• Journal of the Korean Geotechnical Society
• /
• v.22 no.10
• /
• pp.93-100
• /
• 2006

The lateral soil movement in soft grounds undergoing improvement with application of vertical drains is analyzed on the basis of monitoring data at three fields, in which fifty six monitoring sites are located. Based on the investigations, the criterions are suggested to predict the lateral soil movement. In order to predict the lateral soil movement in the improved soft grounds by using the dimensionless parameter R suggested by Marche & Chapuis (1974), it is desirable that the maximum lateral displacement in the soft ground below the toe of embankment should be applied to calculate R instead of the lateral displacement at the toe of embankment. The lateral soil movement may increase rapidly, if the safety factor of slope is less than 1.4 in case of high ratio of H/B (Thickness of soft ground/Embankment width) such as 1.15 or is less than 1.2 in case of low ratio of H/B such as 0.05. Also, the graph suggested by Tschebotarioff (1973), which illustrates the relationship between the maximum height of embankments and the undrained shear strength of soft grounds, can be applied to the evaluation for the possibility of the lateral soil movement due to embankments on soft grounds.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.7
• /
• pp.57-64
• /
• 2007

This study proposes a method to estimate drilling torque during ground boring with an aid of electrical energy required for rotating a boring-auger. Ground boring is commonly used in geotechnical engineering such as preboring precast pile installation, soil-cement grouting, ground exploration and so forth. In order to understand the correlation between required electrical energy to rotate the boring auger and the drilling torque, a small laboratory apparatus was designed and a pilot study was performed. The apparatus rotates common drill bits of $D=5{\sim}25mm$ in CBR specimens. The velocity of a bit is 19 RPM and predefined using a reduction gear which connects a main rotation axis to a 25 Watts AC electrical motor shaft. In the middle of drilling the motor current increments and the drilling torque were measured and the correlation between the current and the torque was obtained through linear square fits. Based on the correlation the acquired motor current during drilling was applied to predict the drilling torque in consequent testing and the prediction results were compared to the measured torque. The comparison leads a conclusion that the motor current during drilling using electrical power may be a good indicator to estimate/determine strength characteristics of the ground.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.55-63
• /
• 2024

Xanthan gum biopolymer is an ecofriendly ground stabilizer that maintains stability in a wide range of temperatures and pH values. The binding effect of sandy soil particles realized by injecting xanthan gum biopolymer is dependent on the xanthan gum matrix, which is formed during the drying process; thus a study on the effects of the drying process of the xanthan gum solution on the changes in stiffness characteristics of sandy soil is required. In this study, shear wave velocity and electrical resistivity were monitored in sandy soil specimens saturated with biopolymer solutions of different gravimetric concentrations to investigate the improvement effects of biopolymer-treated sandy soils with the drying process. The experimental results reveal that both shear wave velocity and electrical resistivity increase during drying process. The results demonstrate the stiffness improvement effects of biopolymer-treated sandy soils. In addition, a higher stiffness improvement effect was monitored in the biopolymer-treated sandy soils with a higher gravimetric concentration. The results of this study may be used to estimate the stiffness improvement effects of sandy soils treated with biopolymer solutions with the drying process.

• Journal of Plant Biotechnology
• /
• v.50
• /
• pp.63-69
• /
• 2023

This study includes the transformation of genes such as ORE7, the increase of gene expression, and the use of the bar gene as a selectable marker that shows herbicide resistance with Agrobacterium tumefaciens using hypocotyls from the oilseed rape "Youngsan" cultivar. To establish an Agrobacterium transformation system for the production of oilseed rape with a high-yield trait, infection time and co-cultivation period with Agrobacterium were tested. Therefore, when hypocotyls from the oilseed rape "Youngsan" cultivar were infected with Agrobacterium for 20 min and co-cultivated for 3 days, approximately 32-36 putatively transformed hypocotyls with shoots including roots survived from 100 inoculated hypocotyls after 4 weeks of transformation on a selection medium containing 20 mg/L of phosphinothricin (PPT) as a selectable agent. Additionally, a PCR assay was performed to confirm the insertion of target genes and showed the presence of the ORE7 gene as a high-yielding trait and the bar gene as a selectable marker. Treatment with 0.5% (v/v) Basta solution as a selectable agent for 6 days with leaves from transformed oilseed rape expressed the bar gene. Therefore, this study can contribute to the development of special oilseed rapes containing agriculturally useful traits such as herbicide resistance, drought tolerance, high yielding traits, and high oleic acid content.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.21-36
• /
• 2005

