• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.5
• /
• pp.1-11
• /
• 2021

The purpose of this study is to find out the main factors affecting air quality in urban physical space factors, and provide clues for environmental improvement. Nine monitoring stations in China's industrial city, Changchun, collected AQI concentration data from January 1, 2018 to December 31, 2019. This paper analyzes the types and distribution characteristics of urban physical facilities within a radius of 300m with the detection station as the center. The monitoring station is divided into three groups, and the difference in floating dust concentration among the three groups in different seasons is analyzed. The results show that AQI concentration is the highest in spring and winter, followed by summer, and the lowest in autumn. The place with the highest concentrations of AQI in spring are F (93.00), D (91.10), I (89.20), in summer are D (69.05), A (67.89), B (84.44), in autumn are I (62.80), G (60.84), D (53.27), D (53.27), in winter are I (95.82), H (95.60), f (94.04). Through SPSS analysis, it shows that the air index in a space with a diameter of 600 meters is related to forest land, grassland, bare land, water space, tree height, building area (average value), and building volume (average value). According to the statistical analysis results of spring and winter with the most serious pollution, forest land area (43,637m², 15.44%) and water surface area (18,736m², 6.63%) accounted for the majority, and group 1 (A, B, C) with the least average building area (448m², 0.17%) and average building volume (10,201m²) had the lowest pollution concentration. On the contrary, group 2 (D, E, F) had the highest AQI concentration, with less or no woodland (1,917m², 0.68%) and water surface area (0m², 0%), and the highest average building area (1,056m², 0.37%) and average building volume (17,470m³). It is confirmed that the characteristics of the area with the highest AQI concentration are that the more the site ratio of tree height above 12m, the smaller the site ratio of bare land, and the lower the pollution degree. On the contrary, the larger the area of bare land, the higher the pollution degree. By analyzing the characteristics of nine monitoring stations in Changchun, it can be seen that the air quality brought by the physical characteristics of urban space is closely related to the above factors.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.18 no.5
• /
• pp.455-463
• /
• 1985

Thermal-denaturation of myofibrillar protein of dorsal skeletal muscle from file fish was investigated by measuring denaturation constant($K_D$) and thermodynamic parameters at various temperatures. The protective effects of sucrose, sorbitol and amino acids when added individually or combined were also discussed. The denaturation rate as reflected in inactivation of myofibrillar protein Ca-ATPase was followed the first order reaction. The $K_D$ values at $25^{\circ}C,\;30^{\circ}C,\;and\;35^{\circ}C$ were $19.52{\times}10^{-5},\;112.25{\times}10^{-5},\;and\;247.20{\times}10^{-5}$, respectively. The activation energy of the reaction at $30^{\circ}C$ was 43 kcal/mole. The protective effects of sucrose, sorbitol, glycine, alanine and Na-glutamate were increased with the concentration but the effects of sorbitol and Na-glutamate decreased beyond 1.0 mole. Basic amino acids such as arginine and lysine did not revealed any protective effect on the thermal denaturation. In case of mixed addition, the effects of Na-glutamate to glycine, sorbitol to glycine, and sorbitol to sucrose or sorbitol to Na-glutamate were enhanced 1.2 to 7.0 times as much as that of control (ratio of mixing; 1:1, range of concentration; 0.5 to 1.25 mole). Under the frozen condition at $-20^{\circ}C$, two mixtures such as Na-glutamate to glycine and sorbitol to sucrose apparently revealed the protective effects.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.2
• /
• pp.183-193
• /
• 1995

