• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.59 no.4
• /
• pp.435-444
• /
• 2014

This study was carried out to isolate and characterize the flavonoids present in corn silks. Maysin content in the unpollinated corn silks (Kwangpyeongok) showed its highest level at 3 days after silking, and decreased thereafter, while the content of open pollinated silks were consistently decreased after silking. This result indicates that the maysin content is considerably affected by the pollination of corn silk. Unpollinated corn silks were collected with excising, and ethanol employed to extract flavonoids at common temperature for 9 days. After extraction, chlorophyll, lipids etc. were removed with methylene chloride, then submitted to flash column cartridge ($150{\times}40mm$ i.d.) packed with a preparative $RP-C_{18}$ bulk packing material ($125{\AA}$, $55-105{\mu}m$), and monitored at 352 nm. Four fractions, fraction-I, -II, -III, and -IV, were isolated from ethanolic extract of corn silks. Absorption spectrum of fraction I showed its maximum intensity (${\lambda}_{max}$) at 327 nm and 239 nm, fraction-II showed its maximum intensity at 339 nm and 274 nm, fraction-III showed its maximum intensity at 345 nm and 277 nm, and fraction-IV showed its maximum intensity at 352 nm, 270 nm, 257 nm, respectively. On the baisis of ESI micro-TOF analysis, fraction-I was identified as chlorogenic acid (m/z 355, 3-(3,4-dihydroxycinnamoyl) quinic acid, $C_{16}H_{18}O_9$), fraction-II identified as a mixture of chlorogenic acid and luteolin 3'-methyl ether 7-glucuronosyl-($1{\rightarrow}2$)-glucuronide (m/z 653, $C_{28}H_{28}O_{18}$), fraction-III identified as a mixture of chlorogenic acid luteolin 7-O-neohesperidoside (m/z 595, $C_{27}H_{30}O_{15}$), and luteolin 3'-methyl ether 7-glucuronosyl-($1{\rightarrow}2$)-glucuronide, and fraction-IV identified as maysin (m/z 577, 2"-O-${\alpha}$-L-rhamnosyl-6-C-(6-deoxy-xylohexose-4-ulosyl)luteolin, $C_{27}H_{28}O_{14}$), respectively. From the ethanolic extract of corn silks, fraction-I was obtained about 35 mg/100 g F.W., fraction-II was about 48 mg/100 g F.W., fraction-III was about 46 mg/100 g F.W., and fraction-IV was about 138 mg/100 g F.W., respectively.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.73-77
• /
• 2001

We studied the fabrication of GaAs-based pseudomorphic high electron mobility transistors(PHEMT`s) for the purpose of millimeter- wave applications. To fabricate the high performance GaAs-based PHEMT`s, we performed the simulation to analyze the designed epitaxial-structures. Each unit processes, such as 0.1 m$\mu$$\Gamma$-gate lithography, silicon nitride passivation and air-bridge process were developed to achieve high performance device characteristics. The DC characteristics of the PHEMT`s were measured at a 70 $\mu$m unit gate width of 2 gate fingers, and showed a good pinch-off property ($V_p$= -1.75 V) and a drain-source saturation current density ($I_{dss}$) of 450 mA/mm. Maximum extrinsic transconductance $(g_m)$ was 363.6 mS/mm at $V_{gs}$ = -0.7 V, $V_{ds}$ = 1.5 V, and $I_{ds}$ =0.5 $I_{dss}$. The RF measurements were performed in the frequency range of 1.0~50 GHz. For this measurement, the drain and gate voltage were 1.5 V and -0.7 V, respectively. At 50 GHz, 9.2 dB of maximum stable gain (MSG) and 3.2 dB of $S_{21}$ gain were obtained, respectively. A current gain cut-off frequency $(f_T)$ of 106 GHz and a maximum frequency of oscillation $(f_{max})$ of 160 GHz were achieved from the fabricated PHEMT\\`s of 0.1 m$\mu$ gate length.h.

