• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.248-254
• /
• 2014

The purpose of this study is to develope a control system for a small X-ray tube generator and investigate control methods for the X-ray generator. The small X-ray tube was developed for electronic brachytherapy, and thus, the new control method should be investigated, if the small X-ray tube is used for the imaging system. The Axxent S700 X-ray tube and the XF060NZZ485 high voltage generator were used to compose a X-ray imaging system and control board was developed by using AT90CAN128 MCU. The two control methods were investigated after tube voltage was set to 50 kV, one was filament current control method and the other was beam current control method. The former was subdivided into two methods according to the filament heating time, the 5 and the 10 seconds respectively. In the filament current method, the beam current did not rise up to the desired value, if the filament current had not been maintained for at least 10 seconds. The onset filament currents to generate beam current were varied from 1,300 to 1,350 mA and over 5 seconds were needed in order to reach the desired tube current value after beam current was generated. However, in the tube current control method, the beam current reached to the desired value without any time delay with the filament current of 1,500 mA. In this study, we found that the beam current control method was appropriate for the use of small X-ray tube developed for brachytherapy in the X-ray imaging system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.5
• /
• pp.335-342
• /
• 2013

Since the seriousness of environmental pollution came to the fore recently, various efforts have been made globally for the reduction of the environmental load. In particular, in the field of construction, an industry responsible for a considerable amount of pollution, studies have been actively conducted to reduce $CO_2$ emissions and energy consumption. However, most conventional research about pollution as it relates to construction is focused on the maintenance stages where $CO_2$ emissions are the greatest. Research related to the design stage is in its infancy, as it has only been conducted thus far on steel buildings and RC buildings. In fact, in order to achieve environmentally friendly construction considering the Life Cycle Assessment(LCA), the building design should be derived to reduce the $CO_2$ emissions from the early building design stage, and structural engineers should be able to suggest a design plan considering its environmental friendliness. In this study, optimal structural design method for steel reinforced concrete(SRC) columns considering $CO_2$ emissions is presented. The trends of $CO_2$ emissions in SRC columns according to the variations of steel shapes, concrete strengths and loads are investigated.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.6
• /
• pp.899-903
• /
• 2005

One of the most important volatile aroma compounds responsible for mushroom flavor is 1-octen-3-ol. To meet the demand for natural mushroom flavor, a study was needed for the production of natural chiral specific (-)-1-octen-3-ol that has higher flavor intensity than synthetic chiral mixtures of (+), and (-)-1-octen-3-ol. The biosynthesis of (-)-1-octen-3-ol was achieved by an aerobic oxidation using lipoxygenase (LOX) and hydroperoxide lyase (HPOL) isolated from commercially available mushrooms in Korean market. Safflower oil from Uiseong, Gyeongsangbuk-do, that contains $\geq75\%$ of linoleic acid, was hydrolyzed using lipase. The recovered linoleic acid was biotransformed to stereo-specific 10-hydroperoxy linoleic acid by LOX. 10- hydroperoxy linoleic acid was further cleaved to (-)-1-octen-3-ol by HPOL. A commercial bioprocess for the production of (-)-1-octen-3-ol was developed using a 5-liter jar fermenter with fruiting bodies of Agaricus bisporus harvested from Buyeo, Chungcheongnam-do. The maximum production of (-)-1-octen-3-o1 was achieved at $4^{\circ}C$, pH 6.5 and 800 rpm yielding 748 mg/kg of mushroom.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.366-372
• /
• 2005

This paper presents analysis of a slot array antenna having a low side lobe level and high front-to-back ratio for a repeater system of a satellite DMB(Digital Multimedia Broadcasting) service. Antennas for this repeater system require a high gain and enough isolation to reduce interferences between signals in system. Therefore, it is necessary to suppress a side lobe level and to increase front-to-back ratio. Unlike a structure 134 by lossy microstrip lines, in this work a single cavity-backed slot antenna array using a single waveguide feed is proposed to obtain the reliability for high power handling and high radiation efficiency. The side lobe level and front-to-back ratio are enhanced with tapered array technique and an optimized vertical reflector. The measured side lobe levels in H- and E-plane are under $-33.24\;\cal{dB}$ and $-35.78\;\cal{dB}$, respectively. The front-to-back ratio over $37.84\;\cal{dB}$, and the peak gain of over $17\;\cal{dBi}$ are measured.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1824-1832
• /
• 2011

In this paper, a smart home service robot McBot II is newly developed in much more practical and intelligent system than McBot I which we had developed a few years ago. Thus far, vacuum-cleaners have lightened the burden of household chores but the operational labor that vacuum-cleaners entail has been very severe. Recently, a cleaning robot was commercialized to solve but it also was not successful because it still had the problem of mess-cleanup, which pertained to the clean-up of large trash and the arrangement of newspapers, clothes, etc. Hence, we develop a new home mess-cleanup robot McBot II to completely overcome this problem on real environments. The mechanical design and the basic control of McBot II, which performs mess-cleanup function etc. in house, is actually focused in this paper. McBot II is mechanically modeled in the same method that the human works in door by using the waist and the hands. The big-ranged vertical lift and the shoulder joints to be able to forward move are mechanically designed for the operating function as the human's waist when the robot works. The mobility of McBot II is designed in the holonomic mobile robot for the collision avoidance of obstacle and the high speed navigation on the small area in door. Finally, good performance of McBot II, which has been optimally desinged, is confirmed through the experimental results for the control of the robotic body, mobility, arms and hands in this paper.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.2
• /
• pp.414-421
• /
• 2015

