• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.57-67
• /
• 1989

Acoustic intensity method is applied to a 4-cylinder gasoline engine in order to identify the noise sources and the response characteristics. Acoustic intensity is analyzed by 1/3 octave band filter for each center frequency. Radiational characteristics of acoustic intensity at overall and the maximum intensity level are represented by using the contour and three-dimensional plot. It is verified that this method is effective to the assessment of engine noise. It can be found that the maximum intensity is radiated from the front side of the engine under idling condition and the right side of it under 2, 000 rpm running with no loading condition at overall level, and also that the maximum intensity is radiated from the oil pan and the intake and exhaust manifold at the center frequency of 100 Hz.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.32-38
• /
• 2004

This study was performed to investigate the behavior of liquid and vapor phase of fuel mixtures with different piston cavity diameters in a optically accessible engine. The conventional engine was modified as Central Injected DI gasoline engine with swirl motion. Two dimensional spray fluorescence images of liquid and vapor phase were acquired to analyze spray behavior and fuel distribution inside of cylinder using exciplex fluorescence method. Piston cavity geometries were set by Type S, M and L. The results obtained are as follows. In the spray formation after SOI, the cone angle and width of the spray were decreased at late injection timing. With a fuel injection timing of BTDC $180^{\circ}C$, fuel was not greatly affected in a piston cavity but generally distributed as homogeneous mixture in the cylinder. With a fuel injection timings of BTDC $90{\circ}C$ and $60^{\circ}C$, fuel mixture was widely distributed in near the cavity center. As a injection timing was late in the compression stroke, residual width of fuel mixture was narrow in proportion to piston cavity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.54-66
• /
• 2000

A gasoline direct injection single cylinder engine has been developed to study operational characteristics for highly stratified conditions. Parameters related to design and experiment were also studied to understand the characteristics of combustion and emissions at some part load conditions. It was found that optimal timings between the end of fuel injection and spark ignition were existed for stable combustion under the stratified modes, In a low engine speed, fuel spray behavior around piston bowl was important for stable combustion. The in-cylinder air motion affecting fuel spray behavior was found to be a dominant factor at higher engine speed as fuel injection timing had to be advanced to secure enough time for fuel evaporation and mixing with surrounding air. As swirl ratio increased, spark timing could be advanced for stable combustion and a higher compression ratio could be used for improved fuel consumption and stable combustion at the stratified mode. It was also observed that electrode geometry and piston bowl shape played an important role for combustion and emission characteristics and some results were shown for comparison.

• Journal of the korean Society of Automotive Engineers
• /
• v.25 no.6
• /
• pp.25-29
• /
• 2003

• Journal of the korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.44-53
• /
• 1995

• Journal of the korean Society of Automotive Engineers
• /
• v.25 no.5
• /
• pp.15-23
• /
• 2003

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1203-1205
• /
• 1987

가솔린 엔진용 전자 제어 에뮬레이션 시스템은 엔진의 운전 상태를 알려 주는 각종 센서로 감지한 정보를 A/D변환기를 통해 마이크로프로세서에 입력시키고, 이 정보를 이용하여 운전 상태를 분석한 후 엔진이 푤요로 하는 연료량, 점화시기, 배기가스의 재순환량, 공회전수 등을 전자적으로 제어하여 엔진의 최적제어를 실현시킴으로서 연료소비율 및 배기가스 중 공해물질 함량을 감소시키기 위한 장치이다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.155-165
• /
• 2013

The effect of gaseous ammonia direct injection on the engine performance and exhaust emissions in gasoline-ammonia dual fueled spark-ignition engine was investigated in this study. Results show that based on the gasoline contribution engine power increases as the ammonia injection timing and duration is advanced and increased, respectively. However, as the initial amount of gasoline is increased the maximum power output contribution from ammonia is reduced. For gasoline-ammonia, the appropriate injection timing is found to range from 320 BTDC at low loads to 370 BTDC at high loads and the peak pressures are slightly lower than that for gasoline due to the slow flame speed of ammonia, resulting in the reduction of combustion efficiency. The brake specific energy consumption (BSEC) for gasoline-ammonia has little difference compared to the BSEC for gasoline only. Ammonia direct injection causes slight reduction of $CO_2$ and CO for all presented loads but significantly increases HC due to the low combustion efficiency of ammonia. Also, ammonia direct injection results in both increased ammonia and NOx in the exhaust due to formation of fuel NOx and ammonia slip.

• Journal of Environmental Health Sciences
• /
• v.24 no.3
• /
• pp.92-98
• /
• 1998

작업장에서 근로자들이 엔진오일 등 각종 오일에 피부가 폭로되었을 때 이것을 쉽게 세척하기 위하여 일반적으로 솔벤트를 사용한다. 그러나 솔벤트를 사용하면 피부를 건조하게 만들 뿐만 아니라 오일에 함유되어 있는 각종 성분들을 피부내에 흡수되는 것을 촉진시킬 수 있어서 이에대한 대처방법이 요구된다. 특히 폐가솔닐엔진오일데는 방향족탄화수소(PAHs)와 같은 물질이 함유되어 있어 체내에 흡수되면 발암물질로 대사되어 표적장기(피부와 폐조직)에서 DNA adducts를 높은 수준으로 형성한다고 알려져 있다. 본 연구에서는 식물기름에서 구할 수 있는 d-라이모닌(Limonene)를 세척제로 사용하여 폐가솔린엔진오일의 폭로로 인하여 형성되는 DNA adducts를 $^{32}P-postlabeling방법으로 분석함으로써 d-라이모닌의 세척효과를 평가하고자 하였다. HDC(ICR) Br 자성마우스의 견갑골 부위에 있는 털을 제거하고 그 부위에 폐가솔린엔진오일을 폭로시키고 1시간과 8시간이 지난 다음에 d-라이모닌으로 각각 세척을 하였다. 마지막 폭로를 마치고 24시간이 지난 다음에 실험동물을 희생시켜 표적장기(폭로된 피부와 폐)에서 시료를 채취하였다. 먼저 시료에서 DNA를 분리하여 가수분해한 다음에 $^{32}P-postlabeling하여 DNA adducts를 분리하였다. 폐가솔린엔진오일만 폭로시킨 그룹의 피부와 폐조직에 형성된 DNA adducts가 각각 30.3$\pm$3.7과 15.7$\pm$2.4로서 대조군(2.5$\pm$1.0과 1.4$\pm$0.4)에 비하여 통계적으로 유의하게 높았고 (p<0.01), 또한 폐조직에서 보다 피부조직에서 통계적으로 유의하게 높았다(p<0.01). 폐가솔린엔진오일을 폭로시킨 후에 d-라이모닌으로 세척한 그룹에서는 피부와 폐조직에 형성된 DNA adducts가 통계적으로 유의하게 감소하였는데(p<0.01), 8시간 보다는 1시간이 지난 다음에 세척한 그룹에서 DNA adducts의 감소현상이 더 크게 나타났다. 결론적으로 피부에 폭로된 폐가솔린 엔진오일을 d-라이모닌으로 세척하면 폐가솔닐엔진오일내에 함유된 발암물질이 체내흡수되는 것이 억제되고, 피부와 폐조직 모두에서 DNA adducts의 형성을 감소시킬 수 있으며, 폐오일이 폭로된 후 빨리 세척하는 것이 더 효과적임을 증명하였다.