Assuming that fishing nets are porous structures to suck water into their mouth and then filtrate water out of them, the flow resistance N of nets with wall area S under the velicity v was taken by $R=kSv^2$, and the coefficient k was derived as $$k=c\;Re^{-m}(\frac{S_n}{S_m})n(\frac{S_n}{S})$$ where $R_e$ is the Reynolds' number, $S_m$ the area of net mouth, $S_n$ the total area of net projected to the plane perpendicular to the water flow. Then, the propriety of the above equation and the values of c, m and n were investigated by the experimental results on plane nettings carried out hitherto. The value of c and m were fixed respectively by $240(kg\cdot sec^2/m^4)$ and 0.1 when the representative size on $R_e$ was taken by the ratio k of the volume of bars to the area of meshes, i. e., $$\lambda={\frac{\pi\;d^2}{21\;sin\;2\varphi}$$ where d is the diameter of bars, 21 the mesh size, and 2n the angle between two adjacent bars. The value of n was larger than 1.0 as 1.2 because the wakes occurring at the knots and bars increased the resistance by obstructing the filtration of water through the meshes. In case in which the influence of $R_e$ was negligible, the value of $cR_e\;^{-m}$ became a constant distinguished by the regions of the attack angle $ \theta$ of nettings to the water flow, i. e., 100$(kg\cdot sec^2/m^4)\;in\;45^{\circ}<\theta \leq90^{\circ}\;and\;100(S_m/S)^{0.6}\;(kg\cdot sec^2/m^4)\;in\;0^{\circ}<\theta \leq45^{\circ}$. Thus, the coefficient $k(kg\cdot sec^2/m^4)$ of plane nettings could be obtained by utilizing the above values with $S_m\;and\;S_n$ given respectively by $$S_m=S\;sin\theta$$ and $$S_n=\frac{d}{I}\;\cdot\;\frac{\sqrt{1-cos^2\varphi cos^2\theta}} {sin\varphi\;cos\varphi} \cdot S$$ But, on the occasion of $\theta=0^{\circ}$ k was decided by the roughness of netting surface and so expressed as $$k=9(\frac{d}{I\;cos\varphi})^{0.8}$$ In these results, however, the values of c and m were regarded to be not sufficiently exact because they were obtained from insufficient data and the actual nets had no use for k at $\theta=0^{\circ}$. Therefore, the exact expression of $k(kg\cdotsec^2/m^4)$, for actual nets could De made in the case of no influence of $R_e$ as follows; $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})\;.\;for\;45^{\circ}<\theta \leq90^{\circ}$$, $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})^{1.6}\;.\;for\;0^{\circ}<\theta \leq45^{\circ}$$

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.85-94
• /
• 2013

PURPOSES: The performance of tack coat, commonly used for layer interface bonding, is affected by application rate and curing time. In this study, bonding strength tests were performed according to the application rate and curing time of asphalt emulsion. Based on finding from this study, optimum application rates and curing times are proposed. METHODS: In order to investigate bonding characteristic of asphalt emulsion, tests were performed on both asphalt concrete pavement and portland concrete pavement. Also, asphalt emulsions were tested at the application rate of 0, 0.2, 0.4, 0.6, and $0.8{\ell}/m^2$ and at the curing time of 0, 0.5, 1, 2, and 24 hours. Pull-off test and shear bonding strength test, which commonly used for bonding strength measurement of asphalt emulsion, were adopted for this study. To assess field performance under different testing condition, asphalt emulsions were applied to in-service pavement. Throughout coefficient of determination analysis between material index properties from asphalt emulsion and mechanical response from bonding strength tests, performance correlativity was analyzed. RESULTS: Test results show that optimum application rate for asphalt overlay on asphalt concrete pavement (AOA) and asphalt overlay on concrete pavement (AOC) was $0.4{\sim}0.5{\ell}/m^2$ and $0.3{\sim}0.5{\ell}/m^2$, respectively. According to the curing time increment, tensile strength and shear strength of AOC were increased to 22~44% and 20~39%, respectively. AOA case also show strength increment in tensile strength (42%) and shear strength (9%). We tested the applicability of tack coat materials at the field sites, and our findings demonstrated that the bonding (for D and E) and rapid curing (for B, C, and D, E) performances were superior than others. Among material index properties, there was a high correlation between penetration ratio and bonding strength test result. CONCLUSIONS : Result show that interlayer bonding strength was affected by asphalt emulsion type, application rate and curing time. AOC required slightly higher application ($0.1{\ell}/m^2$) than AOA. Both AOA and AOC cases show higher strength at longer curing time. Up to 2hours of curing, rapid strength increments were observed, but strength increment ratio was decreased after 2hours of curing. From the observed correlation between penetration ratio and bonding strength, it is expected that penetration ratio can be used as one of important factors affecting bonding strength analysis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.12
• /
• pp.1763-1770
• /
• 2011

