• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.327-333
• /
• 2022

In this study, silicon/carbon nanotube/carbon (Si/CNT/C) composites for anode were prepared to improve the volume expansion of silicon used as a high-capacity anode material. Si/CNT were prepared by electrostatic attraction of the positively charged Si and negatively charged CNT and then hydrothermal synthesis was performed to obtain the spherical Si/CNT/C composites. Poly(vinylidene fluoride) (PVDF), polyacrylic acid (PAA), and styrene butadiene rubber (SBR) were used as binders for electrode preparation, and coin cell was assembled using 1.0 M LiPF₆ (EC:DMC:EMC = 1:1:1 vol%) electrolyte and fluoroethylene carbonate (FEC) additive. The physical properties of Si/CNT/C anode materials were analyzed using SEM, EDS, XRD and TGA, and the electrochemical performances of lithium-ion batteries were investigated by charge-discharge cycle, rate performance, dQ/dV and electrochemical impedance spectroscopy tests. Also, it was confirmed that both capacity and rate performance were significantly improved using the PAA/SBR binder and 10 wt% FEC-added electrolyte. It is found that Si/CNT/C have the reversible capacity of 914 mAh/g, the capacity retention ratio of 83% during 50 cycles and the rate performance of 70% in 2 C/0.1 C.

• Microbiology and Biotechnology Letters
• /
• v.26 no.2
• /
• pp.179-186
• /
• 1998

Dextransucrase hyper-producing Leuconostoc mesenteroides B-512FMCM and dextransucrase constitutive mutants B-742CB and B-1355C catalyzed the transfer of glucose from sucrose to other carbohydrates which were present or were added to the reaction digests. When the acceptor was a maltose, gentiobiose, lactose or raffinose, there was produced a series of oligosaccharide acceptor products or single product based on the kinds of enzymes and reaction conditions. To obtain the quantitative information about the yield and the distribution of acceptor products and dextran two experimental parameters were studied: a) the ratio of acceptor to sucrose and b) the amount of enzyme at constant carbohydrate concentration (100 mM). As the amount of enzyme increased, the synthesis of acceptor products (of maltose or gentiobiose) increased, and the formation of dextran decreased. As the ratio of acceptor to sucrose increased, the amount of dextran and the number of acceptor-products decreased and the amount of acceptor-products increased. When maltose or gentiobiose was an acceptor, the glucose from sucrose was transferred to the C-6 hydroxyl group of the nonreducing-end glucose residue of accepters to give a homologous series of isomaltosyl dextrins. In case of lactose or raffinose, there was produced only one acceptor product from B-512FMCM dextransucrase reaction. In the lactose acceptor reaction, the glucose from sucrose was transferred to the C-2 hydroxyl of the reducing end glucose residue of lactose. To get a series of oligosaccharides from lactose or raffinose acceptor reaction we used B-742CB dextransucrase or B-1355C alternansucrase with 500 mM sucrose in reaction digest.

• Tuberculosis and Respiratory Diseases
• /
• v.48 no.2
• /
• pp.155-165
• /
• 2000

Background: The phagolysosomal function of alveolar macrophage against M. tuberculosis infection is influenced by Nramp1, which is encoded by the NRAMP1 gene. There are several genetic polymorphisms in NRAMP1, and these polymorphisms affect the innate host resistance through the defect in production and function of Nramp1. To investigate this relationship, the NRAMP1 genetic polymorphism in patients with primary tuberculous pleurisy was determined. Methods: Fifty-six primary tuberculous pleurisy patient, who were diagnosed by pleural biopsy, were designated to the pleurisy group and 45 healthy adults were designated to the healthy control group. Three genetic polymorphisms of NRAMP1, such as a single point mutation in intron 4(469+14G/C, INT4), a nonconservative single-base substitution at codon 543 that changes aspartic acid to asparagine(D543N) and a TGTG deletion in the 3' untranslated region(1729+55delI4, 3'UTR), were determined. Polymerase chain reaction(PCR) and polymerase chain reaction-restriction fragment length polymorphism(PCR-RFLP) were used. Results: The frequencies of mutant genotypes of INT4 and 3'UTR were significantly high in pleurisy group(p=0.001, p=0.023). But the frequencies of D543N were not significantly different between the two groups(p=0.079). The odds ratios, which are a comparison with wild genotype for determining mutant genotypes, were 8. 022(95% confidence interval=2.422-26.572) for INT4 and 5.733(95% confidence interval = 1.137~28.916) for 3'UTR ; these were statistically significant But the ratio for D543N was not significant In the combined analysis of the INT4 and 3'UTR polymorphisms, the odds ratios were 6.000(95% confidence interval = 1.461~24.640) for GC/++ genotype and 14.000(95% confidence interval=1.610~121.754) for GC/+del when compared with GG/++ homozygotes ; these were statistically significant. Conclusion: Among the NRAMP1 genetic polymorphisms, a single point mutation in intron 4(469+14G/C, INT4) and a TGTG deletion in the 3' untranslated region(1729+55del4, 3'UTR) were closely related to the primary tuberculous pleurisy.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.5
• /
• pp.290-297
• /
• 2009

