• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권3호
• /
• pp.219-227
• /
• 2016

Numerical simulation based on the Reynolds Averaged Naviere-Stokes (RANS) Computational Fluid Dynamics (CFD) method had been carried out with the commercial code ANSYS CFX. The structured grid and SST $k-{\omega}$ turbulence model had been adopted. The impact of non-condensable gas (NCG) on cavitation performance had been introduced into the Schnerr and Sauer cavitation model. The numerical investigation of cavitating flow of marine propeller E779A was carried out with different advance ratios and cavitation numbers to verify the numerical simulation method. Tip clearance effects on the performance of pumpjet propulsor had been investigated. Results showed that the structure and characteristics of the tip leakage vortex and the efficiency of the propulsor dropped more sharply with the increase of the tip clearance size. Furthermore, the numerical simulation of tip clearance cavitation of pumpjet propulsor had been presented with different rotational speed and tip clearance size. The mechanism of tip clearance cavitation causing a further loss of the efficiency had been studied. The influence of rotational speed and tip clearance size on tip clearance cavitation had been investigated.

• 한국전산유체공학회지
• /
• 제18권1호
• /
• pp.7-12
• /
• 2013

This paper presents a numerical investigation of the influences of various non-uniform tip clearances on the performance and flow field in a centrifugal compressor. Numerical simulations were conducted for three centrifugal compressor impellers in which the tip clearance height varied linearly from the leading edge to the trailing edge. The numerical result was compared with the experimental data for validation. Although the performance improved for low tip clearances, a smaller tip clearance at the trailing edge reduced the overall tip leakage flow more effectively than a smaller tip clearance at the leading edge. Therefore, a smaller tip clearance at the trailing edge lowered the mixing loss caused by interactions between the tip leakage flow and the main passage flow.

• 설비공학논문집
• /
• 제13권2호
• /
• pp.134-143
• /
• 2001

This paper presents the characteristics of flank and tip seal leakage in a scroll compressor for air-conditioners with R-22 under actual operating conditions. It is well known that the leakage has significant effect on the performance of the scroll compressor. Experiments were performed by using indirect method for measuring mass flow rate passing through flank and tip seal under actual operating conditions, In addition, an analytical model for tip seal leakage was developed to investigate tangential and radial leakage observed at grooves and contact points of tip seals. For low oil concentration, theoretical results were compared with experimental data to verify the analytical model. As a result, leakages through flank and tip seal parts were evaluated as afunction of pressure ratio, orbiting angle, discharge pressure, tip clearance, and leakage point. It was also found that the tip seal leakage was considerable even though the tip seal provided adequate sealing effect.

• 한국추진공학회지
• /
• 제14권6호
• /
• pp.60-68
• /
• 2010

본 연구에서는 팁 형상이 가스터빈 블레이드의 팁 열전달에 미치는 영향을 알아보기 위하여 선형 캐스케이드의 블레이드에 설치된 평면 팁, 스퀼러 팁, Groove 팁들에 대하여 열전달 계수가 측정되었다. 블레이드 팁에서의 열전달 계수는 색상검출방식에 기반을 둔 천이액정법을 이용하여 측정되었으며 각각의 팁 형상에 대하여 팁 간극은 블레이드 스팬의 1.5%와 2.3% 두 조건에서 실험을 수행하였다. 캐스케이드 출구 속도와 블레이드 코드길이에 기초를 둔 Reynolds 수는 $2.48{\times}10^5$ 이다. Groove 팁 표면에서의 열전달 계수는 평면 팁보다 낮게 측정되었으며, 특히 흡입면을 따라 경사진 홈이 파인 팁에서는 스퀼러 팁보다 낮은 열전달 계수가 측정되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.311-318
• /
• 2010

본 연구에서는 팁 형상이 가스터빈 블레이드의 팁 열전달에 미치는 영향을 알아보기 위하여 선형 캐스케이드의 블레이드에 설치된 평면 팁, 스퀼러 팁, Groove 팁들에 대하여 열전달 계수가 측정되었다. 블레이드 팁에서의 열전달 계수는 색상검출방식에 기반을 둔 천이액정법을 이용하여 측정되었으며 각각의 팁 형상에 대하여 팁 간극은 블레이드 스팬의 1.5%와 2.3%로 변경 하에 실험을 수행하였다. 캐스케이드 출구 속도와 블레이드 코드길이에 기초를 둔 Reynolds 수는 $2.48{\times}10^5$ 이다. Groove 팁 표면에서의 열전달 계수는 평면 팁보다 낮게 측정되었으며, 특히 흡입면을 따라 경사진 홈이 파인 팁에서는 스퀼러 팁보다 낮은 열전달 계수가 측정되었다.

