• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.807-811
• /
• 2002

In this work, we investigated the deposition behavior of Mo/Si multilayer thin film structures simulated by a PVD process simulator based on Monte Carlo method to assist the optimized fabrication of the high quality mask in EUVL(Extreme Ultra-Violet Lithography) process. The shape of simulated thin film structures turned out to be largely dependent on the gas pressure(1∼30 mTorr), the target-substrate distance(1∼30 cm) and the diffusion length(1∼10 nm). From the simulation studies, it was predicted that relatively uniform thin film structures can be fabricated by decreasing gas pressure and increasing the target-substrate distance.

• Journal of Energy Engineering
• /
• v.14 no.4 s.44
• /
• pp.241-247
• /
• 2005

Heat transfer enhancement and pressure loss penalty caused by three-row winglets built in three-row tube-bundles in an in-line arrangement, are compared between 'common flow up' and 'common flow down' winglet configurations. The 'common flow down' winglet-pairs recommended by the previous researchers bring about $10\%$ to $25\%$ increase in heat transfer enhancement and $20\%$ to $35\%$ increase in pressure loss penalty, in comparison with fin-tube bundles without winglets. For the 'common flow up' winglet-pairs, the spanwise distance between the trailing edges (${\Delta}y$) of winglet pairs was changed and investigated. Two types ot winglet are applied for triangular and rectangular shapes. In the triangular winglets with ${\Delta}y$=5 mm in in-line tube bundles, the heat transfer increased up to $10\%$, and simultaneously the pressure loss decreased by $8\%$ to $15\%$ for the Reynolds number (based on two times channel height) ranging from 300 to 2700, when the 'common flow up' winglets were built in. The performance of fin-tube bundles with triangular winglets is much superior to the rectangular one, because of the smaller pressure-loss penalty.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.135-140
• /
• 2021

In this study, the concrete aggregate shape features were extracted from the cross-section of a normal concrete strength cylinder, and the compressive strength of the cylinder was predicted using artificial neural networks and image processing technology. The distance-angle features of aggregates, along with general aggregate shape features such as area, perimeter, major/minor axis lengths, etc., were numerically expressed and utilized for the compressive strength prediction. The results showed that compressive strength can be predicted using only the aggregate shape features of the cross-section without using major variables. The artificial neural network algorithm was able to predict concrete compressive strength within a range of 4.43% relative error between the predicted strength and test results. This experimental study indicates that various material properties such as rheology, and tensile strength of concrete can be predicted by utilizing aggregate shape features.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.6
• /
• pp.343-349
• /
• 2022

This paper proposes a new topology optimization scheme to determine optimized joints for multi-component models. The joints are modeled as zero-length high-stiffness spring elements. The spring joints are considered as mesh-independent springs based on a joint-element interpolation scheme. This enables the changing of the location of the joints regardless of the connected nodes during optimization. Because the joints are movable, the locations of the optimized joints should be aggregated at several points. In this paper, the novel joint dispersal (JD) constraint to prevent joint clustering is proposed. With the joint dispersal constraint, it is possible to determine the optimized joint location as well as optimized topologies while maintaining the minimum distance between each joint. The mechanical compliance value is considered as the objective function. Several topology optimization examples are solved to demonstrate the effect of the joint dispersal constraint.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.2
• /
• pp.23-28
• /
• 2013

Microlens array as basic element of the optical system have been fabricated with various focal length (mainly with long focal length) depending on the purpose of application. In this paper, the microlens arrays were fabricated for observing fluorescent images within sol-gel. Though the fluorescent signal is very low, the microlens array can help obtaining clear images through extracting the fluorescent light from sol-gel. We fabricated microlens arrays with short focal length, which can extract the light using photoresist thermal reflow method. In the experiment, the diameter of microlens decreased after thermal reflow because the solvent within the photoresist was vaporized. Therefore, to compensate the shape error by this reduction, microlens diameter in photomask was altered and spin-coat recipe of photoresist were modified.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.72-75
• /
• 2003

In this research, we focused on the effects of the orifice internal flow such as cavitation and hydraulic flip. The breakup characteristics such as the breakup length and trajectory were measured by changing the orifice diameter (d), the orifice length/orifice diameter (L/d), the injection pressure and the shapes (sharp and round) of orifice entrance to provide a lot of conditions of the orifice internal flow. It is found that cavitation bubbles that occur inside the sharp-edged orifice make the liquid jet ejecting from the orifice turbulent. In the orifices (L/d = 5), the hydraulic flip phenomenon is shown when the injection pressure is high. In case cavitation occurs it breaks up more earlier than that in case of non-cavitation. In case hydraulic flip occurs, since the area of the liquid jet becomes small, the breakup length is also small as that in case of cavitation. But the liquid column trajectories have a similar tendency irrespective of cavitation.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.135-135
• /
• 2019

