• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.20-31
• /
• 2007

Material characteristics and lifetime evaluation are very important in design procedure to assure the safety and reliability of the rubber components. In this paper, the NBR compound was prepared by sulfur-cure system, and was used in predicting the lifetime of rubber gasket made by the compound. The accelerated material aging was investigated at different temperatures at 120, 140 and $160^{\circ}C$ and aging time from 3 hours to 600 hours at 5, 6, 7 vol %. of $H_2SO_4$ concentrations The rubber strips were placed in acid solution using pyrex g1ass tube. Both ends of pyrex g1ass tube were sealed to avoid evaporation of solution during heating at given time. The material test and accelerated acid-heat aging test were carried out to predict the useful life of NBR rubber gasket for a fuel cell stack. In order to investigate the effects of acid-heat aging on the properties of the NBR, tensile strength, elongation at break, hardness and crosslink-density were measured. The tensile strength decreases as the $H_2SO_4$ concentrations and temperature increase. Results were evaluated using Arrhenius equation.

• Elastomers and Composites
• /
• v.19 no.1
• /
• pp.13-31
• /
• 1984

The purposes of this dissertation are to demonstrate that DSC theromoanaytical methods of vulcanization can provide useful informations on the vulcanization characteristics of industrial formulations and also provides the potential basis for a rapid and complete method of sulfur and vulcanizing accelerator analysis for quality control. The influences of those factors such as heating rate, scan temperature, vucanizing accelerator's type and concentration upon vulcanization exotherm in NR and NBR compounds in the presence of vulcanizing accelerators such as TMTD,MBTS,DPG,TMTM,CBS, and MBT were evaluated by means of DSC. In order to examine the credibility in the DSC method, the same samples which were used for DSC method were studied to compare the DSC results with the ODR (Oscillating Disk Rheometer) data. The results obtained were as follows 1. In the DSC dynamic experiments, the observed enthalpy results from vulcanization depends upon the heating rate; In the range of 2 to $20^{\circ}C/min$ of heating rate, as the heating rate was increased the enthalpy change was also increased. However, over the heating rate of $30^{\circ}C/min$ it was observed that the enthalpy change was decreased as the heating rate was further increased. Without regard to the change of enthalpy, tremendous instantaneous heat evolving was observed in the range of high heating rates. 2. For the samples which are added with various vulcanizing accelerators, the activation energies of vulcanization were as follows; 3. Regarding to the influences of vulcanizining accelerator's types upon the characteristics of vulcanization exotherm, NR and NBR compounds in the presence of thiuramsulphide compounds type accelerators such as TMTD, TMTM, were exhibited sharper and higher vulclanization exotherm than others. From the resuts of DSC thermograms which was distributed in even shape in the broad temperature range, it was clearly shown that the guanidine compounds type accelerator such as DPG acts as a delayed acting accelerator. 4. In the comparison of DSC and ODR results, the dependency of temperature in the cure rate and the observed conversions show good agreements between two results. 5. In the same curatives, by the comparison of glass transition temperatures, it was possible to predict relative values of maximum torques. Consequently, from the present studies, it is shown that the DSC thermoanalytical method can provide an alternate new method for rapid and complete quality control analysis of rubber industry.

• Elastomers and Composites
• /
• v.38 no.1
• /
• pp.81-87
• /
• 2003

In this work, $Fe_3O_4$ (magnetite), conductive filler was prepared from $FeCl_2{\cdot}4H_2O,\;(CH_2)_6N_4$ (hexamethylene tetramine), and $NaNO_2$, followed by mixing with crystallizable chloroprene rubber(CR). The influence of conductive filler content on the properties of the conductive composite was studied and temperature dependence of the electrical conductivity (${\sigma}$) was also investigated. It is found that the percolation threshold concept holds true for the conductive particle-filled composite where ${\sigma}$ indicates a nearly sharp increase when the fraction of magnetite in the mixture exceeds 27%. The temperature dependence of ${\sigma}$ is thermally activated blelow or at the $P_c$. Magnetite acts as reinforcement and conductive filler for CR rubber. Moreover, it is shown that the composite with magnetite of 50 phr gives the most significant mechanical properties for tensile strength and elongation at break, which is due to the formation of optimum physical interlock and crosslinking. The results of 100%, 200%, and 300% moduli suggest that the moduli are related with reinforcement effect of magnetite and viscosity of the blend.

• Korean Journal of Plant Resources
• /
• v.10 no.2
• /
• pp.175-182
• /
• 1997

This study was carried out to investigate the effect of several organic fertilizers on the growth characteristics, root yield and the levels of the efficacious constitutents saikosaponins in Bupleurum falcatum L. in the field of Chonnam RDA. Naju, 1994. Five organic fertilizers were used ; rice straw manure(RSM), rice straw(byproduct of mushroom)manure[RS(BM)M], pig-dropping sawdust manure(PSM),poultry manure(PM)and sawdust(byproduct of mushroom) manure[S(BM)M]. The results were summarized as follows ; The chemical properties, such as organic matter, available phosphate, $K_2O$, CaO, and MgO of soil were increased on all plots with the addition of organic fertilizers, specifically in PM+RS(BM)M application. PM+RS(BM)M treatment was higher in emergence rate and better in the growth charaters of shoot, root parts of plants than those of conventional fertilization and the highest dried root yield resulted from using 39% PM+RS(BM)M treatment. Thus, the organic constituents of the plant leaves were affected in the same ways by all treatments, but the T-N, $P_2O_5$, $K_2O$, CaO and MgO contents of the roots were highly increased in PM+RS(BM)M treatment, also the total saikosaponin levels in the roots increased with different organic fertilizers in the following order : 1.70% in PM+RS(BM) treatment, 1.66% in RS(BM) treatment, and 1.57% in RSM+N-P-K treatment. There were significant positive correlation observed between the growth characters of shoot, root parts of plants, yield and contents of T-N, $P_2O_5$, $K_2O$, total-saikosaponin in B. falcatum roots.