• Journal of the Korean Society of Combustion
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2007

Analytical investigation of acoustic wave scattering from turbulent premixed flames was conducted to evaluate the acoustic energy amplification/damping. Such acoustic energy change is attributed to the acoustic velocity jump due to flame's heat release. Small perturbation method up to second order and stochastic analysis were utilized to formulate net acoustic energy and the energy transfer from coherent to incoherent energy. Randomly wrinkled flame surface is responsible for the energy transfer from coherent to incoherent field. Nondimensional parameters that govern net acoustic energy were determined: rms height and correlation length of flame front, incident wave frequency, incidence angle, and temperature ratio. The dependence of net acoustic energy upon these parameters is illustrated by numerical simulations in case of Gaussian statistics of flame front. Total net energy was amplified and the major factors that affect such energy amplification are incidence angle and temperature ratio. Coherent (incoherent) energy is damped (amplified) with rms height and correlation length of flame front.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.171-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to indentify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method was applied to a passenger car. It can be seen that complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.46.1-46.1
• /
• 2011

New statistical method is proposed to coherently combine Baryon Acoustic Oscillation statistics (BAO) and peculiar velocity measurements exploiting decomposed density--density and velocity--velocity spectra in real space from the observed redshift distortions in redshift space, 1) to achieve stronger dark energy constraints, sigma(w)=0.06 and sigma(w_a)=0.20, which are enhanced from BAO or velocity measurements alone, and 2) to cross--check consistency of dark energy constraints from two different approaches; BAO as geometrical measurements and peculiar velocity as large scale structure formation observables.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.159-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to inden- tify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.319-323
• /
• 2003

In this paper, we propose a hybrid transceiver for underwater acoustic communication, which allows the system to reduce complexity and increase robustness in time variant underwater channel environments. It is designed in the digital domain except for amplifiers and implemented by using a multiple digital signal processors (DSPs) system. The digital modulation technique is quadrature phase shift keying (QPSK) and frame synchronization is an energy (non-coherent) detection scheme based on the quadrature receiver structure. DSP implementation is based on block data parallel architecture (BDPA). We shaw experimental results in th? underwater anechoic basin at KRISO. The results indicate that the frame synchronization is performed without PLL. Also, we shaw that the adaptive equalizer can compensate frame synchronization error and the correction capability is dependent on the length of equalizer.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.143-150
• /
• 2005

To verify applicability of multi-dimensional spectral analysis (MDSA) fur noise source identification two different approaches which are frequency response and coherent function have been investigated. The coherence function approach appears able to separate the correlated system when the noise sources were coherent. In this study, we identify contribution of structure-borne-noise of vehicle HVAC system using MDSA method. Firstly, to identify the applicability of MDSA method, 4-inputs of vehicle HVAC system were the signals measured by accelerometers attached on the selected noise sources which were composed of blower, evaporator, heater and duct. While 1-output which was driver's position sound was the SPL signals measured by a remote microphone, when the blower motor was operating. We identify efficiency of systems modeled with four Inputs/single output through ordinary coherence function (OCF) and partial coherence function (PCF). As a result of experiment, the blower accounted for $62-88\%$ of the overall level of sound energy density. Also, according to the analysis of acoustic signal and vibration signals measurement, an investigation of the noise source identification in the vehicle HVAC is presented. With the sound intensity method, the major sources of the vehicle HVAC radiation are verified. Also the method of improving the noise reduction is proposed by attaching damping patch access to blower motor and noise reduction is verified.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.8
• /
• pp.708-718
• /
• 2002

In this paper, the problems in identifying the noise sources by using the sound intensity technique are dealt with for the general radiated near-field from vibro-acoustic sources. For this purpose, a three-dimensional model structure resembling the engine room of a car or heavy equipment is considered. Similar to the practical situations, the model contains many mutually coherent and incoherent noise sources distributed on the complicated surfaces. The sources are located on the narrow, connected, reflecting planes constructed with rigid boxes, of which a small clearance exists between the whole box structure and the reflecting bottom. The acoustic boundary element method is employed to calculate the acoustic intensity at the near-field surfaces and interior spaces. The effects of relative source phases, frequencies, and locations are investigated, from which the results are illustrated by the contour map, vector plot, and energy streamlines. It is clearly observed that the application of sound intensity technique to the reactive or reverberant field, e.g., scanning over the upper engine room as is usually practiced, can yield the detection of fake sources. For the precise result for such a field, the field reactivity should be checked a priori and the proper effort should be directed to reduce or improve the reactivity of sound field.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.6
• /
• pp.545-555
• /
• 2020

This paper presented efficient transceiver structure using sub-band processing for underwater communication in terms of covertness and performance improvement. In aspect of covertness, encrypted coded-bits are divided into groups, and center frequency and sub band are determined by coded-bits of each group. Therefore, as center frequencies are changed randomly, it maintain the covertness effectively. In aspect of performance improvement, the performance of underwater communication mainly depends on multi-path propagation characteristics, Doppler-spread, and frame synchronization. Accordingly, in order to overcome these effects, non-coherent energy detector and turbo equalization method are employed in receiver side. Furthermore, optimal frame synchronization was proposed. Through the simulation and lake experiment, performance analysis was conducted. Especially in the lake experiment, as a result of applying optimal frame synchronization method to receiver structure, errors are corrected in most frames.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.9
• /
• pp.1248-1256
• /
• 1993

The propagation and delay properties in opical fiber are particularly attractive because digital signal processing and conventional analog signal processing techniques such as those using surface acoustic wave devices are limited In their usefulness for signal bandwidth exceeding one or two GHz, although they are very effective at lower frequencies. Since an accurate, low loss and short time delay elements can be obtained by using such an optical fiber, optical signal precessing has attracted much attention for high speed and broad-band signal precessing in particular channel separation filtering for optical FDM signals. In this paper, we consider a coherent optical lattice filter, which uses coherent light sources and consists of directional couplers and optical fiber delay elemnts. The optical fiber fitters are more restricted than the usual digital filters. The reasons are as follows. 1) the coupling coefficients of directional couplers are restricted to the number between 0 and 1. 2) optical signal E(complex amplitude) is divided into J If-$\boxUl$ and J L/7$\div$$\boxUl$ at the directional coupler. Considering these restrictions and in this case all the coupling coefficients of summing and branching elements are set to be equal, we have given design formulae for optical lattice filter, which make the best use of optical signal energy.