수제는 만곡부의 유로 조정이나 하상보호와 같은 하천공학적인 목적을 가진 수공구조물이다. 본 연구에서는 개수로 만곡부에 수제 설치 시 외측벽과 수제 사이의 거리에 따라 하상변동이 어떤 차이가 있는지를 파악하기 위해 이동상 수리실험을 했다. 본 연구에서는 폭 1.45 m, 길이 24 m인 $90^{\circ}$ 만곡수로에 $4.2{\times}8.4cm$의 직사각형 단면 수제를 외측으로부터 이격하여 2열로 설치하였다. 하상재료는 $d_{50}$이 3.3 mm인 잔자갈을 사용했고 하상경사는 1/300로 하였다. 실험은 평균 유량 163 l/s를 3시간 동안 공급했고, 종료 후 만곡부의 주요횡단면별 하상고를 측정했다. 여기서 실험별 이격거리는 8.4 cm, 14 cm, 19.6 cm로 하였다. 실험 결과 외측벽과 수제 사이의 거리가 멀어질수록 만곡부의 최대세굴심은 커지고 그 발생 위치는 하류로 이동하는 경향을 보였다. 만곡부 최대세굴이 발생한 횡단면 형상은 만곡 내측에서 외측방향으로 무차원 위치 $y_1$(=내측에서의거리/폭)가 0.27보다 작으면 퇴적에 의해 하상이 상승하고, 0.35보다 클 때는 세굴에 따른 하상저하가 나타났다. 만곡 외측벽 부근 하상은 이격거리가 짧을수록 수제 설치에 의한 하상고 변화가 작았다.

• Proceedings of the IEEK Conference
• /
• 2002.06d
• /
• pp.223-226
• /
• 2002

영상 검색을 위한 기존의 칼라 히스토그램 방법은 영상의 형상 정보를 포함하고 있지 않다. 본 논문에서는 로컬 형상 정보인 에지 정보에 칼라 정보를 접목시켰다. 각각의 세 종류의 에지(수평 에지, 수직 에지, 비 방향성 에지) 주위의 픽셀들에 대한 칼라 분포를 구한 후 그 각각의 칼라 분포를 기초로 구한 두 영상간의 거리 정보를 이용하여 영상들간의 유사도를 구했다. 따라서 본 논문에서 제안한 유사도는 한 종류의 에지 타입 (비 방향성 에지)을 이용한 방법에 비해 매칭 오류를 줄일 수 있었다. 실험 결과, 제안된 방법이 기존의 칼라 히스토그램과 에지 히스토그램을 이용한 방법에 비해 향상된 성능을 보였다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.301-304
• /
• 2005

본 논문은 개폐기의 접점 형상에 따른 전계 분포 특성을 2차계 전자계 해석 program인 Flux-2D를 통해 살펴보았다. 2개의 모델을 선정하여 전극간 이격거리를 115[mm], 120[mm], 125[mm]로 변화를 주었을 때 최고 전계 강도의 변화를 살펴보았다. 1000[V] 인가시 최고 전계 강도는 (a)모델에서 115[mm]일 때 61.84[V/m], (b)모델에서 115[mm]일 때 66.90[V/m]로 나타났다.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.656-659
• /
• 2011

X-선 검색장치는 대상체의 단면을 스캔하여 결과를 확인하기 때문에 정확성이 낮다는 것이 문제점으로 지적되어왔다. 이를 개선하기 위하여 선행연구로 스테레오 X-선 검색장치를 개발하여 단일 대상체에 대하여 윤곽선 정합 및 볼륨기반 형상복원 연구를 수행하였다. 본 연구에서는 스테레오 X-선 검색장치를 이용하여 두 개의 중첩된 대상체를 스캔하여 형상을 분리 복원하기 위한 연구를 진행하였다. 중첩 대상체에 대한 분리 복원을 위해 벡터정보의 거리값을 계산하여 내 외부 복셀을 분리하고 중첩부분에 대한 제거는 Z축을 기준으로 임계치를 두어 분리하는 알고리즘을 제안하였다. 3차원 스테레오 X-선 검색장치에 대한 스캔영상의 형상복원 알고리즘 개선을 통해 제한된 스캔환경에서 집적화된 대상체의 검색을 가능하도록 할 것이다.