This paper presents a new method to decompose a duplicated ECG signal, which is measured from two people, to two individual ECG signals. In paper, it is shown that the duplicated ECG signal can be decomposed, provided that their SAECG signals are known. As the SAECG signal is the average of a ECG signal, it is a feature to identify individual ECG signals from the duplicated signal. Since the ECG signal is nearly periodic, so-called heart-rate, the period of each ECG signal can be found by using the autocorrelation of the duplicated signal, That is, the autocorrelation has high peaks at the multiple instants of heart-rate of each person. With the heart-rate of each person obtained by some processing, all R-peaks are identified by the SAECG signals. To be concrete, the SAECG signal of each person is repeatedly placed at the R-peak instants with his heart-rate, and the weight of each SAECG signal is computed by LMSE optimization. Finally, as adding the error signal in the LMSE optimization processing to the weighted SAECG signal, each individual ECG signal is obtained. In experimental results, we demonstrate that the duplicated ECG signal is successfully decomposed into two ECG signals.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.116-116
• /
• 2007

21 세기에 접어들면서 인터넷을 통한 정보 통신의 발달과 개인 휴대용 이동 통신기기의 활발한 보급에 따라 휴대형 전자기기들의 소형화와 고성능화로 나아가고 있다. 이러한 전자기기에 사용될 IC의 내장 메모리 또한 집적화 및 고속화, 저 전력화가 이루어져야 한다. 이러한 전자기기들에 필수적인 압전 세라믹스 부품 중 압전 부저 및 기타 음향 부품등을 각종 전자기기와 무선 전화기에 채택함으로써 압전 부품에 대한 수요와 생산이 계속 증가할 것으로 전망된다. 이처럼 압전 세라믹스를 이용한 그 응용 범위는 대단히 방대하며, 현재 모든 압전 부품들은 PZT 계열 재료로 만들어지고 있고, 차후 모두 비납계열 재료로 대체될 것이 확실시된다. Pb의 환경오염은 이미 오래전부터 큰 문제점으로 인식되고 있었으며 그 일례로 미국의 캘리포니아 주에서는 1986년부터 약 800종의 유해물질, 그 중에서도 Pb 사용을 300ppm 이하로 규제하는 Proposition 65를 제정하여 실행하고 있다. 그리고 2003년 2월에 EU (European Union) 에서 발표한 전자산업에 관한 규제 사항중 하나인 위험물질 사용에 관한 지칭 (Restriction of Hazardous Substance, RoHS) 에 의하면, 2006 년 7월부터 전기 전자 제품에 있어서 위험 물질인 Pb을 포함한 중금속 물질(카드늄, 수은, 6가 크롬, 브롬계 난연재)의 사용을 금지한다고 발표하였다. 비록 전자세라믹 부품에 함유된 Pb는 예외 사항으로 두었지만 대체 가능한 물질이 개발되면 전자세라믹 부품에서도 Pb의 사용을 금지한다고 규정하였다. 더욱이 일본은 2005 년부터 Pb 사용을 금지시켰다. 이와 같이 Pb가 환경에 미치는 영향 때문에 비납계 강유전 물질 및 압전 세라믹스 재료에 대한 연구가 전 세계적으로 활발히 진행되고 있다. 본 연구에서는 비납계 강유전체의 patterning을 위해서, NKN 박막을 고밀도 플라즈마원인 ICP를 이용하여 식각 mechanism을 연구하고, 식각변수에 따른 식각 공정을 최적화에 대하여 연구하였다. 가스 혼합비에 따라 식각 할때 700 W의 RF 전력과 - 150 V의 직류 바이어스 전압을 인가하였고, 공정 압력은 2 Pa, 기판 온도는 $23^{\circ}C$로 고정하였다. 식각 속도는 Tencor사의 Alpha-step 500을 이용하여 측정되었으며 식각 시 NKN 박막 표면과 라디칼과의 화학적인 반응을 분석하고 식각 메커니즘을 규명하기 위하여 XPS(x-ray photoelectron spectroscopy)를 사용하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.1
• /
• pp.113-119
• /
• 2013