Fifty-six [(Duroc${\times}$Yorkshire)${\times}$Landrace] pigs with an average initial BW of 19.3${\pm}$0.17 kg were used in this 15-wk growth experiment to investigate the effects of grape pomace fermented by Saccharomyces boulardii on pig growth performance, nutrient digestibility and quality attributes of pork. Pigs were allotted to 2 dietary treatments (7 replications) based on their initial BW in a randomized complete block design. The experimental treatments were: i) control (CON; basal diet), ii) FGPP (CON+30 g/kg fermented grape pomace product). Dietary FGPP improved (p<0.05) average daily gain (ADG), coefficient apparent total tract digestibility (CATTD) of dry matter (DM) and nitrogen (N) during 35-70 d of the experiment. Similarly, pigs fed the FGPP supplemented diet had a higher N digestibility (p<0.05) in the finisher phase (day 71-105). Dietary FGPP increased (p<0.05) the marbling score, the redness ($a^*$) and yellowness ($b^*$) values, as well as the anti-oxidative ability (lower TBARS). The inclusion of FGPP reduced palmitic acid (C:16:0), stearic acid (C:18:0), arachidic acid (C:20:0) and SFA levels (p<0.05) in subcutaneous fat. An increased (p<0.05) linoleic acid (C18:2n6), total PUFA and PUFA/SFA ratio were observed in the FGPP group. Dietary FGPP supplementation decreased the arachidic acid (C:20:0) level in longissimus muscle (LM). In conclusion, dietary inclusion of FGPP at the level of 30 g/kg improved the growth performance, nutrients digestibility and altered the fatty acid pattern in the subcutaneous fat as well as some attributes of pork meat.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.1
• /
• pp.17-27
• /
• 2017

This study evaluated the performance of bedding fabrics consisting of warp (150d/144f, polyester) and weft (polyester, Tencel and cotton MVS blended spun yarn) with blend ratio of weft. We measured electrostatic propensity, moisture properties, pilling properties and mechanical properties of the fabrics for this study. F-P fabric showed outstanding moisture properties and pilling properties. However, tensile properties and electrostatic propensity were relatively inferior to other characteristic values. Significant static electricity may make F-P fabric uncomfortable. F-P7C3 fabric showed outstanding moisture properties and pilling properties. Static electricity may make F-P7C3 fabric uncomfortable; in addition, F-P5C5 fabric showed outstanding moisture properties and pilling properties. Rough and stiff hand feel were expected to increase because tensile properties decreased and surface properties increased. F-C fabric showed outstanding pilling properties and electrostatic propensity. However, it showed inferior moisture control properties. F-P5T4C1 fabric showed outstanding moisture properties, pilling properties and electrostatic propensity. Several properties are outstanding; however, the hand feels are very rough and stiff from bending. The water evaporation and static electricity increased with increasing polyester content. As the content of cotton increased, tensile properties were improved. However, water evaporation and static electricity decreased. The addition of Tencel increased the thickness and compression energy so that it exhibited a soft characteristic upon compression and an excellent moisture control properties, but the surface became somewhat coarse.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.1
• /
• pp.86-90
• /
• 2006

