• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.5
• /
• pp.1082-1088
• /
• 2003

This study is about the development of a system related to the CATV network. It intends to develop an automatically centralized Headend system and a distributive system to remove the ineffectiveness of the established manual system. To achieve this goal, we took a put of bandwidth, which is not used for the transmission of video signals in the established frequency bandwidth, and used it for the transmission and receiver of controlling signals. By this way we could design a system of transmission and receiver and a automatic distributive system. We developed an information management system for the 9600bps CATV using RS-232 of forward/backward communication and backward communication. Based on window, It consist of ID generation, transmitter/receiver, control and backup part.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.4
• /
• pp.55-62
• /
• 2002

FRLGC(Fiber Ring laser Gain Clamped) EDFA Is demonstrated for an automatic gain control in hi-directional ADM(Add Drop Multiplexer) node configuration. Specifically, we investigate hi-directional characteristics of noise figure. Assuming a hi-directional small signal input, noise figures for forward or backward signal input are calculated using average inversion algorithm, according to the propagating directions and lasing wavelengths of a compensating signal. The operating condition of FRLGC-EDFA may be optimized with a backward lasing and short lasing wavelength in the aspect of hi-directional noise figure characteristics.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.2
• /
• pp.95-100
• /
• 2002

By feedback channel, the decoder reports the addresses of corrupted macroblocks induced by transmission errors back to the encoder With these negative acknowledgements, the encoder can make the next frame having propagated errors by using forward dependency based on GOBs and MBs of the frame happening transmission errors. The encoder can precisely calculate and track the propagated errors by examining the backward motion dependency for each of four comer pixels in the current encoding frame until before-mentioned the next frame. The error-propagation effects can be terminated completely by INTRA refreshing the affected macroblocks. Such a fast algorithm further reduce the computation and memory requirements. The advantages of the low computation complexity and the low memory requirement are Particularly suitable for real-time implementation.

• International Journal of Highway Engineering
• /
• v.16 no.1
• /
• pp.111-118
• /
• 2014

PURPOSES : This study performs fundamental research on ramp-metering design criteria. METHODS : We carefully review previous studies in terms of ramp-metering design criteria and then consider applicability in Korea. For this, traffic simulation model is employed to analyze actual effect according to specific location of stop-line when implementing ramp-metering. RESULTS : When a stop-line moving forward with a 50m interval, travel speed at mainline relative to current stop-line location tends to decrease. However, traveling speed at approach roads increase about 5~18% under the same condition. When a stop-line location moving backward with a 50m interval, mainline travel speed increase approximately 17~32% whereas traveling speed at approach roads decrease. All cases are compared with the current stop-line location. CONCLUSIONS : We believe that both cases are useful with respect to freeway management. For example, moving forward a stop-line case can be used management for queuing area at ramp section and approach roads. Moving backward a stop-line case can be used for traffic control, focusing on mainline of freeways.

• Journal of Environmental Science International
• /
• v.30 no.6
• /
• pp.475-485
• /
• 2021

This research investigated the characteristics of fine particles during cold front passage in Busan, on March 19, 2020. The cold front speed was 17.4 m/s (about 63k km/hr), moving from the northwest to the southeast, and with a width of about 64 km. The backward trajectory analysis showed that a southern sea air parcel flowed into Busan before the cold front passage, carrying continental materials from China transported into Busan after cold front passage. The PM₁₀ concentration in Busan showed a rapid increase after passing through the cold front, with PM_2.5 showing a high concentration during cold front passage. The PM_2.5/PM₁₀ ratio was 0.10 - 0.30. When the cold front passed, SO₄^2-, NO₃^-, Ca²⁺, NH₄⁺, Na⁺, and K⁺ in PM_2.5 showed a rapid increase, with SO₄^2- showing the most significant increase. These results indicated that understanding the characteristics of fine particles during cold front passage in Busan could provide insight into establishing a strategy to control urban air quality.