Despite rapid changes in the structure of industry, manufacturing remains a key industry for economic progress, promotion of trade, increased employment, and the creation of new industries. Production technologies are essential for strengthening the competitiveness of small- and medium-sized manufacturing industries. However, it is very difficult to standardize and systematically propagate production technology from an experienced worker to an inexperienced worker because these technologies are generally improved by the skilled people in a workshop. In this study, we introduce a Web-based platform system consisting of a knowledge authoring tool, technology database, semantic database, and Web portal service for sharing production technologies for the exterior housing parts of mobile products. By investigating various cellular phone designs, reference form factors for three types of mobile phone housings were designed based on the standard features. In addition, several manufacturing technologies and considerable information such as reference mold designs and molding conditions optimized using CAE and recent R&D outputs are stored in this system.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.800-808
• /
• 2005

The compounding resin for biodegradable wrap was developed, and its manufacturing process and physical properties were studied. For these purposes, following factors were optimized: the types and amounts of raw resin material, anti-oxidants, and lubricants used. In this work, the stable compounding resin used to make biodegradable wrap was based on poly(butylene adipate-co-butylenesuccinate) (PBAS) and poly(butyleneadipate-co-butylene succinate-co-butyleneterephthalate) (PBAST). The improved properties of resin with an additive were investigated by melting flow index (MFI). From these results, the physical properties of compounding resin, based on PBAST, were more than those of PBAS. For PBAS, the Irganox 1010, 1076 and Irgafos TNPP as the first and second anti-oxidants, respectively, were good. For PBAST, the good first and second anti-oxidants, respectively, were Irganox 1076 and Mark PEP 36. The good lubricants for feeding PBAS and PBAST were glycerol monostearate and palmityl alcohol, respectively. The stability and tensile strength experiment of wrap were also investigated by the elution of heavy metals and universal testing machine (UTM), respectively. The decomposition ratio of developed wrap was increased proportional to the reclaiming time. The degradation ratio of compounding resin sample was about 60% after 40 days.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2001.04b
• /
• pp.100-102
• /
• 2001

본 연구에서는 온실의 난방에 사용되는 열풍식 난방기 등의 배기 연통에 부착하여 배출되는 가스로부터 열을 회수할 수 있는 장치를 개발함에 있어서 연통과 열회수 장치간의 열 교환 성능을 3가지 상이하게 설계된 열 교환 장치(Fig. 1 참조)에 대하여 실험적으로 비교 분석하였다. Fig. 1-(a)는 열 교회수기 개발을 위해 기존에 사용한 장치로서 회수용 공기의 흐름방향이 배기 연통과 직각을 이룬 형식이며, Fig. 1-(b) 및 (c)는 열 회수 성능 개선을 위해 새로 설계된 형식으로서 각각 열 교환 파이프의 배치형식이 상이하나 회수용 공기의 흐름방향이 180도로 굴곡되는 U-자형 흐름이 이루어지도록 하였다. 실험에 사용된 공기 순환 펜의 용량은 AB-형의 경우에는 최대 25㎥/min이고, C-형 및 D-형의 경우는 공히 최대 42㎥/min으로서 송풍전압 조절장치를 이용하여 풍량을 연속적으로 조절할 수 있도록 하였다. U-자형 흐름형식인 C-형 및 D-형의 경우 흐름 방향의 굴곡으로 인한 마찰저항이 있을 것으로 예상은 했으나 당초 예상했던 것에 비해 마찰 저항이 지나치게 큰 것으로 밝혀졌다. 비록 설계된 열교환 튜브의 배열형식별 열 교환기의 외부 모양이 달라 회수기의 표면을 통한 대류 열 교환이 다소 차이를 보일 것으로 예상되지만 본 연구에서는 열 회수장치에 내장된 열 교환 튜브부분만을 통한 열 회수율을 중심으로 형식간의 성능을 비교하였다. 실험을 통하여 측정된 자료중 대표적인 예는 Fig-2와 같으며, 측정자료를 기준으로 분석된 열회수 성능에 대한 설계형식별 비교 결과는 Table-1과 같으며, 분석된 결과를 요약하면 다음과 같다: 1. AB-형 열회수시스템의 경우, 초기 투자비용과 현재의 농용 전력요금 하에서 에너지 절감규모를 비교하면, 대체로 1년을 전후하여 투자에 대한 보상이 충분히 가능할 것으로 판단된다. 2. C-형 및 D-형 열회수시스템의 경우, 열 회수용 공기의 흐름방향이 동일 공간내에서 180도 굴절됨으로서 저항이 크게 발생되어 송풍 펜의 전압 증가에 따른 유속증가가 미미하였으며, 굴절형의 열교환장치는 비록 열교환면적은 직선형과 유사하더라도 송풍 펜의 공기저항이 커져서 결국 열 회수성능이 기대했던 것만큼 크게 개선되지는 못했다. 3. 송풍펜의 용량은 AB-형에 사용된 용량인 25㎥/min 전후가 적절할 것으로 판단되며, 적정 송풍 펜용량 하에서 열 회수성능은 굴절형이 직선형보다 효과적인 것으로 나타났다. 다만, 곡선형은 물론 직선형에서도 열교환 튜브의 배치밀도, 튜브 길이 및 두께 등의 변화에 따른 최적화 연구가 수반되어야 할 것으로 판단된다.