• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.2
• /
• pp.58-67
• /
• 1995

The paper describes the variation of magnetic fields caused by the operation of induction motors. The measuring system consists of the self-integrating magnetic field sensor, amplifier, and active integrator. From the calibration experiments, the frequency bandwidth of the magnetic field measuring system ranges from 20[Hz] to 300[kHz] and sensitivity is 0.234(mV/$\mu\textrm{T}$]. The magnetic fields generated under steady state and starting operations of duction motor are recorded by the proposed measuring system, and the fast Fourier transformation(FFT) of the measured data is performed to analyze the harmonic components. A single pulsed magnetic field is strongly caused by direct starting the induction motor, and its peak value is greater than 5 times as compared with the steady state value. The long transient duration and high intensity originates from the large inductance and dynamic characteristic of the induction motor, During the steady state operation of induction motor, subharmonics of magnetic field components, which depend on the pole number of induction motor, are observed. The lower order power-line harmonics can be inferred from the voltage flicker and current ripple which are derived from the torque fluctuation of induction motor. In the case of the induction motor drived by inverter, the harmonics of magnetic field are much more than those caused by direct starting method and are found generally to increase with decreasing the driving frequency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.9
• /
• pp.815-820
• /
• 2016

An elastic polymer (e.g., PDMS) blended with EFG particles is a promising conductive composite for fabricating soft sensors that can detect an object's deformation up to or more than 50%. Here, we develop large-strain, sprayable soft sensors using a mixture of PDMS and EFG particles, which are used as a host elastomer and electrically conductive particles, respectively. A solution for a conductive composite mixture is prepared by the microwave-assisted graphite exfoliation, followed by ultrasonication-induced fragmentation of the exfoliated graphite and ultrasonic blending of PDMS and EFG. Using the prepared solutions for composite and pure PDMS, 1-, 2-, and 3-axis soft sensors are fabricated by airbrush stencil technique where composite mixture and pure PDMS are materials for sensing and insulating layers, respectively. We characterize the soft strain sensors after investigating the effect of PDMS/EFG wt% on mechanical compliance and electrical conductance of the conductive composite.

• Journal of the Korean Magnetics Society
• /
• v.16 no.6
• /
• pp.279-282
• /
• 2006

Magnetic tunnel junctions (MTJs), which consisted of amorphous ferromagnetic NiFeSiB free layers, were investigated. The NiFeSiB layers were used to substitute for the traditionally used CoFe and/or NiFe layers with the emphasis being given to obtaining an understanding of the effect of the amorphous free layer on the switching characteristics of the MTJs. $Ni_{16}Fe_{62}Si_{8}B_{14}$ has a lower saturation magnetization ($M_{s}:\;800\;emu/cm^{3}$) than $Co_{90}Fe_{10}$ and a higher anisotropy constant ($K_{u}:\;2700\;erg/cm^{3}$) than $Ni_{80}Fe_{20}$. The $Si/SiO_{2}/Ta$ 45/Ru 9.5/IrMn 10/CoFe $7/AlO_{x}/CoFeSiB\;(t)/Ru\;60\;(in\;nanometers)$structure was found to be beneficial for the switching characteristics of the MTJ, leading to a reduction in the coercivity ($H_{c}$) and an increase in the sensitivity resulted from its lower saturation magnetization and higher uniaxial anisotropy. Furthermore, by inserting a very thin CoFe layer at the tunnel barrier/NiFeSiB interface, the TMR ratio and switching squareness were improved more with the increase of NiFeSiB layer thickness up to 11 nm.

• Journal of the Korean Magnetics Society
• /
• v.16 no.2
• /
• pp.140-143
• /
• 2006

Single crystalline $CoFe_2O_4$ thin films on (100) MgO substrates were fabricated using a rf magnetron sputtering method. The deposited films were investigated for their crystallization by X-ray diffraction, Rutherford back-scattering spectroscopy and field emission scanning electron microscopy. When a cobalt ferrite film was deposited at the substrate temperature of $600^{\circ}C$, squared grains of about 200 nm were uniformly distributed in the film. However, the grains became irregular and their sizes also varied from 30 to 150 nm when the substrate temperature was $700^{\circ}C$. Hysteresis loops of a film deposited at $600^{\circ}C$ showed that the magnetically easy axis of the film was perpendicular to the substrate surface. Except for the squareness ratio, magnetic properties of the cobalt ferrite films grown by the present rf sputtering method were as good as those of the films prepared by a laser ablation method: The in-plane and perpendicular coercivities were 283 and 6800 Oe, respectively. As the thickness of the deposited film increased twice, the saturation magnetization became double but the coercivity remained unchanged. However, deposition of the Co ferrite films with a higher rf powder decreased the squareness ratio and the perpendicular coercivity of the films.

