• Elastomers and Composites
• /
• v.13 no.3
• /
• pp.197-206
• /
• 1978

반응속도면(反應速度面)에서의 동력학적(動力學的) 연구결과(硏究結果)에 의(依)하면 2-메르캅토벤쪼티아졸(MBT)은 N-t-부틸-벤쪼티아졸썰펜아미드(BBTS) 또는 2-(4-몰폴리노티오) 벤쪼티아졸(OBTS)과 같은 가황촉진제(加黃促進劑)들 보다는 N-(싸이클로헥실티오)프탈이미드(CPT)가 훨신 더 빨리 반응(反應)한다는 사실(事實)을 탐지(探知)하였다. 또한 우수(優秀)한 가황지연제(加黃遲延劑)는 MBT와 급속(急速)히 반응(反應)하여야 하지마는 실소(室素)와 황(黃)과의 화학결합(化學結合)이 너무 약(弱)하여 내열안정성(耐熱安定性)이 없음으로 아무리 MBT와 빠른 속도(速度)로 반응(反應)하여도 좋은 가황(加黃)지연제가 될 수는 없다. 예를들면 N-(싸이클로헥실티오-O-벤쪼의 썰펜이미드(CTBS))는 CTP보다 더 빨리 MBT와 반응(反應)하지만 열안정성(熱安定性)이 부족(不足)하여 가황(加黃)지연제로서는 CTB 보다 좋지 못하다.

• Applied Chemistry for Engineering
• /
• v.2 no.4
• /
• pp.356-362
• /
• 1991

The physico-mechanical properties of NR/BR blend were measured, and the results were interpreted in terms of the crosslink density with cure system. The cure rate, maximum torque and crosslink density increase with the content and ratio of curative for cure system. Hardness, 300 % tensile modulus, rebound and wear resistance increase with crosslink density of the vulcanizate but heat build-up and tan $\delta$ at $60^{\circ}C$ decrease. It is expected that semi-EV(efficient vulcanization) cure system is appropriate for application in tire tread of truck/bus in which load bearing property is impotant.

• Elastomers and Composites
• /
• v.42 no.2
• /
• pp.107-111
• /
• 2007

Adhesion of NR and BR composites with different initial states of precured or uncured conditions was studied. Adhesion between the NR and BR sheets as well as adhesion between the same rubber sheets was investigated. Adhesion forces of the uncured/uncured specimens were larger than those of the cured/uncured and cured/cured ones. The cured/cured samples and uncured NR/cured BR specimen were fully peeled out by the peel test. When one sheet was broken during the peel test, the sheet having the higher crosslink density was broken irrespective of the rubber types. Adhesion forces of the same rubber sheets were higher than those of the different ones and adhesion force of the cured NR/uncured BR sample was higher than that of the uncured NR/cured BR one. The experimental results were explained with the crosslink density and interdiffusion of rubber chains.

• Elastomers and Composites
• /
• v.40 no.3
• /
• pp.181-187
• /
• 2005

Changes of physical properties or NR vulcanizates with different cure systems by thermal aging were investigated. Two sulfur cure systems and one resole cure system were employed, and total contents of the curatives were varied. For the NR vulcanizates with sulfur cure systems, hardness and modulus after the thermal aging at $90^{\circ}C$ for 3 days were increased, but elongation at break and tensile strength were decreased. For the NR vulcanizates with resloe cure system, the physical properties after the thermal aging were decreased. The change of physical properties by the thermal aging was explained with the crosslink density change. The crosslink densities or the NR vulcanizates with sulfur cure systems were increased after the thermal aging, but those with resole cure system were decreased. Influence of the migration of antidegradant on the changes of physical properties was also investigated. However, the changes of physical properties by the thermal aging were not explained sufficiently with the migration of antigradant.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.403-409
• /
• 2009

In the 1840s, Goodyear found out sulfur cure system, but cure time was too slow. So producing of rubber product takes a long time. In 1904, Oenslager et al. found that aniline is accelerated sulfur cure system. Recently, many rubber industries needed high yield and good quality. So, many researchers have studied a rubber system with fast vulcanization time and good mechanical properties. In this study, cure characteristics and mechanical properties of NR/BR compounds by accelerator with MBTS(2,2' Dithiobisbenzothiazole), TMTM(Tetramethylthiuram Monosulfide), ZDMC (Zinc dimethyldithiocarbamate), CBS(N-Cyclohexyl benzothiazolyl-2-sulfenamide), DPG(Diphenylguanidine) were evaluated. The results of the study indicate that cure charateristics($t_{90}$: 235 sec, $T_{max}$: 5.77 Nm) and mechanical properties (100, 300% modulus : 2,180, 5.656 Mpa and tear strength: 59.58 kgf/cm) of NR/BR compounds shows efficient acceleration with MBTS 1.5 phr, TMTM 0.5 phr, DPG 0.15phr. This is due to the synergistic activity of ternary accelerator system in rubber vulcanization.

