• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.621-630
• /
• 2006

Twelve beams made of lightweight high-strength concrete were tested to determine their diagonal cracking and ultimate shear capacities. A total of 12 beams without(4 beams) and with lightweight(8 beams) were tested in a stiff testing facility, and complete load-midspan deflection curves, including the maximum capacities portion, were obtained. The variables in the test program were concrete strength, which varied 35.4 MPa, 65.3 MPa; shear span-depth ratios a/d=1.5, 2.5, 3.5, 4.5; and tensile steel ratio between 0.57 and 2.3 percent. Also, we divided beam by diagonal tension crack and ultimate shearing strength to propose an equation. In addition, it analyzed comparison mutually applying existing proposal and guide. $V_{cr}$ was as result that AIK recommendations and Zsutty proposal decrease more than a/d=2.5, increased some in Mathey's proposal equation. $V_{cr,\exp}/V_{cr,cal}$ showed tendency of overestimation according to increase of tensile steel ratio and compressive strength of concrete. On the other hand, $V_{cr,\exp}/V_{cr,cal}$ is superior in conformability with an experiment result Zsutty's proposal among other equations. The proposal equation hew that expect $V_{cr}/V_u$, rationally about shearing strength. Therefore, shear strength an equation is considered to be utilized usefully evaluating capacity by change of the shear span depth ratio of lightweight concrete, tensile steel ratio, and compressive strength of the concrete in this research.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.7
• /
• pp.585-592
• /
• 2015

Effects of opening distance on liquid-gas spray of pintle injector were experimentally investigated under atmospheric condition by using water and air as simulants of propellants. Discharge coefficients($C_d$) and mass flow rates were calculated with various injection conditions; 0.1 bar - 1.0 bar for water pressures and 0.2 mm - 1.0 mm for the pintle opening distances. Spray angles were measured from the spray images that were obtained by a shadowgraphy method. When opening distance is 0.2 mm, liquid sheet is not formed properly and it show non-uniform spray. than it can result in combustion instability. it has a weak correlation between the momentum flux ratio and the spray angle, while it has a strong correlation between the momentum ratio and spray angle. Finally the spray angles reduced exponentially when the momentum ratio increased and the spray angles converged to about 40 degrees.

• The Korean Journal of Nuclear Medicine
• /
• v.31 no.3
• /
• pp.365-371
• /
• 1997

The aim of this study is to evaluate the efficiency of the pulmonary perfusion scan(Pp scan) in the experimental animal single lung transplantation. Eight left lung transplanted mongrel dogs were included in this study. The serial Pp scan with 111MBq $^{99m}TC-MAA$ were done at the periods of immediate postoperative period, POD 3 days, and POD 10-14 days and finally autopsy was done in each cases. The transplanted lung perfusion was analysed as a percentage radioactivity of trans planted/native lung(T/N) ratio. The Pp scan of a donor mongrel dog was used as a reference(left/right lung (T/N) ratio 85.2%). The average T/N ratio of all cases on immediate postoperative state(reperfusion injury) : 19.2%, three acute rejections. 12.6%, three bronchial dehiscences 6.1% and two pulmonary thromboses : 2.0%. Two cases showed moderate improvement of reperfusion injury as increasing the T/N ratio in POD 3 days Pp scan. The T/N ratio showed sequentially decreased in six cases. As a conclusion, the Pp scan could be a non-invasive method in the evaluation of the experimental one-lung transplanted mongrel dog.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.8 no.1
• /
• pp.15-21
• /
• 2008

The district unit planning (DUP) in Korea is a planning instrument. One of the key methods is the incentive system focused on the mitigation of the financial charge of business proprietors with use of various planning deregulation. Here in this paper, it is examined whether the incentive system is indiscriminately applied not only in the metropolitan cities but also in the rural cities. The analysis is carried out with six indicators in relation to the effect on the incentive system on the market of Apartment Housing Development. The indicators are a. the building-to-land ratio(BLR), b. the floor area ratio(FAR) c. the publicly assessed value of land(PAVL), d. the sale price of land(SPL), e. the sale/lease price of apartment house(SLPH) and f. the ratio of housing subscription(RHS). The final result is that the incentive system has different effects between metropolitan cities and rural cities. One of reasons lies on the too high FAR in rural cities to be given basically. Another reason lies on the difference between the cost for purchasing public installation and the profit of the sale & lease price of apartment house. In rural cities their difference becomes much narrow. Finally, the low ratio of housing subscription(RHS) in rural cities makes the effect of the incentive system nearby meaningless.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1091-1094
• /
• 2004

High-luminous efficiency full-color emissions in photoluminescence (PL) were obtained in $GdVO_4$ phosphor thin films co-doped with various amounts of Eu, Er and/or Tm and postannealed at approximately 1000$^{\circ}C$. The $GdVO_4$:Eu,Er,Tm phosphor thin films were deposited on thick $BaTiO_3$ ceramic sheets by r.f. magnetron sputtering using powder targets and postannealed in an air atmosphere. The rare earth (RE) content (RE/(Gd+V+RE) atomic ratio) in the oxide phosphor thin films was varied in the range from 0.1 to 2 at.%. It was found that the excitation of $GdVO_4$:Eu.Er,Tm thin films is attributed to band-to-band transition. A white PL emission was obtained in a $GdVO_4$:Eu,Er,Tm thin film with Eu, Er and Tm contents of 0.2, 0.7 and 1 at.%, respectively: CIE chromaticity color coordinates. (X=0.352 and Y=0.351). In addition, a white emission was obtained in a thin-film electroluminescent (TFEL) device made with this thin film.