• Structural Engineering and Mechanics
• /
• v.62 no.1
• /
• pp.21-31
• /
• 2017

Engineered Cementitious Composite (ECC) is a special class of the new generation of high performance fiber reinforced cementitious composites (HPFRCC) featuring high ductility with relatively low fiber content. In this research, the mechanical performance of ECC beams will be investigated with respect to the effect of slag and aggregate size and amount, by employing nonlinear finite element method. The validity of the models was verified with the experimental results of the ECC beams under monotonic loading. Based on the numerical analysis method, nonlinear parametric study was then conducted to evaluate the influence of the ECC aggregate content (AC), ECC compressive strength ($f_{ECC}$), maximum aggregate size ($D_{max}$) and slag amount (${\phi}$) parameters on the flexural stress, deflection, load and strain of ECC beams. The simulation results indicated that when increase the slag and aggregate size and content no definite trend in flexural strength is observed and the ductility of ECC is negatively influenced by the increase of slag and aggregate size and content. Also, the ECC beams revealed enhancement in terms of flexural stress, strain, and midspan deflection when compared with the reference beam (microsilica MSC), where, the average improvement percentage of the specimens were 61.55%, 725%, and 879%, respectively. These results are quite similar to that of the experimental results, which provides that the finite element model is in accordance with the desirable flexural behaviour of the ECC beams. Furthermore, the proposed models can be used to predict the flexural behaviour of ECC beams with great accuracy.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.57-63
• /
• 2002

In order to increase the magnetic properties of a Nd-Fe-B sintered magnet, the general factors including particle size and its distribution, volume fraction of Nd$_2$Fe$_{14}$B phase, degree of alignment of Nd$_2$Fe$_{14}$B grain, oxygen content and grain size etc. should be optimized by controlling the composition of Nd-Fe-B alloy as well as the manufacturing process. In this study, fabrication of the Nd-Fe-B sintered magnet was carried out in a laboratory scale by controlling the composition of Nd-Fe-B alloy and the manufacturing process. The optimum milling condition was found by investigating the milling media, milling time and ball size. The addition of FeGa was effective to increase the coercivity of the Nd-Fe-B sintered magnet. A remanence of 14.4 kG, a coercivity of 9.4 kOe and a maximum energy product of 47 MGOe were obtained from the sintered magnet.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.3041-3046
• /
• 2014

Blue emitting materials, 9,10-bis-biphenyl-4-yl-anthracene (AC-P), 9,10-bis-[1,1';4',1"]terphenyl-4-yl-anthracene (AC-DP), and 9,10-bis[3",5"-deiphenyltriphenyl-4'-yl]anthracene (AC-TP) were synthesized through boration and Suzuki aryl-aryl coupling reaction. EL performance of blue light-emitters was optimized and improved by varying the chemical structures of the side groups. In the thin film state, the three materials exhibit $PL_{max}$ values in the range of 442-456 nm. EL device with the synthesized compounds in the following configuration was fabricated: ITO/4,4',4"-tris(N-(2-naphthyl)-N-phenylamino)triphenylamine (2-TNATA) 60nm/N,N'-bis (naphthalene-1-yl)-N,N'-bis(phenyl)benzidine (NPB) 15nm/synthesized blue emitting materials (30nm)/1,3,5-tri(1-phenyl-1H-benzo[d]imidazol-2-yl)phenyl (TPBi) 20nm/LiF 1nm/Al 200nm. The current efficiency and C.I.E. value of AC-TP were 3.87 cd/A and (0.15, 0.12). A bulky and non-planar side group helps to prevent ${\pi}-{\pi}^*$ stacking interaction, which should lead to the formation of more reliable amorphous film. This is expected to have a positive effect on the high efficiency of the operating OLED device.

• Nuclear Medicine and Molecular Imaging
• /
• v.41 no.5
• /
• pp.359-363
• /
• 2007

Purpose: Incidental parotid lesions on F-18 FDG-PET can mimic distant metastasis of underlying malignancy. The prevalence and the clinico-pathologic findings of PET positive parotid lesions have not been known. We investigated how often incidental parotid lesions are found on clinical FDG-PET studies and what the clinico-pathologic characteristics of those parotid lesions are in the present study. Materials and Methods: We retrospectively reviewed 3,344 cases of FDG-PET which had been obtained in our hospital from May 2003 to Dec 2006. The indications of FDG-PET were: evaluation of known/suspected cancer (n= 3,212) or screening of cancer in healthy subjects (n=132). Incidental parotid lesion on FDG-PET was defined as an un-expected FDG uptake in one of parotid glands which was not primary target lesion of current FDG-PET. FDG uptake was represented by maximum standardized uptake value (maxSUV). Final diagnosis was made by pathologic analysis or clinical follow-up assessment. Results: Fifteen (0.45% = 15/3,344) incidental parotid lesions were found and they were all benign lesions. The maxSUV ranged from 1.7 to 8.6 (mean${\pm}$s.d. = $3.7{\pm}1.9$). Final diagnoses of the incidental parotid lesions were; Warthin's tumor (n=2), pleomorphic adenoma (n=1), other un-specified benign lesion (n=1), and benign lesions under bases of imaging studies (n=3) and of clinical follow-up (n=8). Conclusion: All of incidentally found parotid lesions in clinical FDG-PET studies were confirmed as benign lesions with prevalence of 0.45%. Close follow up using PET or CT might be a reasonable approach for determining the nature of incidentally found parotid lesions.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.975-976
• /
• 1993