This study was carried out to determine the effects of free choice feeding of starter feed and whole cereals on the growth of turkey poults. Two hundred-seventy poults (7-d old) were divided into 3 treatment groups each with 3 replications containing 15 males and 15 females. Control poults (C) were fed only on starter feed (280 g CP and 11.7 MJ ME/kg). Treatments for choice-fed turkey poults were offered a choice of a starter feed and wheat (120 g CP and 12.3 MJ ME/kg) for wheat selecting (WS) or maize (83 g CP and 13.9 MJ ME/kg) for maize selecting (MS) group in separate feeders. Final live weight (2,280.7 g for the C vs. 2,374.3 and 2,324.6 g for the WS and MS), daily gain (39.21 g vs. 40.87 and 39.99 g) and total feed intake (95.2 g vs. 103.2 and 97.9 g) in the WS poults were significantly higher (p<0.05) than those of the C group, but feed conversion ratio was not significantly different between the treatments. The proportional intakes of cereals vs. total feed intake were 11% in both the WS and MS group. The amount of protein intake in the C group (280 g CP/kg diet) was significantly (p<0.05) higher than that in WS and MS groups (263 and 259 g CP/kg diet, respectively) whilst the ME intake in the C group (11.7 MJ/kg diet) was significantly (p<0.05) lower than that in MS group (11.9 MJ/kg diet). Our results showed that turkey poults fed starter feed and whole wheat in a free choice feeding system have a higher efficiency in terms of daily gain, final live weight, and an economic advantage may be obtained from free choice feeding due to a reduced protein intake and feed cost.

• The Journal of the Acoustical Society of Korea
• /
• v.6 no.4
• /
• pp.55-63
• /
• 1987

Modified $PbTiO_3$ piezoelectric ceramics added with 0.2, 0.25, 0.3 mol of $CaCO_3$ and 0.04 mol of $(Co_{\frac{1}{2}}W_{\frac{1}{2}})$ and 0.05 mol of $MnO_2$ and NiO have been fabricated. These ceramics can be poled sufficiently within 10 minutes at $100^{\circ}C$ under about d.c. field of 40 kv/cm. Detailed measurement was performed on dielectric constants, cutie temperatures, elastic and piezoelectric properties and coupling factors for the fabricated ceramics. The most value of the piezoelectric coupling factors was coupling factor of thickness mode kt and its value for 0.25 mol of Ca was about $45\%$. Dielectric constants of $\varepsilon_{33}^T$ and $\varepsilon_{11}^T$ for 0.25 mol of Ca were 242 and 260, and coupling factor ratio (kt/Kp) and Qm were 6 and 357 respectively.

• Bulletin of the Korean Chemical Society
• /
• v.8 no.2
• /
• pp.69-72
• /
• 1987

The structures of dehydrated $Ag_9Cs_3$-A treated with hydrogen gas at three different temperatures have been determined by single-crystal X-ray diffraction techniques. Their structures were solved and refined in the cubic space group Pm3m at 23(1) $^{\circ}C$. All crystals were ion exchanged in flowing streams of aqueous $AgNO_3$/$CsNO_3$ with a mole ratio 1:3.0 to achieve the desired crystal composition. The structures treated with hydrogen at $23^{\circ}C(a=12.288(1)\;{\AA})\;and\;310^{\circ}C(a=12.291(2)\;{\AA})$ refined to the final error indices R1 = 0.091 and R2 = 0.079, and 0.065 and 0.073, respectively, using the 216 and 227 reflections, respectively, for which I >3${\sigma}$(I). In both of these structures, eight $Ag^+$ ions are found nearly at 6-ring centers, and three $Cs^+$ ions lie at the centers of the 8-rings at sites of $D_{4h}$ symmetry. One $Ag^{\circ}atom$, presumably formed from the reduction of a $Ag^+$ ion by an oxide ion of a residual water molecule or of the zeolite framework during the dehydration process, is retained within the zeolite, perhaps in a cluster. In these two structures hydrogen gas could not enter the zeolite to reduce the $Ag^+$ ions because the large $Cs^+$ ions blocked all the 8-windows. However, hydrogen could slowly diffuse into the zeolite and was able to reach and to reduce about half of the $Ag^+$ ions in the structure only at high temperature ($470^{\circ}C$). The silver atoms produced migrated out of the zeolite framework, and the protons generated led to substantial crystal damage.