• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.233-244
• /
• 1997

구조적으로 손상을 입은 구조물들에 대한 보강방법으로 강판, 카본쉬트, 아라미드섬유쉬트 등을 이용한 접착공법이 최근 들어 많이 사용되고 있으며 그 중 가장 널리 Tm이는 방법은 강판접착공법이다. 강판접착공법에 대해서는 많은 연구가 진행되어 오고 있으나, 보의 구조적 거동에 영향을 미치는 다양한 인자들의 영향이나 강성, 파괴양상등에 미치는 영향들에 대해서는 체계적인 평가가 이루어지지 않은 실정이며 특히 강판접착공법에서 파괴에 큰 영향을 미치는 박리하중에 대한 연구는 미흡한 실정이다. 따라서 본 연구에서는 일련의 철근콘크리트보부재를 대상으로 하여 주요실험변수로 선행하중의 크기, 강판의길이, 강판의 두께, 앵커볼트의 간격과 유무, 강판의 층수, 측면보강높이를 실험변수로 하여, 휨인장에 대해 강판잡착공법을 적용하여 포괄적인 실험을 수행하였다. 3등분점하중법의 실험결과를 이용하여 처짐, 인장 및 압축 철근의 변형도, 콘크리트와 강판의 변형도를 분석하였고, 이를 토대로 파괴양상과 파괴하중을 분석하였다.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.5
• /
• pp.455-463
• /
• 2010

This paper describes the experimental study on the mechanical characteristics of a steel plate-reinforced concrete joint. As an alternative reinforced concrete structure, the SC modular construction method is widely used and studied in the field ofindustrial facility field. However, the structure characteristics of RC and SC joint are not yet studied completely. In this paper, the beam-type construction joint of RC and SC walls was made to simulate the application of SC module to the large RC structure. Also, an out-of-plane loading was applied to the test specimen in order to evaluate flexural strength and structural properties of the beam-type RC-SC joint.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.165-175
• /
• 1997

실제구조물의 균열을 노치를 삽입하는 방법으로 시뮬레이션하고 콘크리트 강도와 철근비를 변수로하는 실험적 연구를 통하여 철근콘크리트 보의 강판접착에 의한 보강효과를 규명하였다. 보강철근비와 보강된 보의 최대내력과의 관계를 회귀식을 통하여 제안하고 강판보강도니 보의 최대내력과 연성측면에서 구조적 거동을 고찰하였으며 최대내력시까지 외부강판과 철근콘크리트 보의 합성작용이 유지되는 것을 확인하였다. 또한 노치에 의하여 시뮬레이션된 균열의 영향을 고려하여 강판보강된 철근콘크리트 보의 휨강성을 평가하도록 실험결과를 회귀분석하여 실험식을 제안하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.6
• /
• pp.479-484
• /
• 2017

In this paper, finite element analysis of Steel-Concrete panel(SCP) was conducted considering the local buckling behavior and the optimized design of shear studs arrangement was studied by comparing with design guidelines. If the spacing of the studs of SCP is widened, it is easy to be manufactured and the weight fo members become lighter. On the other hand, the steel plate would be vulnerable to the local buckling behavior. Therefore, the guidance and design of SCP limit the maximum spacing of the studs to prevent the development of shear cracks and local buckling, however this is based on the design criteria of the other composite structures. Parameter studies with changes in stud spacing on steel plate and SCP are conducted and the obtained result was compared with values given in design guidelines.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.443-450
• /
• 2009

This paper describes the experimental study that was conducted on the temperature characteristic and bending capacity of a steel-plate-reinforced concrete-wall module (SC module). The steel plate ratio and temperature loading parameters were tested, and the influence of these parameters on the moment-curvature relationship and on the bending strength of the SC module was investigated. The fundamental-structure characteristic result of every SC module that assumed practical use was investigated. In this study, the bending and flexural characteristics of SC structures were evaluated to verify the yielding and ultimate strength of the SC beam under thermal-loading conditions.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.2
• /
• pp.269-278
• /
• 2008