Although the main geology of Korea consists of granite and gneiss, it Is not uncommon to encounter anisotropy Phenomena in crosshole radar tomography even when the basement is crystalline rock. To solve the anisotropy Problem, we have developed and continuously upgraded an anisotropic inversion algorithm assuming a heterogeneous elliptic anisotropy to reconstruct three kinds of tomograms: tomograms of maximum and minimum velocities, and of the direction of the symmetry axis. In this paper, we discuss the developed algorithm and introduce some case histories on the application of anisotropic radar tomography in Korea. The first two case histories were conducted for the construction of infrastructure, and their main objective was to locate cavities in limestone. The last two were performed In a granite and gneiss area. The anisotropy in the granite area was caused by fine fissures aligned in the same direction, while that in the gneiss and limestone area by the alignment of the constituent minerals. Through these case histories we showed that the anisotropic characteristic itself gives us additional important information for understanding the internal status of basement rock. In particular, the anisotropy ratio defined by the normalized difference between maximum and minimum velocities as well as the direction of maximum velocity are helpful to interpret the borehole radar tomogram.

• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.3
• /
• pp.180-190
• /
• 1989

In order to obtain basic information on soil inprovement and management of two reclaimed paddy soils, Munpo and Pori series, this study was carried out by investigating the change of physico-chemical and soil mechanical properties. 1. In the Munpo series, the contents of salt in the soil and ground water before paddy rice transplanting at 6 years after reclamation were 0.60 and 1.84%, respectively, and the safty cultivation of paddy rice was possible after 20 years, while that of the Pori series was after 12 years. 2. In the Munpo series, the change of the soil particle size according to the ages after reclamation showed negative correlation with sandy contents, but clay contents had positive correlation both in the surface and subsurface soils. The pori series showed reverse tendency. 3. Between the N-value and Atterberg limits and the ages showed negative correlation in both Munpo and Pori series, but clay-activity showed positive. Arid the cole values showed positive correlation in the Munpo series, but negative in the Pori series. 4. Cone penetrating resistance in the surface of the Munpo series after 6 years of reclamation was 62.9, after 20 years 24.5 and $16.7kg/cm^2$ in 15cm of soil depth at depth of 22.5cm after 27 years. In the Pori series, it was $3kg/cm^2$ at 15-20cm of soil depth after 12 years and it used after being creation of hard pan layer after 23 years. 5. Change of the clay minerals by the different year after accomplishment of tidal reclamation did not show. The major clay minerals were illite and kaolinite, and accessory clay minerals were montmorillonite and vermiculite in both Munpo and Pori series.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.4
• /
• pp.5-11
• /
• 2014

Recently, there have been various lifeline installations constructed in the underground space of urban area due to the effective use of land. For newly installed lifelines or the management of the installed lifelines, many construction activities of excavation and backfilling are observed. Around these area, there are possibilities of collapse or excessive settlement due to the leaking of the pipe or unsatisfactory compaction of backfill material. Besides, construction costs can be saved since the on-site soils are used. The application of this liquidity filling material is not only to the lifeline installation but also to underpin the foundation under the vibrating machinery. On the evaluation of the applicability of this method to this circumstance, the strength should be investigated against the static load from the machine load as well as the vibration load from the activation of the machine. In this study, the applicability of the liquidity fill material on the foundation under the vibrating machinery is assessed via uniaxial compression and resonant column tests. The liquidity filling material consisting of the on-site soils with loess and kaolinite are tested to investigate the static and dynamic characteristics. Furthermore, the applicability of the reclaimed ash categorized as an industrial waste is evaluated for the recycle of the waste to the construction materials. The experimental results show that the shear modulus and 7 day uniaxial strength of the liquidity filling material mixed with reclaimed ash show higher than those with the on-site soils. However, the damping ratio does not show any tendency on the mixed materials.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.3
• /
• pp.164-176
• /
• 2012