This talk presents the overview of the author's research and development activities on fuzzy inference hardware. We involved it with two distinct approaches. The first approach is to use application specific integrated circuits (ASIC) technology. The fuzzy inference method is directly implemented in silicon. The second approach, which is in its preliminary stage, is to use more conventional microprocessor architecture. Here, we use a quantitative technique used by designer of reduced instruction set computer (RISC) to modify an architecture of a microprocessor. In the ASIC approach, we implemented the most widely used fuzzy inference mechanism directly on silicon. The mechanism is beaded on a max-min compositional rule of inference, and Mandami's method of fuzzy implication. The two VLSI fuzzy inference chips are designed, fabricated, and fully tested. Both used a full-custom CMOS technology. The second and more claborate chip was designed at the University of North Carolina(U C) in cooperation with MCNC. Both VLSI chips had muliple datapaths for rule digital fuzzy inference chips had multiple datapaths for rule evaluation, and they executed multiple fuzzy if-then rules in parallel. The AT & T chip is the first digital fuzzy inference chip in the world. It ran with a 20 MHz clock cycle and achieved an approximately 80.000 Fuzzy Logical inferences Per Second (FLIPS). It stored and executed 16 fuzzy if-then rules. Since it was designed as a proof of concept prototype chip, it had minimal amount of peripheral logic for system integration. UNC/MCNC chip consists of 688,131 transistors of which 476,160 are used for RAM memory. It ran with a 10 MHz clock cycle. The chip has a 3-staged pipeline and initiates a computation of new inference every 64 cycle. This chip achieved an approximately 160,000 FLIPS. The new architecture have the following important improvements from the AT & T chip: Programmable rule set memory (RAM). On-chip fuzzification operation by a table lookup method. On-chip defuzzification operation by a centroid method. Reconfigurable architecture for processing two rule formats. RAM/datapath redundancy for higher yield It can store and execute 51 if-then rule of the following format: IF A and B and C and D Then Do E, and Then Do F. With this format, the chip takes four inputs and produces two outputs. By software reconfiguration, it can store and execute 102 if-then rules of the following simpler format using the same datapath: IF A and B Then Do E. With this format the chip takes two inputs and produces one outputs. We have built two VME-bus board systems based on this chip for Oak Ridge National Laboratory (ORNL). The board is now installed in a robot at ORNL. Researchers uses this board for experiment in autonomous robot navigation. The Fuzzy Logic system board places the Fuzzy chip into a VMEbus environment. High level C language functions hide the operational details of the board from the applications programme . The programmer treats rule memories and fuzzification function memories as local structures passed as parameters to the C functions. ASIC fuzzy inference hardware is extremely fast, but they are limited in generality. Many aspects of the design are limited or fixed. We have proposed to designing a are limited or fixed. We have proposed to designing a fuzzy information processor as an application specific processor using a quantitative approach. The quantitative approach was developed by RISC designers. In effect, we are interested in evaluating the effectiveness of a specialized RISC processor for fuzzy information processing. As the first step, we measured the possible speed-up of a fuzzy inference program based on if-then rules by an introduction of specialized instructions, i.e., min and max instructions. The minimum and maximum operations are heavily used in fuzzy logic applications as fuzzy intersection and union. We performed measurements using a MIPS R3000 as a base micropro essor. The initial result is encouraging. We can achieve as high as a 2.5 increase in inference speed if the R3000 had min and max instructions. Also, they are useful for speeding up other fuzzy operations such as bounded product and bounded sum. The embedded processor's main task is to control some device or process. It usually runs a single or a embedded processer to create an embedded processor for fuzzy control is very effective. Table I shows the measured speed of the inference by a MIPS R3000 microprocessor, a fictitious MIPS R3000 microprocessor with min and max instructions, and a UNC/MCNC ASIC fuzzy inference chip. The software that used on microprocessors is a simulator of the ASIC chip. The first row is the computation time in seconds of 6000 inferences using 51 rules where each fuzzy set is represented by an array of 64 elements. The second row is the time required to perform a single inference. The last row is the fuzzy logical inferences per second (FLIPS) measured for ach device. There is a large gap in run time between the ASIC and software approaches even if we resort to a specialized fuzzy microprocessor. As for design time and cost, these two approaches represent two extremes. An ASIC approach is extremely expensive. It is, therefore, an important research topic to design a specialized computing architecture for fuzzy applications that falls between these two extremes both in run time and design time/cost. TABLEI INFERENCE TIME BY 51 RULES {{{{Time }}{{MIPS R3000 }}{{ASIC }}{{Regular }}{{With min/mix }}{{6000 inference 1 inference FLIPS }}{{125s 20.8ms 48 }}{{49s 8.2ms 122 }}{{0.0038s 6.4㎲ 156,250 }} }}

