• 한국전기전자재료학회논문지
• /
• 제14권10호
• /
• pp.785-791
• /
• 2001

High dielectric (Ba, Sr) TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of Cl$_2$/Ar mixing ration. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400 $\AA$/mim and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. Etching products were redeposited on the surface of BST and resulted in varying the nature of crystallinity. Therefore, we investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS) atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The morphology of the etched surfact was analyzed by AFM. A smoothsurface(roughness ~2.8nm) ws observed under Cl$_2$(20)/Ar(80), rf power of 600 W, dc bias voltage of -250 V and pressure of 10 mTorr. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystallinities of the etched BST film under Ar only and Cl$_2$(20)/Ar(80) were maintained as similar to as-deposited BST. However, intensity of BST(100) orientation under Cl$_2$ only plasma was abruptly decreased. This indicated that CI compounds were redeposited on the etched BST surface and resulted in changed of the crystallinity of BST during the etch process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.244-247
• /
• 2002

NdBaCuO thin films were prepared on $SrTiO_{3}$ substrates by RF magnetron sputtering. These as-grown films were classified into 3type. The resistivity of the deposited films are usually lower than of the YBCO film. The Tc (onset) and Tc (R=0) in the optimized thin films are as high as 90 and 80K, respectively. These as-grown films are highly uniform and semi-trans parent and have a room temperature resistivity of $0.3m{\Omega}cm$.

• 대한화학회지
• /
• 제37권7호
• /
• pp.683-686
• /
• 1993

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.5-6
• /
• 2006

Using the $(Ba_{0.5}Sr_{0.5}){TiO_3}$(BST) powders prepared by the Sol-Gel method, the EST thick films were fabricated on the ${Al_2}{O_3}$ substrates coated with Pt by the screen printing method. Compared with pure EST thick films, the structural and dielectric properties of the EST thick films doped with 1${\sim}$10 wt % MgO were investigated. It was observed that the Mg substitution into EST causes a shift in the cubic-tetragonal EST phase transition peak to a lower temperature. The microstructure of the EST substituted with Mg was homogeneous and dense. Mg substitution into EST had a significant effect on the grain size reduction. Dielectric constant was decreased with increasing the MgO content and temperature. In the case of EST thick films doped with 1 wt% MgO, the relative permittivity and dielectric loss were 158] and 1.4 % at 1 MHz.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.592-597
• /
• 2000

In this study (B $a_{0.5}$/S $r_{0.5}$)Ti $O_3$[BST(50/50)] ceramic thin films were prepared by the Sol-Gel method BST(50/50) stock solution was made and spin-coated on the Indium Tin Oxide(ITO)/glass substrate at 4000 rpm for 30 seconds. The coated films were dried at 35$0^{\circ}C$ for 10 minutes and annealed at 650~75$0^{\circ}C$ for 1 hour. The microstructural properties of the BST(50/50) thin film were studied by the XRD and AFM. The ferroelectric perovskite phase was formed at the annealing condition of 75$0^{\circ}C$ for 1 hour. Dielectric constant and loss of this thin were 370, 3.7% at room temperature respectively. The polarization switching voltage showed the good value of 3V. The leakage current density of the BST(50/50) thin film was 10$^{-7A}$c $m^2$with applied voltage of 1.5V. BST(50/50) thin film capacitors having good dielectric and electrical properties are expecting for the application to the dielectric material of DRAM.RAM.M.

• 한국재료학회지
• /
• 제33권11호
• /
• pp.465-474
• /
• 2023

The effects of La³⁺ substitution for Sr²⁺-site on the crystal structure and the dielectric properties of (Ba_0.7Sr_0.3-3x/2La_x) (Ti_0.9Zr_0.1)O₃ (BSLTZ) (0.005 ≤ x ≤ 0.02) ceramics were investigated. The structural characteristics of the BSLTZ ceramics were quantitatively evaluated using the Rietveld refinement method from X-ray diffraction (XRD) data. For the specimens sintered at 1,550 ℃ for 6 h, a single phase with a perovskite structure and homogeneous microstructure were observed for the entire range of compositions. With increasing La³⁺ substitution (x), the unit cell volume decreased because the ionic size of La³⁺ (1.36 Å) ions is smaller than that of Sr²⁺ (1.44 Å) ions. With increasing La³⁺ substitution (x), the tetragonal phase fraction increased due to the A-site cation size mismatch effect. Dielectric constant (ε_r) increased with the La³⁺ substitution (x) due to the increase in tetragonality (c/a) and the average B-site bond valence of the ABO₃ perovskite. The BSLTZ ceramics showed a higher dielectric loss due to the smaller grain size than that of (Ba_0.7Sr_0.3)(Ti_0.9Zr_0.1)O₃ ceramics. BSLTZ (x = 0.02) ceramics met the X7R specification proposed by the Electronic Industries Association (EIA).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.165-166
• /
• 2008