In case of using Asymmetric Bipolar Pulsed DC (ABPD) power generator, thin film is efficiently deposited as ions are getting higher energy by suppressing target poisoning and electric arc. In this article, the mechanical properties of CNx thin films deposited on the STS 316L were compared with DC and ABPD power generators. The CNx thin films deposited with ABPD clearly improved wear resistance by higher ratio of sp3CN as compared with DC. Nb interlayer affected to increase the value of 10N of adhesion between CNx thin films and substrate. But, CNx thin films deposited with ABPD couldn't endure to wear load and decreased wear resistance as the films were too thinner than substrate. Nevertheless the higher substrate bias energy applied to perform the dense films, it wasn't shown benefits about the wear properties from DC sputtering. But, in case of using ABPD sputtering, the wear resistance was largely improved without changing morphology despite of thin films.

• Animal Bioscience
• /
• v.34 no.7
• /
• pp.1243-1252
• /
• 2021

Objective: An experiment was conducted to investigate the continuous and intermittent lighting program effects on terms of the productive performance, carcass traits, blood biochemical parameters, innate immune and oxidative status in broiler chicks. Methods: A total of 600 Cobb-500 one day old chicks were randomly allocated into six equal groups (100 chicks per treated group with five replicates of 20 chicks each) based on lighting program; 22 continuous lighting (22 C), 11 h lighting+1 darkness twice daily (11 L/1 D), 20 h continuous lighting (20 C), 5 h lighting+1 darkness four times daily (5 L/1 D), 18 h continuous lighting (18 C) and the final group subjected for 3 h lighting+1 h darkness six times daily (3 L/1 D). The experimental period lasted 42 days. Results: Compared with those under the intermittent light program, broiler chicks exposed to continuous lighting for 22 h had significant improvement in live body weight and carcass (dressing and breast percentage) measured traits. Though reducing lighting hours significantly reduced feed intake and feed conversion ratio values. Different lighting programs revealed no significant effect on all blood biochemical parameters. Oxidative stress and innate immunity parameters significantly enhance by reducing lighting hours (3L/1D). Conclusion: The findings suggest that reducing lighting hours up to 3L/1D would be more useful in enhancing feed efficiency, innate immunity, and oxidative status compared with continuous lighting programs on broilers.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.2
• /
• pp.67-77
• /
• 2009

In this study, the relations of cone tip resistances (qc) and DMT indices of cemented sand are analyzed from a series of calibration chamber tests. The experimental results show that, with increasing the cementation level, three DMT indices also increase. The CPT and DMT do not appear to properly reflect the cementation effect of sand, since the penetration induces the damage of cementation. Nevertheless, the DMT is more sensitive to deformation characteristics of cemented sand than CPT. It is also observed that the $E_D/q_c$ ratio of cemented sand is larger than that of uncemented sand. However, the $K_D-q_c/{\sigma}_v'$ relation is independant of cementation, unlike the result of previous study. In addition, this study evaluates the constrained modulus and cohesion intercept of cemented sand using the relation between cone resistance and dilatometer constrained modulus ($M_D$).

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.3
• /
• pp.311-318
• /
• 2024

In this paper, a design for a radio frequency(RF) and infrared(IR) absorber with metasurfaces is discussed in microwave frequency bands. The RF absorber includes double layers of metasurfaces to operate in S- and X-bands. Effects of sheet resistance of the metasurfaces and thicknesses of dielectric supporting layers on reflection responses are investigated. An IR stealth layer incorporates an array of conductive grids with slits to reflect IR signals but to transmit RF signals and visible rays. Periodicity of the grids and slits is studied for transmission responses in the X-band and a surface area ratio. Reflection responses of the RF/IR multispectral absorber are found to be lower than -10 dB and -16 dB in the S- and X-bands, respectively, from full-wave simulation. Finally, the RF/IR multispectral absorber is fabricated and its reflection responses are measured to verify designed performance.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.448-454
• /
• 2007