The primary object of the paper is to understand the compressive buckling characteristics of steel-concrete structures through the finite element analysis. The buckling pattern, compressive strength and stiffness of the steel plate concrete structures were investigated by the FEM analysis using the variations of B/t ratios and stud pitches. The investigation was focused on steel plate concrete structures with and without ribs placed on the surface of steel plates. The results of the FEM analysis were compared with the previous results from the theoretical equations. Conclusively, the buckling of the steel plate concrete structures occurred in the transverse direction of the loading direction. The stiffness of the steel plate concrete structure with ribs is greater than the one without the stiffened rib. The compressive strength in the FEM analysis is similar to that of JEAG 4681 and it showed 20% greater value than that of the proposed equations.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.4
• /
• pp.549-559
• /
• 2008

The objective of this paper is to identify the compression forces and inelastic failure mode using stiffened steel plate-concrete structures. The compression tests were carried out for the three types of B/t ratios by 25, 33 and 50. The test results proved that the compressive strength of the stiffened SC structures can be estimated by the summation of the strengths both stiffened steel plate and concrete. The buckling of the steel plates had been occurred at the plates between studs. The empirical estimation of compressive strength for the stiffened SC structures under compressive loadings was suggested. The buckling behavior also compared with the results of the finite element analysis. The good agreement has been achieved between the experimental results and finite element results.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.41.1-41.1
• /
• 2010

복부 파형강판 PSC 박스거더는 상부와 하부에 콘크리트 슬래브를 갖고 있으며, 복부에만 강판이 사용되는 특수한 형태의 교량이다. 해당 형식의 비틀림 거동을 이해하기 위해서는 상, 하부 콘크리트의 비틀림 거동에 대해 먼저 분석한 후, 비틀림에 의한 전단변형률이 거더 단면의 모든 구간에서 동일하다는 적합조건을 이용하여 복부의 비틀림 거동을 이해해야 한다. 기존의 복부 파형강판을 갖는 PSC 박스거더에 대한 연구는 전단거동(Easley, 1969; Elgaaly et al., 1996; 문지호 외, 2004; 이종원 외, 2005) 및 휨 거동(Elgaaly et al., 1997; Abbas et al., 2006, 2007; 문지호 외 2008)에 대하여 수행되어 왔으며, 이러한 연구들은 파형강판 자체에 국한되는 경향이 있다. 특히나 전체 복합거더의 비틀림 거동에 대한 연구는 크게 부족한 상황이며, 기존의 연구(Mo et al., 2000)는 균열 발생 이후의 비틀림 거동에 대해서만 수행되었고, 슬래브가 갖는 인장 강도를 무시하였다. 본 연구에서는 콘크리트의 비틀림 발생 이전과 이후를 모두 예측할 수 있는 방법을 제안하였고, 이를 토대로 시행오차법이 적용된 해석 알고리즘을 제작하였으며, 유한요소해석을 통하여 검증하였다.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.3
• /
• pp.129-138
• /
• 2016

Buckling of surface plates is an important limit state in Steel-Plate Concrete (SC) walls under axial compression. The surface plates may be anchored to concrete using connectors of studs or tie-bars. In this paper, the effects of studs and tie-bars on buckling of surface plates were evaluated by conducting tests. Experiments have three types of connectors; all studs, all tie-bars, and the combination of studs and tie-bars. Also, experiments have the various ratios of stud or tie-bar spacing to surface plate thickness. The experimental investigation shows that the buckling shape and strength of the surface plate of SC wall with the combination of studs and tie-bars have good agreements with that of the surface plate of SC walls with all studs or all tie-bars.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.4
• /
• pp.561-570
• /
• 2008

The primary object of the paper is to identify the compression forces and inelastic failure behavior using steel plate-concrete structures. The compression tests were carried out for the three types of B/tratios by 25, 33 and 50. The tests proved that the compressive strength of the SC structures can be estimated by the summation of strengths both of the steel plate and concrete. The buckling of the steel plates had been occurring at the plates between studs. The empirical estimation of compressive strength for unstiffened SC structures under compressive loadings was suggested. The buckling behavior was also compared with the results of the finite element analysis.