• Journal of Information Display
• /
• v.12 no.3
• /
• pp.115-119
• /
• 2011

Optically isotropic liquid crystal (LC) mixture such as blue-phase LC and nanostructured LC composites exhibit the advantages of fast response time, high contrast ratio and wide-viewing angle due to the induced birefringence along the horizontal electric field. Utilizing this mixture, a novel single cell gap in-plane switching-type polymer-stabilized blue-phase transflective liquid crystal display by embedding the nanowire grid polarizer as a polarization-dependent reflective polarizer in the R region is proposed. This device can be used as a normal black mode without any quarter-wave plate or patterned in-cell phase retarder. Moreover, the transmittance is identical to the reflectance so that it will be suitable for single gamma driving. Detailed electro-optic performances, such as voltage-dependent light efficiency and viewing angle of the proposed device configuration, are investigated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.1
• /
• pp.51-58
• /
• 1991

Corrosion fatigue test was performed by the use of plane bending fatigue tester in marine environment having various specific resistance from 25(natural sea water) to 5000.ohm.cm. It is in order to investigate the effects of marine environmental factor on the corrosion fatigue fracture of SS41 steel. The main results obtained are as follows; 1. The aspect ratio(b/a) of corner crack growing in natural sea water is lower than that in air. 2. The surface crack growth rate(da/dN) in marine environment is faster than that in air and da/dN delaies with the specific resistance increased. 3. The experimental constant m of paris rule [da/dN=C(${\delta}$K)$^m$] decrease with the specific resistance decreased and the effect of corrosion in proportion to the specific resistance is more sensitive than that of stress intensity factor range(${\delta}$K) under region II. 4. The accelerative factor(${\alpha}$) in marine environment is about 1.1-2.7 and .alpha. is increase under the low region of stress intensity factor range(${\delta}$K). 5. The electrode potential($E_0$) gets less noble potential with the specific resistance decreased.

• Journal of Biosystems Engineering
• /
• v.32 no.5
• /
• pp.309-315
• /
• 2007

This study was performed to develop a simulation model of circulating concurrent-flow rice dryer. The simulation model consists of drying model, tempering model and crack prediction model. The drying and tempering models were developed based on mathematical analysis, and the crack prediction model was developed by thin layer drying tests. Rice drying tests were done with three replications by use of a pilot scale dryer of holding capacity of 700 kg. Experimental values for moisture content, rice temperature, rice crack, and drying energy were compared with predicted values by simulation model. The RMSEs of predicted moisture contents were ranged from 0.5807% (d.b.) to 1.1951% (d.b.). and the coefficients of determination were 0.9688 to 0.9812. The RMSEs of predicted rice temperatures at the exit of the drying chamber were 1.83 to $3.81^{\circ}C$ and the coefficients of determination were 0.8834 to 0.9482. The results for moisture contents and rice temperatures showed very good relationships between predicted values and experimental values. The RMSEs of predicted value of crack ratio were 0.4082 to 0.7967% and the coefficients of determination were 0.8742 to 0.9547.

• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.126-134
• /
• 2018

Using aqueous solution free radical polymerization with glacial acrylic acid (GAA), maleic anhydride (MA) and sodium methallyl disulfonate (SMADS), a novel linear polycarboxylate dispersant was synthesized for ceramics. Dispersant linear structural characterization was done by FTIR, $^1H$ NMR, HPLC and GPC, and the ratio of monomers was determined using an orthogonal experiment. This research is focused on the effects of polymerization temperature, monomer mole ratios and dosage of initiator on ceramic slurry viscosity with linear polycarboxylate dispersant for ceramic dosage rate of 0.30% (based on dry slurry), all of which were investigated by single factor test. The best polymerization conditions for linear GAA-MA-SMADS are when n(AA) : n(MA) : n(SMADS) equals 3.0 : 1.0 : 0.5, the molecular weight of the polymer is 4600 daltons, the initiator sodium persulfate accounts for 7% of the total mass of polymerized monomers, the polymerization temperature is $90^{\circ}C$ and the reaction time is 2 h. The ceramic body slurry viscosity drops from $820mPa{\cdot}s$ to $46mPa{\cdot}s$ when the concentration of the polycarboxylate dispersant is 0.30%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1626-1635
• /
• 1997

It is important to ensure the reliability of the first localized reactor vessel steel. To satisfy with this purpose, a study on the impact/hardness, low cycle fatigue(LCF), crack growth rate(da/dN) and fracture toughness( ) of base material(BM) and weld metal(WM) were performed under room temperature air and corrosion conditions. A summary of the results is as folows : (1) Charpy impact absorbed energy of BM was the highest value, heat affected zoon(HAZ) and the lowest, WM. The hardness of BM was similar to HAZ. (2) Coefficients of Manson equation using the monotonic tensile test data were obtained for the present material. (3) The effects of stress ratio and ambient (120.deg. C and NaCl) condition on da/dN were investigated, da/dN with NaCl condition expressed the highest value. (4) The results of Charpy V-notch impact test had good correlation with $K_{IC}$ characteristics and the lowest curve of $K_{IC}$ for BM was derived, more researches about WM and HAZ are required hereafter.