• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.5
• /
• pp.253-259
• /
• 2003

In this study, to find out the reason of deterioration in surface roughness of steel and cast iron after Tufftride, it has been investigated on the relation between the surface roughness and various factors such as the evolution of compound layer, surface morphology, and surface hardness, and change of pore ratio in the compound layer during Tufftride at $580^{\circ}C$. It is found that the surface roughness was increased with the evolution of compound layer during Tufftride of steel and cast iron. The change of surface roughness after Tufftride was reduced with decreasing tho content of carbon and cementite ($Fe_3C$) in the materials. in the cast irons, the various shaped graphites that was exposed to the surface should induce the discontinuous growth of the compound layer, and this resulted in the incoherent interfaces between matrix and compound layer and the deterioration of surface roughness. In the steels, the existence of cementites in the matrix resulted in the incoherent interfaces between matrix and compound layer. It is considered that during Tufftride the surface roughness must be mainly influenced by the formation of the incoherent interface between compound layer and matrix that is affected by some factors such as the microstructure, the composition, and the hardness of the matrix.

• Korean Journal of Materials Research
• /
• v.23 no.1
• /
• pp.47-52
• /
• 2013

Graphene has been synthesized on 100- and 300-nm-thick Ni/$SiO_2$/Si substrates with $CH_4$ gas (1 SCCM) diluted in mixed gases of 10% $H_2$ and 90% Ar (99 SCCM) at $900^{\circ}C$ by using inductively-coupled plasma chemical vapor deposition (ICP-CVD). The film morphology of 100-nm-thick Ni changed to islands on $SiO_2$/Si substrate after heat treatment at $900^{\circ}C$ for 2 min because of grain growth, whereas 300-nm-thick Ni still maintained a film morphology. Interestingly, suspended graphene was formed among Ni islands on 100-nm-thick Ni/$SiO_2$/Si substrate for the very short growth of 1 sec. In addition, the size of the graphene domains was much larger than that of Ni grains of 300-nm-thick Ni/$SiO_2$/Si substrate. These results suggest that graphene growth is strongly governed by the direct formation of graphene on the Ni surface due to reactive carbon radicals highly activated by ICP, rather than to well-known carbon precipitation from carbon-containing Ni. The D peak intensity of the Raman spectrum of graphene on 300-nm-thick Ni/$SiO_2$/Si was negligible, suggesting that high-quality graphene was formed. The 2D to G peak intensity ratio and the full-width at half maximum of the 2D peak were approximately 2.6 and $47cm^{-1}$, respectively. The several-layer graphene showed a low sheet resistance value of $718{\Omega}/sq$ and a high light transmittance of 87% at 550 nm.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5D
• /
• pp.513-522
• /
• 2010

Underground construction for traffic networks, complexes, and storage facilities has risen as an effective land use plan for dealing with emerging problems such as overcrowded urban cities and traffic jams. This paper performed an economic feasibility analysis of the development of the integrated field management system which provides field workers and managers with 3D-based location tracking and clear communication during underground construction works. To conduct the analysis, processes and problems of field management for underground construction were analyzed and deduction in accidents and field management costs and productivity improvement were estimated as expected benefits. Based on computed benefits and costs, an economic analysis was conducted using Benefit/Cost ratio(B/C), Net Present Value(NPV), and Internal Rate of Return(IRR) and then sensitivity analysis was performed to cope with the uncertainty of assumed variables.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.41-47
• /
• 2022

Ag sintering technologies have received great attention as it was applied to the inverter of Tesla's electric vehicle Model III. Ag sinter bonding technology has advantages in heat dissipation design as well as high-temperature stability due to the intrinsic properties of the material, so it is useful for practical use of SiC and GaN devices. This study was carried out to understand the sinter joining temperature effect on the robust Ag sintered joints in air without pressure within 10 min. Electroplated Ag finished Cu dies (3 mm × 3 mm × 2 mm) and substrates (10 mm × 10 mm × 2 mm) were introduced, respectively, and nano Ag paste was applied as a bonding material. The sinter joining process was performed without pressure in air with the bonding temperature as a variable of 175 ℃, 200 ℃, 225 ℃, and 250 ℃. As results, the bonding temperature of 175 ℃ caused 13.21 MPa of die shear strength, and when the bonding temperature was raised to 200 ℃, the bonding strength increased by 157% to 33.99 MPa. When the bonding temperature was increased to 225 ℃, the bonding strength of 46.54 MPa increased by about 37% compared to that of 200 ℃, and even at a bonding temperature of 250 ℃, the bonding strength exceeded 50 MPa. The bonding strength of Ag sinter joints was directly influenced by changes in the necking thickness and interfacial connection ratio. In addition, developments in the morphologies of the joint interface and porous structure have a significant effect on displacement. This study is systematically discussed on the relationship between processing temperatures and bonding strength of Ag sinter joints.

