conservation treatment of the seated Amitabha Triad. Mixed clay samples with various ratios were produced and surface hardening state, crack, color change, and shrinkage of the samples during dry process were measured. Loess, fine sand powder, and cotton were used to produce the mixed clay for the filler with six different ratios and then 12 different concentration glues made with glutinous rice glue, Pachymeniopsis Elliptica glue, and animal glue were added as adhesives. Total 72 types of samples were prepared and comparative study was conducted. As a result, when the mixed clay contains 2.5% cotton compared to the weight per cent of loess and fine sand powder and also loess and fine sand in the mixed clay have a 15:1 ratio, the mixed clay had the lowest shrinkage. Animal glue is considered as an appropriate glue since it had small color change, low physical property change and shringkage. Therefore, mixed clay (loess:fine sand=15:1) mixed with 15ml animal glue is likely to be a suitable filler for conservation treatment of the seated amitabha triad at the Muwisa Temple.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.2
• /
• pp.33-42
• /
• 2014

The shear strength and deformation characteristics of granular soils at low confining stresses differ from those with high confining stresses. Thus, the clear understanding of geotechnical problems related to the low confining stress state such as the stability of shallow foundations, embankments, slope failure, debris flow characteristics and liquefaction as well as the various laboratory model tests is needed. In this study, drained triaxial compression tests with the cell pressures from 5 kPa to 300 kPa were performed on dry Jumunjin sand. The results show that the internal friction angle and deformation modulus are dependent on the confining stress. Also, the correlations between them on the dense and loose sand were established.