$(Ba_{0.6},Sr_{0.3},Ca_{0.1})TiO_3$ powders, which were prepared by sol-gel method using a solution of Ba-acetate, Sr-acetate and Ca-acetate and Ti iso-propoxide, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen-printing techniques on high purity alumina substrates. The structural and dielectirc properties were investigated for various $Pr_2O_3$ and $Y_2O_3$doping contents. As a result of thermal analysis of $(Ba_{0.6},Sr_{0.3},Ca_{0.1})TiO_3$ powders, the exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All BSCT thick films, sintered at $1420^{\circ}C$ for 2h, showed the typical XRD patterns of perovskite polycrystalline structure. The average grain size of the specimens decreased with amount of $Pr_2O_3$ and $Y_2O_3$ contents.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 기술교육전문연구회
• /
• pp.66-70
• /
• 2003

This dissertation is about the development of $BaTiO_{3}$-type PTC(Positive Temperature Coefficient) thermistor by composition method. PTC samples were fabricated after setting the experimental composition equation as $(Ba_{0.95-x}Sr_{0.05}Ca_x)TiO_3\;-\;0.01TiO_2\;-\;0.01SiO_2\;-\;aMnCO_3\;-\;0.2Nb_{2}O_{5}$ and their testing results were analyzed. a PTC thermistor, having the characteristics of relatively low resistance at room temperature and c and a good temperature coefficient, has been developed.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.52-52
• /
• 2003

Gbit급 DRAM 커패시터의 고유전물질로 각광받고 있는 (Ba,Sr)TiO$_3$〔BST〕의 하부전극 물질로서 (Ba,Sr)RuO$_3$〔BSR〕의 적용 가능성을 연구하였다. BSR은 BST와의 구조적, 화학적 유사성으로 인하여, BST와 하부전극사이의 저유전 계면반응 충의 생성을 최소화함으로서 향상된 전기적 특성을 구현 할 수 있다. 본 연구에서는 methoxyethoxytetramethylheptanedionate(METHD) 소스를 적용한 유기 화학 기상 증착법(MOCVD)법을 이용하여 BSR을 증착하였으며, 증착된 BSR의 특성을 x-ray photoelectron spectroscopy(XPS) 분석법으로 기화기 온도 변화에 따른 BSR박막의 특성을 분석하였다. 증착온도 55$0^{\circ}C$에서 소스의 기화효율에 영향을 미치는 기화기온도를 변화시켜가며 BSR박막의 증착실험을 진행하였으며 소스 유입 속도 0.075sccm, 증착 온도 55$0^{\circ}C$, Ar/O2 = 200/350 sccm일 때 기화기 온도를 260~28$0^{\circ}C$까지 1$0^{\circ}C$간격의 변화로 증착실험을 수행하였다.

• 센서학회지
• /
• 제18권5호
• /
• pp.343-348
• /
• 2009

$NiO{\cdot}(Co_{0.25}Mn_{0.75})_2O_3$(Mn-Ni-Co) and $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thick films were screen printed on Pt patterned alumina substrate to investigate the effects of sintering temperature on humidity and temperature sensing properties of ceramic sensors. A raise in sintering temperature increased resistance and B constant of the Mn-Ni-Co temperature sensor. This may have derived from the synergic effects of the reduction in charge carriers caused by the substitution of Co for Mn as well as the formation of microcracks from the difference in thermal expansion coefficients. Dependence of resistance on humidity of the Mn-Ni-Co temperature sensor, however, was not found. BST films sintered at temperatures in the range of $1100^{\circ}C$ to $1150^{\circ}C$ showed excellent humidity sensing properties. The BST humidity sensor was faster in its response than the Mn-Ni-Co temperature sensor. The humidity sensor, however, proved to be unstable under various temperatures, suggesting a need for a temperature stabilizing device. In contrast, the Mn-Ni-Co temperature sensor was stable under humid conditions.