• Korean Journal of Radiology
• /
• v.21 no.11
• /
• pp.1220-1229
• /
• 2020

Objective: Stereotactic vacuum-assisted breast biopsy (VABB) is considered a reliable alternative to surgical biopsy for suspicious calcifications. In most cases, the management of flat epithelial atypia (FEA) and atypical ductal hyperplasia (ADH) after VABB with residual calcifications requires surgical excision. This study aimed to evaluate the impact of pathology of non-calcified specimens on the underestimation of malignancy. Materials and Methods: We retrospectively reviewed 1147 consecutive cases of stereotactic VABB of suspicious calcifications without mass from January 2010 to December 2016 and identified 46 (4.0%) FEA and 52 (4.5%) ADH cases that were surgically excised for the retrieval of residual calcifications. Mammographic features and pathology of the calcified and non-calcified specimens were reviewed. Results: Seventeen specimens (17.3%) were upgraded to malignancy. Mammographic features associated with the underestimation of malignancy were calcification extent (> 34.5 mm: odds ratio = 6.059, p = 0.026). According to the pathology of calcified versus non-calcified specimens, four risk groups were identified: Group A (ADH vs. high-risk lesions), Group B (ADH vs. non-high-risk lesions), Group C (FEA vs. high-risk lesions), and Group D (FEA vs. non-high-risk lesions). The lowest underestimation rate was observed in Group D (Group A vs. Group B vs. Group C vs. Group D: 35.0% vs. 20.0% vs. 15.0% vs. 3.6%, p = 0.041, respectively). Conclusion: Considering that the calcification extent and pathology of non-calcified specimens may be beneficial in determining the likelihood of malignancy underestimation, excision after FEA or ADH diagnosis by VABB is required, except for the diagnoses of FEA coexisting without atypia lesions in non-calcified specimens.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.261-265
• /
• 2007

Carbide-derived carbon coating has been synthesized by low temperature treatment of TiC disk with $H_2/Cl_2$ mixture gases. A variety of physical measurements indicated that Ti was extracted and carbon layer was formed by exposure of $Cl_2$ gas. The $I_D/I_G$ ratio increased with increasing $Cl_2$ gas concentration. Wear coefficient and frictional coefficient varied with $Cl_2$ gas concentration. When the $Cl_2$ gas concentration decreased to 3.3 vol%, the friction coefficient approach a minimum. The results showed that degree of graphite crystallinity and variation of porosity due to the $Cl_2$ gas content were responsible for different tribology performance.

• 전자공학회논문지 IE
• /
• v.47 no.2
• /
• pp.32-37
• /
• 2010

In this study, to develop union type SMD inductor core needs to have the desire of super miniaturization and high reliability, it analyzed temperature properties due to electric power value. As the temperature of electronic parts rise, it bring to technical obstacles that parts can not normal operation, it reduce the span of life to raise the fault ratio. Also, it impact to the parts by heat change power and expansive power, it can not behave exactly, and it have an effect on reliability. It measured the difference value between conditional temperature and parts temperature to union type SMD inductor core. As the results of simulation using D.C. current and resistor($R_dc$), it obtained the excellent regular current values at rising temperature of 40[$^{\circ}C$].

• Journal of Power System Engineering
• /
• v.5 no.3
• /
• pp.80-87
• /
• 2001

Decorative properties of chromium depositions from oxalic acid bath containing chromium oxide and ammonium sulfate have been examined over a wide range of bath compositions and plating conditions. The obtained results from this experiment are summarized as follow: The followings were determined as a optimum conditions, bath compositions; $CrO_3\;200{\sim}250\;g/{\ell},\;H_2C_2O_4{\cdot}2H_2O\;500{\sim}700\;g/{\ell},\;(NH_4)_2SO_4\;40{\sim}120\;g/{\ell}$, and operation conditions; pH $2.0{\sim}2.5$, current density $15{\sim}250\;A/dm^2$ at bath temperature range of $30{\sim}80^{\circ}C$. Bright chromium deposits were obtained over a wide range of ammonium sulfate concentration and bath temperature. Decorative property for chromium deposition was adopted to apply stoichiometric ratio of $CrO_3$ concentration and $H_2C_2O_4{\cdot}2H_2O$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.602-603
• /
• 2008

The design modification of problematic component in a given vibration path is disallowed in order to sacrifice other performances such as ride comport or handling of a vehicle. For this, the paper presents a new contribution analysis based on transmissibility ratio (TR) of acceleration in a definite vibration path to find a proper candidate for design modification. The new contribution analysis is based on the fact that the sensitivity of TR over a small design change is inversely proportional to the magnitude of TR. The new methodology can significantly relieve efforts of time-consumming modal analysis for detail modal information. The theory of proposed contribution analysis is simulated with five-degree-of-freedom open vibration path and confirms that the contribution result is well matched with the variance of TR over a dynamic change on a vibration path.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.5
• /
• pp.45-52
• /
• 2014

Torrefaction and hydrothermal carbonization (HTC) are productive methods to reclaim energy from lignocellulosic biomass. The hydrophobic, homogenized, energy dense and carbon rich solid fuel can be obtain from torrefaction and hydrothermal carbonization. Dead leaves were carbonized in a stainless steel reactor of volume 200 ml with torrefaction ($250-270^{\circ}C$) for 120 minutes and hydrothermal carbonization ($200-250^{\circ}C$) for 30 minutes, with mass yield solid fuel ranging from 57-70% and energy content from 16.81MJ/kg to 22.01 MJ/kg compare to the biomass. The char produced from torrefaction process possess high energy content than hydrothermal carbonization. The highest energy yield of 89.96% was obtained by torrefaction at $250^{\circ}C$. The energy densification ratio fluctuated in between 1.15 to 1.30. On the basis of pore size distribution of the chars, the definition of the International Union of Pure and Applied Chemistry (IUPAC) was used as a classification standard. The pore diameter was ranging within 11.09-19 nm which play important role in water holding capacity in soil. Larger pores can hold water and provide passage for small pores. Therefore, it can be concluded that high pore size char can be obtained my HTC process and high energy content char of 22.01 MJ/Kg with 34.04% increase in energy can be obtain by torrefaction process.