• Advances in nano research
• /
• v.10 no.2
• /
• pp.129-138
• /
• 2021

In present article, utilizing the Love shell theory with volume fraction laws for the cylindrical shells vibrations provides a governing equation for the distribution of material composition of material. Isotopic materials are the constituents of these rings. The position of a ring support has been taken along the radial direction. The Rayleigh-Ritz method with three different fraction laws gives birth to the shell frequency equation. Moreover, the effect of height- and length-to-radius ratio and angular speed is investigated. The results are depicted for circumferential wave number, length- and height-radius ratios with three laws. It is found that the backward and forward frequencies of exponential fraction law are sandwich between polynomial and trigonometric laws. It is examined that the backward and forward frequencies increase and decrease on increasing the ratio of height- and length-to-radius ratio. As the position of ring is enhanced for clamped simply supported and simply supported-simply supported boundary conditions, the frequencies go up. At mid-point, all the frequencies are higher and after that the frequencies decreases. The frequencies are same at initial and final stage and rust itself a bell shape. The shell is stabilized by ring supports to increase the stiffness and strength. Comparison is made for non-rotating and rotating cylindrical shell for the efficiency of the model. The results generated by computer software MATLAB.

• Journal of Environmental Science International
• /
• v.31 no.6
• /
• pp.515-524
• /
• 2022

This study investigated characteristics of meteorological parameters and ionic components of PM_2.5 during Asian dust events on November 28 and 30, 2018 at Busan, Korea. The seasonal occurrence frequencies of Asian dust during 1960~2019 (60 years) were 81.7% in spring, 12.2% in winter, and 6.1% in autumn. Recently, autumn Asian dust occurrence in Busan has shown an increasing trend. The result of AWS (automatic weather station), surface weather chart, and backward trajectory analyses showed that the first Asian dust of Nov. 28, 2018, in Busan came with rapid speed through inner China and Bohai Bay from Mongolia. The second Asian dust of Nov. 30, 2018, in Busan seems to have resulted from advection and deposition of proximal residual materials. These results indicated that understanding the characteristics of meteorological parameters and ionic components of PM_2.5 during Asian dust events could provide insights into establishing a control strategy for urban air quality.

• Journal of information and communication convergence engineering
• /
• v.5 no.2
• /
• pp.88-92
• /
• 2007

In this paper, an SS-RRA protocol that is based on Code Division Multiple Access is proposed and analyzed under the integrated voice and data traffic load. The backward logical channels consist of slotted time division frames with multiple spreading codes per slot. The protocol uses a reservation mechanism for the voice traffic, and a random access scheme for the data traffic. A discrete-time, discrete-state Markov chain is used to evaluate the performance. The numerical results show that the performance can be significantly improved by a few distinct spreading codes.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.3
• /
• pp.330-336
• /
• 2009

This paper studies on the new control algorithm for the mass-flow stabilization in strip head part of a hot strip mill. A new strip tension model in the strip head part is derived using the current deviation of two neighboring stands. The current deviation means a difference between a measured current and a lock-on current, where the lock-on current is set up when a strip tension or a looper angle reaches each target value or time is about 0.4sec, respectively. On the basis of the tension calculation model, a mill velocity of a backward stand is controlled to stabilize a strip mass-flow by PI control algorithm. Therefore, the mass-flow control for strip head part is executed from a metal-in time into a foreward stand till the looper works normally. It is known by the results of a computer simulation and an experiment that the proposed control algorithm is very effective in stabilizing the mass flow of the strip head part.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.11
• /
• pp.1130-1136
• /
• 2009

A new control algorithm for the yaw motion control of a unicycle robot has been proposed in this paper. With the increase of life quality, there are various transportation systems such as segway and unicycle robot which provide not only transportation but also amusement. In most of the unicycle robots share the same technology in that the directions of roll and pitch are controlled by the balance controllers, allowing the robots to maintain balance for a long period by continuously moving forward and backward. However, one disadvantage of this technology is that it cannot provide the capability to the robots to avoid obstacles in their path way. This research focuses to provide the yawing function to the unicycle robot and to control the yaw motion to avoid the obstacles as desired. For the control of yawing motion, the yaw angle is adjusted to the inertia generated by the velocity and torque of a yawing motor which is installed in the center axes of the unicycle robot to keep the lateral control simple. Through the real experiments, the effective and robustness of the yawing control algorithm has been demonstrated.