• Membrane Journal
• /
• v.15 no.4
• /
• pp.297-309
• /
• 2005

As a number of potential endocrine disrupting compounds (EDCs) are released into the environment, recently growing attention has been drawn to them. Therefore sensitive and reliable analytical methods are essential to monitor those compounds. In this study, complementary CC-MS and LC-MS were employed to analyze the endocrine disrupters, and the results of two methods were compared for di(2-ethylhexyl)phthalate (DEHP), benzylbutylphthalate (BBP), pentachlorophenol (PCP), and 4,4'-Isopropylidenediphenol (Bisphenol-A, or BPA). The results indicate that it was possible to lower the detection limits of EDCs by LC-MS. Also, LC-MS enabled to identify the EDCs as almost intact molecules. Furthermore, this study presented a nanofiltration membrane (MWCO 250) and a ultrafiltration membrane (MWCO 1,000) filtration system as methods far removing EDCs from drinking water containing $\gamma$-BHC, p,p'-DDE, BBP, p,p'-DDT, DEHP, PCP, and BPA. Cross-flow type nanofiltrations showed $100\%$ removal of EDCs, and the result implies that MWCO 250 nanofilter was sufficient for treatment of EDCs. The ratio of permeate flux to mass transfer coefficient of nanofiltration, high flux ultrafiltration, and low flux ultrafiltration with ultrapure water were 0.67, 3.4, and 0.44, respectively. It was found that nanofiltration and low flux ultrafiltration were operated at a diffusion dominant condition, and the high flux ultrafiltration was operated at a convection dominant condition. Furthermore, a diffusion dominant process attained reasonable rejection of EDCs. The removal in the ultrafiltration was depending on the molecular weight of an EDC, and the filtration was governed by diffusion-dominant hydrodynamic conditions.

• Korean Journal of Food Science and Technology
• /
• v.30 no.6
• /
• pp.1273-1278
• /
• 1998

Conditions for enzyme-protein binding assay (EPBA) were established in order to detect biotin more rapidly and reproducibly than traditional microbiological assay (MBA). EPBA with streptavidin and biotin-KLH conjugate showed cross-reactivities on biocytin, a derivative with biotin activity, at the rate of 109% $(IC_{50}=0.3\;ppb)\;and\;197%\;(IC_{50}=0.8\;ppb)$, respectively, but not on other derivatives with no biotin activities, such as desthiobiotin, diaminobiotin and 2-iminobiotin. Detection ranges of biotin by EPBA with streptavidin and biotin-KLH conjugates were $0.01{\sim}30\;ng/mL\;and\;0.01{\sim}1.0\;ng/mL(ppb)$, respectively. In the spike test with milk, fruit flake and pine-carrot juice, the correlation coefficience between MBA and EPBA with biotin-KLH conjugates was r=0.994. But MBA showed cross-reactivities both on biocytin and desthiobiotin at the rate of 80.1% and 66.7%, respectively. Detection range of biotin by MBA was $0.1{\sim}0.5\;ng/mL(ppb)$. These results strongly suggest that EPBA is efficient for biotin detection in sensitivity, detection range, cross-reactivity and time consuming.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.60-60
• /
• 1998