• Elastomers and Composites
• /
• v.13 no.2
• /
• pp.126-132
• /
• 1978

SBR 백색(白色) 배합(配合)고무의 일광변색(日光變色)은 노방제(老防劑)나 연화제(軟化劑)의 종류(種類)와 양(量)에 의(依)한 영향보다는 가황제(加黃劑)나 촉진제(促進劑)의 종류(種類)에 큰 영향을 받으며, 특(特)히 가황(加黃)의 정도(程度)는 변색(變色)에 가장 큰 영향을 미친다.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.37-43
• /
• 2001

Influence of the filler composition ratio on cure characteristics and bound rubber content of the compounds and on physical properties of the vulcanizates were studied using both silica and carbon black-filled styrene-butadiene rubber (SBR) compounds with the total filler content of 80.0 phr. The bound rubber content increased slightly with increase of the silica content ratio. The viscosity also increased with increasing the silica content ratio, especially increased steeply after the silica content of 60.0 phr. The cure times obtained with a rheometer, t2, t40, and t90, are increased by increasing the silica content ratio and the cure rate decreased. The delta torque increased with the increased silica content ratio. Variation or the modulus with the silica content ratio showed a decreased trend though the delta torque increased. The tan ${\delta}$ at $60^{\circ}C$ decreased with increased of the silica content ratio.

• Elastomers and Composites
• /
• v.42 no.2
• /
• pp.102-106
• /
• 2007

Water swelling behaviors of SBR vulcanizates with different reinforcing systems of carbon black, silica without a coupling agent, and silica containing a coupling agent were studied. Distilled water and 3.5% NaCl solution were used as swelling media. The water swelling ratios in the distilled water were higher than those in the salt solution. The water swelling ratios of the carbon black-filled samples were lower than those of the silica-filled ones. For the silica-filled SBR vulcanizates, the specimens without the silane coupling agent had higher water swelling ratios than those containing it. Water swelling behaviors of SBR composites with different 1,2-unit contents were also compared. The water swelling ratios tended to decrease by increasing the 1,2-unit content.

• Journal of the Korean Chemical Society
• /
• v.41 no.10
• /
• pp.524-534
• /
• 1997

Analysis of additives in cured rubber is often a difficult task for analytical chemists because of a wide variety of complex components. Conventional analyses of additives and rubbers have been done in multistep, off-line processes with large sample size and extensive sample preparations. The coumarone-indene resin, resorcinol-formaldehyde resin, and prevulcanization inhibitor have been characterized by their pyrolysis pathways and mass spectra of characteristic pyrolyzates. Pyrolysis Gas Chromatography/Mass Spectrometry (Py-GC/MS) was used in the identification of additives without any sample pretreatment. This result shows that several organic additives in cured rubber can be directly analyzed.

• Elastomers and Composites
• /
• v.18 no.2
• /
• pp.51-59
• /
• 1983

The dielectric properties of polymers are very important when investigating the molecular structure of polymers. The characteristics of the dielectric absorption in vulcanized natural rubber were studied in frequency ranging from 10[KHz] to 32[MHz] at the temperature of 25[$^{\circ}C$]. As a result of the study, it has been confirmed that natural rubber vulcanized below 4phr leads to two kinds of dielectric losses due to the interfacial polarization and the dipole polarization by sulfur, and of above 7[%] was only a loss due to the dipole polarization by sulfur. Futhermore, the dielectric loss maximum $tan{\delta}$ spectrum, removed to the low frequency in accordance with increasing sulfur, depends greatly on sulfur. The volume resistivity of $10^{7}{\sim}10^{11}[{\Omega}{\cdot}cm}]$, regardless of whether the crosslinking of rubber is weakened by sulfur, was observed.