In the present study, rapeseed flour (RSF), which is a by-product from the production of edible oil and biodiesel extracted from rapeseed, was used to develop alternative adhesives for the production of plywood panels. To examine the effects of the enzyme on the adhesive properties and formaldehyde emission of the RSF-based adhesive resins, three enzymes, such as cellulase (CEL), pectinase (PEC) and protease (ALC), were used either separately or together. As a crosslinking agent, PF prepolymers, which were prepared with 1.5, 1.8 and 2.1 mole formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), were added into the RSF hydrolyzates. The adhesive resins formulated with CEL- or CEL-PEC-RSF hydrolyzates and 1.8-F/P PF prepolymers exhibited excellent adhesive strengths and formaldehyde emission. The tensile shear strength and formaldehyde emission of the plywood panels bonded with the formulate resins were satisfied with the minimum requirement of the KS standard for ordinary plywood panels (0.6 N/$mm^2$). In addition, formaldehyde emissions of the plywood panels approached to that of E0 specified in the KS standard (0.5 mg/${\ell}$), and even had much better than those of commercial UF glue mixes. Overall, the use of RSF-based adhesive resins for the production of plywood panels might provide durable adhesive properties and an environmentally friendly substitute for petroleum-based adhesive resins. However, further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Korean Journal of Plant Resources
• /
• v.21 no.1
• /
• pp.1-4
• /
• 2008

The clonal variation in female flowering was studied in Larix leptolepis clone bank, consisting of 116 clones, for three years. The between-year variation was large; i.e. the percentage of flowering grafts and average number of flowering per graft were $28.4{\sim}67.2$ and $9{\sim}176$, respectively. Differences in flowering abundance among clones were large and statistically significant in all the years studied. The variance of flowering abundance among clones was increased when flowering was poor. The average of broad-sense heritability of flowering abundance was 0.52. The genetic gain(%G) was estimated at 57.4% when the upper 30% clones were selected. The clonal stability of flowering abundance was compared using average number of flowering and coefficient of variance value of each clone. The clones such as Gyeonggi 9(29), Kangwon 37(137), Chungnam 6(46), Chungnam 14(414), R11, R8 showed abundant flowering and high stability.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.14-34
• /
• 1985

One of the techniques for altering the properties of wood that has received considerable attention in the last twenty years is the formation of a wood-polymer composite (WPC) by irradiation and heat-catalyst polymerization of a monomer incorporated into the wood matrix. Wood-polymer composites are the new products having the superior mechanical and physical properties and the combinated characteristics of wood and plastic. The purpose of this experiment was to obtain the basic data for the improvement of wooden materials by manufacturing WPC and Staypak. The species examined was Hyunsasi-Namoo (Populus alba ${\times}$ P. glandulosa) which had not been utilized yet. Methylmethacrylate (MMA) as monomer, benzoyl peroxide (BPO) as initiator and methyl alcohol as bulking agent were used. The monomer containing BPO was impregnated into wood pieces by the dipping and the vacuum process for 2 hours. After impregnation, the treated samples were polymerized on the hot press with pressure and heat-catalyst methods. The results obtained were summarized as follows 1. The monomer loading into wood by the dipping process was 12.13 percent and 29.99 percent by the vacuum. The polymer loading into wood by the dipping process was 6.79 percent and 15.44 percent by the vacuum. 2. Comparing with Staypak, antishrink efficiency (ASE) of WPC was 12.5 to 13.6 percent on the radial direction and 14.70 to 18.63 percent on the tangential. Antiswelling efficiency (AE) was 14.40 to 17.22 percent on the radial direction and 17.18 to 42.1 8 to 42.14 percent on the tangential. Reduction in water absorptivity (RWA) was 8.19 to 15.5 percent. As a whole, the vacuum process was better than the dipping. 3. The specific gravity of control, Staypak and WPC were 0.44, 0.66 and 0.61 to 0.62, respectively. 4. In the bending strength test, the strength in case that the load direction is on the radial surface was greater than that which the load direction is on the tangential. 5. Increasing rate of stress at proportional limit in compression perpendicular to grain was 72.26 percent in case of WPC by the dipping process, 78.93 percent by the vacuum and 99.09 percent in case of Staypak.