아연도금강판은 내식성이 우수하여 자동차용 강판으로 널리 쓰이고 있다. 자동차용 강판은 spot 용접에 의해서 각 부분들이 접합되는데 도금층으로 사용되는 아연은 강판보다 융점이 낮아서 용접작업을 저하시킨다. 현재 사용되는 작업조건에서 용접 타 접수가 평균 2000회를 넘게되면 용접되는 부위의 면적이 감소되어 접합강도가 떨어지게된다. 따라서, 아연이 도금된 강판을 용접하게되면 작업성이 저하되므로 도금층의 성분에 대한 변화를 주므로서 이에 대한 개선을 할 필요가 있다.. Cole, Dickenson 및 Kimchi 등은 도금충내의 알루미늄을 0.1~0.5%(중량비) 함유하는 아연도금강판은 저항용접시 도금충내의 알루미늄 함량에 따라 용접성이 영향을 받는다고 보고하였다. 전극수명은 도금층내의 알루미늄 함량이 증가할수록 떨어지는데 알루미늄이 0.5% 이 하로 함유된 아연도금강판의 경우는 용접타접수가 2000~6000회에 이르르나 알루미늄 이 50%이상 함유된 합금도금강판은 200-600회에 불과한 것으로 나타난다. H. M Matsuda 등은 도금층의 알루미늄이 용접성에 영향을 미치는 이유로서 도금층의 용융 온도 변화를 지적하였다. 도금충내에 알루미늄의 함량이 높게되면 철과 아연의 확산에 의한 합금화 반응이 저하되어 도금층의 용융온도가 높아지지 못하므로 용접성이 나빠지게 된다. 본 연구에서는 아연도금욕의 조성은 기존의 상태로 유지하고 제3의 원소를 첨가하여 도금층에 함유되는 알루미늄의 양에 미치는 효과를 조사하였다. 도금층의 불성변화 및 그에 따른 내식성을 조사하였으며 도금층의 조직변화도 함께 관찰하였다. 아울러 첨가원소에 의한 도금욕의 특성도 평가하였다. 첨가원소에 의해서 도금충내의 알루미늄 함량은 감소하는 경향을 나타내었으며 도금층의 물성은 주어진 조성범위 내에서 별다른 변화를 나타내지 않았다.brittlement)기구도 제안되고 었다. 원전의 냉각수는 고 순도의 물이지만 수 처리 과정과 웅축기 배관의 누수로 인한 산소, $Cu^{2+},{\;}S_xO_6{\;}^{2-}(x=3~6)$ 등이 유입되어 오염되는데 이려한 오염물질들이 수 ppm정도 소량 포함된 경우 응 력부식민감도는 상당히 증가된다. 산성분위기 흑은 산소, $Cu^{2+}$, 등이 소량 포합된 산화성 분위기 그리고 sufur oxyanion 에 오염된 고온의 물에서 600 의 IGSCC 민감도는 예민화도가 증가할 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.369-375
• /
• 1997

$V_{2}O_{5}/ThO_{2}/Pd$-doped $SnO_{2}$ sensor has a good selectivity and stability to CO at high sensor temperature of about $500^{\circ}C$, and shows rapid response. In particular, many kinds of interference gases, such as $NO_{x}$, $C_{3}H_{8}$, $CH_{4}$ and $SO_{2}$ have been found to give only a slight influence on the sensor selectivity to CO gas sensitivity by doped $V_{2}O_{5}$ (3.0 wt.%). For the sensor we used well-known thick film technological route with $V_{2}O_{5}$(3.0 wt.%), Pd(1.0 wt.%) and $ThO_{2}$(l.5 wt.%) as catalytic materials. In the case of mixed $NO_{x}$-CO gases, as combustion exhaust gas, only CO detection by $SnO_{2}$ type semiconductor sensor is generally very difficult because of $NO_{x}$ interference. The developed sensors can use to measure the exhausting gas of the automobile or the boiler for the Air-to-Fuel ratio control.

• The Korean Journal of Pesticide Science
• /
• v.9 no.4
• /
• pp.292-302
• /
• 2005

Condition of Ion-Trap gas chromatography-mass spectrometry (GC-MS) for rapid screening of 206-pesticides residues in agricultural foodstuffs was optimized. As applying a wide-bore column (10 m${\times}$0.53 mm, DF 0.25 um) connected with a fused silica restrictor (0.6 m${\times}$0.1 mm), a significant retention time reduction was obtained. Additionally, the shape of peaks was sharper and higher than classical GC's and GC-MS's, which allowed lower detection limits. To easily manage many spectral data, both of Electron Ionization(EI) and Chemical Ionization(CI) techniques were adopted in screening procedure. At the following steps, MS-MS technique were used to confirm screened analytes in complicated matrices.

• Journal of radiological science and technology
• /
• v.28 no.1
• /
• pp.1-7
• /
• 2005

High-quality single crystals of pure $Li_2B_4O_7$ as well as $Li_2B_4O_7$ doped with Cu, Mn and Mg impurities (1.0mol%, respectively) have been grown from the melt of $Li_2CO_3+2B_2O_3$ by Czochralski method in platinum crucibles. To study the thermoluminescent properties, $Li_2B_4O_7$ series single crystal TLDs were made by cutting in the size of $4{\times}5{\times}1\;mm^3$. The glow curves show two or three peaks which can be easily deconvoluted. It is observed that room temperature($20{\sim}30^{\circ}C$) fadings of the dosimetric peaks of $Li_2B_4O_7$ series single crystal TLDs were about 10 % for 30 days. The relative photon energy response for $Li_2B_4O_7$ series single crystal TLDs were about 85 % when the responses were normalized to that measured with $^{60}Co\;(1.25\;MeV)\;{\gamma}-rays$. The measured data are in a good agreement with theoretical ones. The $Li_2B_4O_7$ series single crystal TLDs fabricated in this work can be used for monitoring personal and environmental radioactivity.