Hydrothermal synthesis was conducted with starting material as Barium hydroxide and hydrous titania ($TiO_2{\cdot}xH_2O$) to obtain barium titanate fine Powder. The conversion, crystal structure and properties of as-prepared powder were investigated according to reaction temperature, time and concentration. The effect of variables on conversion was in order of time < temperature < concentration and the maximum conversion reached to 99.5% in the case of hydrothermal synthesis at $180^{\circ}C$ for 2 h with 2.0 M reactant concentration. At low concentration such as 0.25 M, formation of unreacted $BaCO_3$ and $TiO_2$ was not inevitable at even high reaction temperature and these components converted into $BaTi_2O_5$ at high temperature and remained as impurity. As concentration of reactant increased, the size of as-synthesized $BaTiO_3$ powder deceased and Ba/Ti molar ratio approached into 1, showing Ba/Ti ratio of $1{\pm}0.005$ for reaction at $180^{\circ}C$ for 2 h with 2.0 M concentration.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.7
• /
• pp.962-970
• /
• 2012

This study aimed to investigate the effects of ruminal infusion of garlic oil (GO) on fermentation dynamics, fatty acid (FA) profile, and abundance of bacteria involved in biohydrogenation in the rumen. Six wethers fitted with ruminal fistula were assigned to two groups for cross-over design with a 14-d interval. Each 30-d experimental period consisted of a 27-d adaptation and a 3-d sample collection. Goats were fed a basal diet without (control) or with GO ruminal infusion (0.8 g/d). Ruminal contents collected before (0 h) and at 2, 4, 6, 8, and 10 h after morning feeding were used for fermentation analysis, and 0 h samples were further used for FA determination and DNA extraction. Garlic oil had no influence on dry matter intakes of concentrate and hay. During ruminal fermentation, GO had no effects on total VFA concentration and individual VFA molar proportions, whereas GO increased the concentrations of ammonia nitrogen and microbial crude protein (p<0.05). Compared with control, GO group took a longer time for total VFA concentration and propionate molar proportion to reach their respective maxima after morning feeding. The ratio of acetate to propionate in control reduced sharply after morning feeding, whereas it remained relatively stable in GO group. Fatty acid analysis showed that GO reduced saturated FA proportion (p<0.05), while increasing the proportions of C18, t11-18:1 (TVA), c9,t11-conjugated linoleic acid (c9,t11-CLA), t10,c12-CLA, and polyunsaturated FA (p<0.05). The values of TVA/(c9,t11-CLA+TVA) and C18:0/(TVA+C18:0) were reduced by GO (p<0.05). Real-time PCR showed that GO tended to reduce Butyrivibrio proteoclasticus abundance (p = 0.058), whereas GO had no effect on total abundance of the Butyrivibrio group bacteria. A low correlation was found between B. proteoclasticus abundance and C18:0/(TVA+C18:0) (p = 0.910). The changes of fermentation over time suggested a role of GO in delaying the fermentation process and maintaining a relatively modest change of ruminal environment. The inhibitory effects of GO on the final step of biohydrogenation may be related to its antibacterial activity against B. proteoclasticus and other unknown bacteria involved.

• Journal of Bio-Environment Control
• /
• v.20 no.4
• /
• pp.365-372
• /
• 2011

This study aimed to examine foundational data for container seedling production with the subject of Daphniphyllum macropodum community in Mt. Naejang National Park. To achieve the goal, it investigated the growth characteristics of young tree seedlings growing in places with different light intensity environment. Regarding the growth environment of Daphniphyllum macropodum community, it was typical heavy rain summer climate, and the soil was silt loam with the organic content as 11.42~15.61%, total nitrogen as 0.50~0.76%, cation exchangeable capacity (C.E.C) as 18.92~23.32 cmol/kg, and pH as 4.85~5.58. About light intensity environment changed by research plots, relative transmittance of solar radiation was 71~76% in plot A, 37~42% in plot B, 65~70% in plot C, and 28~33% in plot D. The seedlings tended to be intensively distributed either under the crown of their mother tree or in the slope site, and plot A and C where light intensity environment is relatively more favorable showed 1,550 tree/ha and 1,250 tree/ha. Total biomass production of Daphniphyllum macropodum seedlings was 5.37 g in plot A and 5.29 g in plot C, so they were higher than 4.42~4.51 g in plot B and D with relatively less favorable light intensity environment. The T/R ratio was 1~2, leaf area rate was $139.71{\sim}183.50cm^2{\cdot}g^{-1}$, leaf area ratio was $39.68{\sim}60.66cm^2{\cdot}g^{-1}$, and leaf dry weight ratio grew higher in the range of $0.28{\sim}0.33cm^2{\cdot}g^{-1}$ as the intensity of radiation became less. It is thought that in the generation and growth of Daphniphyllum macropodum seedlings, the intensity of light has more effects than the organic content in soil. And it is also thought that in the application of container seedlings production, light environment management over 65~70% to full sun light intensity will affect significantly the initial growth of Daphniphyllum macropodum.