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.65-69
• /
• 2011

Purpose: Normal pancreas has low uptake rate in $^{18}F$-FDG PET scan. However, it is possible to diagnose malignancy of pancreatic cancer which has high uptake rate. Many studies approve a high prevalence of diabetes in pancreatic cancer and if the blood glucose level (BGL) is over the normal range, FDG uptake will be decreased and there will be inconvenience for patients from the delay time to reduce the high BGL or could cause difficulty to arrange the schedule. Therefore, we studied the relation of BGL and image quality in pancreatic cancer on PET. Materials and Methods: A hundred patients had PET scan. The prevalence of pancreatic cancer and diabetes were evaluated using SPSS ver. 17. The fasting BGL of patients were examined and sorted as diabetes mellitus (DM) group and Non-DM group. For the evaluation, patients were divided into 3 groups (Non-DM, DM; BGL${\geq}7.0mmol/L$, and DM; BGL<7.0 mmol/L). The ROI was drown on Liver and Lung for the PET imaging analysis. Results: Fifty three male and forty seven female were in the patients. The average age was $60.1{\pm}13.5$. There were 36 patients (male: 22, female: 14, 36%) who had pancreatic cancer with DM. There were 15 patients who showed over 7.0 mmol/L in their fasting BGL and 85 patients who showed under 7.0 mmol/L in their fasting BGL. Among the Non-DM, DM; BGL${\geq}7.0mmol/L$, and DM; BGL<7.0 mmol/L, there was not a statistical significance (p>0.05). Conclusion: The prevalence of pancreatic cancer was comparatively high in this study. If the fasting BGL was slightly over the normal BGL, we believe it will not give a severe disturbance when the patients have PET scan. Furthermore, the examination schedule doesn't need to change and the inconvenience from the delay of patients preparation will be reduced.

• Journal of Microbiology and Biotechnology
• /
• v.17 no.1
• /
• pp.58-66
• /
• 2007

Isolation, expression, and characterization of a novel $endo-{\beta}-1,3(4)-D-glucanase$ with high specific activity and homology to Bacillus lichenases is described. One clone was screened from a genomic library of Paenibacillus sp. F-40, using lichenan-containing plates. The nucleotide sequence of the clone contains an ORF consisting of 717 nucleotides, encoding a ${\beta}-glucanase$ protein of 238 amino acids and 26 residues of a putative signal peptide at its N-terminus. The amino acid sequence showed the highest similarity of 87% to other ${\beta}-1,3-1,4-glucanases$ of Bacillus. The gene fragment Bg1 containing the mature glucanase protein was expressed in Pichia pastoris at high expression level in a 3-1 high-cell-density fermenter. The purified recombinant enzyme Bg1 showed activity against barley ${\beta}-glucan$, lichenan, and laminarin. The gene encodes an $endo-{\beta}-1,3(4)-D-glucanase$ (E. C. 3.2.1.6). When lichenan was used as substrate, the optimal pH was 6.5, and the optimal temperature was $60^{\circ}C$. The $K_m,\;V_{max},\;and\;k_{cat}$ values for lichenan are 2.96mg/ml, $6,951{\mu}mol/min{\cdot}mg,\;and\;3,131s^{-1}$, respectively. For barley ${\beta}-glucan$ the values are 3.73mg/ml, $8,939{\mu}mol/min{\cdot}mg,\;and\;4,026s^{-1}$, respectively. The recombinant Bg1 had resistance to pepsin and trypsin. Other features of recombinant Bg1 including temperature and pH stability, and sensitivity to some metal ions and chemical reagents were also characterized.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.214-219
• /
• 1997

The mechanical seals, which are installed in rotating machines like pump and compressor, are generally used as sealing devices in the many fields of industries. The failure of mechanical seals such as leakage, crack, breakage, fast and severe wear, excessive torque, and squeaking results in big problems. To identify abnormal phenomena on mechanical seals and to propose the proper monitoring parameter for the failure of mechanical seals, sliding wear experiments were conducted. Acoustic emission, torque, and temperature were measured during experiments. Optical microstructure was observed for the wear processing after every 10 minute sliding at rotation speed of 1750 rpm and scanning electron microscopy was also observed. Except for the initial part of every experiment, the variation of acoustic emission was well coincided with torque variation during the experiments. This study concludes that acoustic emission and torque are proper monitoring parameters for the failure of mechanical seals. The intensity of acoustic emission signals is measured in root mean square voltage. Temperature of sealing face will be used as a parallel parameter for increasing the reliability of monitoring system.