• Journal of Plant Biotechnology
• /
• 제37권4호
• /
• pp.517-528
• /
• 2010

종자 발달과 발아는 수분과 양분 함량의 급격한 변화를 수반하는 복합적인 과정이다. 본 연구에서는 유전자 발현과 단백질 구조 비교 분석을 통해 벼 종자의 발아와 발달과정에 관여하는 액포막 aquaporin (tonoplast intrinsic protein)을 규명하였다. OsTIP3;1, OsTIP3;2는 종자 특이적인 TIP로 종자가 성숙되는 시기에 발현되었다가, 종자가 발아하면서 전사체가 사라지는 양상을 보였으며, ABA 처리에 의해 발현이 유도되었다. 단백질 구조 예측 결과로부터 OsTIP3;1, OsTIP3;2가 단백질의 N-말단, B와 E loop에 다른 TIP와 뚜렷이 구분되는 인산화 잔기 특징을 확인하였다. OsTIP2;1과 OsTIP4;3은 종자가 발달하는 과정에서 유전자 발현이 감소하였다가, 종자 발아 후기에 뿌리와 배축의 신장이 활발한 시기에 발현이 급증하였다. 특히 OsTIP2;1은 뿌리에서 강한 발현을 보였으므로, 뿌리 생장에 필요한 팽압 공급에 중요한 기능을 할 것으로 제안된다. OsTIP2;1과 OsTIP4;3 단백질의 N-말단에는 특징적으로 메틸화 (methylation) 가능성이 높은 아미노산 잔기가 예측되었다. OsTIP2;2는 OsTIP2;1과는 달리 종자 침윤 후 7시간 이내에 발현이 빠르게 유도되며, 발아가 억제되는 조건에서도 유전자 발현이 유지되는 것으로 보아 종자의 초기 수화 과정에 관여할 것으로 추측된다. OsTIP2;2 단백질의 N-말단에는 OsTIP2;1에 존재하는 인산화 Ser 잔기와 메틸화 잔기가 결실된 특징을 보였다. 이런 결과들은 벼 종자의 발달과 발아 과정에서 나타나는 액포의 종류와 기능에 따라 서로 다른 TIP가 선택적으로 유전자 발현수준에서 조절되며, 인산화, 메틸화 등 단백질 수식에 의한 활성조절 기작 역시 매우 다르다는 것을 시사한다.

• Archives of Plastic Surgery
• /
• 제41권1호
• /
• pp.3-11
• /
• 2014

Background This study aimed at overcoming the disadvantages of septal extension grafts and keeping the nasal tip as natural as possible by using different forms of the graft and additional supporting methods depending on the case. Methods Among 458 patients who received a septal extension graft from March 2008 to September 2011, 107 patients were selected who underwent at least a 6-month follow-up. Patients were categorized according to the primary objective of the operation; an upturned tip correction or tip lengthening, tip lengthening with tip projection, or retracted columella correction. Each group of patients received a different type of septal extension graft out of 3 different types of grafts based on the purpose of the operation. The evaluation of the results was made from by comparing preoperative and postoperative photographs of the tip angle, projection, and nasolabial angle. Results The average tip angle for the patients in the upturned tip correction group was reduced to 98.3 from 124.9 degrees. For the patients in the tip lengthening with tip projection group, the average tip angle was reduced to 96.8 from 122.4 degrees and the average tip projection was increased to 27.5 from 23.2 mm. The average nasolabial angle for the patients in the retracted columella correction group was increased to 94.6 from 74.8 degrees. Conclusions Sufficient nasal tip lengthening and projection could be achieved by applying a septal extension graft using the graft best suited for the group of patients categorized by surgical objective.

• 대한전자공학회논문지TE
• /
• 제42권1호
• /
• pp.61-68
• /
• 2005

영상 기반 엔더링은 장면을 3차원 기하 모델로 구축할 필요없이 실사 영상만을 이용하여 빠른 속도로 사실감 높은 결과 영상을 렌더링 할 수 있는 기법이다. 특히, '그림 속으로의 여행(Tour into the Picture: TIP)' 기법은 3차원 배경을 매우 간단히 구축할 수 있어 널리 이용되고 있다. 그러나 기존 TIP 기법은 영상 촬영 지점을 많이 벗어나면 원거리 지형 정보 부족으로 인해 시점 이동 범위에 한계가 있다. 이점을 보완하기 위해 본 연구에서는 다수의 TIP 영상을 합성하여 넓은 가상환경을 구축하는 방법을 개발하였다. 제안된 방법은 먼저, 다수의 시점에서 각각 TIP 모델을 구축하고, TIP 모델을 구성하는 전경 물체와 배경 물체를 각각 보간하여 렌더링 함으로써 부드러운 네비게이션 영상을 얻었다. 본 연구는 게임, 차량용 네비게이션 등 다양한 산업 분야에 응용될 수 있다.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.33-39
• /
• 2001

The welding quality by Gas Tungsten Arc Welding shows very high level, but the welding speed is lower than that of gas metal arc welding. Also, the welding quality by automatic GTAW is variable as the arc characteristics is changed by the consumption of electrode tip. The purpose of this study is to investigate the relation between the properties of tungsten electrode tip and the various arc characteristics at high current region. In this study, the high welding current 200A was applied to the repeated arc start test and long term arcing test using the $\phi$3.2 tungsten electrodes with cone angle 30$^{\circ}$, 45$^{\circ}$, 60$^{\circ}$sharp tip, and 60$^{\circ}$surface polished (S.P.) sharp tip. It was confirmed that the maximum arc pressure by the initial electrode condition was highest in 45$^{\circ}$sharp tip, and the next in 60$^{\circ}$sharp tip, the last was in 30$^{\circ}$sharp tip and 60$^{\circ}$S.P.. But, the maximum arc pressure after the repeated arc start test and long term arcing test was decreased considerably. But, the maximum arc pressure was highest also in 45$^{\circ}$ sharp tip after the tests, the next was in 30$^{\circ}$sharp tip, and the last was in 60$^{\circ}$sharp tip and 60$^{\circ}$S.P.. The arc start characteristics was the most excellent in 60$^{\circ}$S.P., By long term arcing test, the lanthania included in tungsten electrode was extinguished at tip surface preferentially, therefore the arc characteristics of electrode tip got worse.

• Journal of Forest and Environmental Science
• /
• 제38권4호
• /
• pp.239-248
• /
• 2022

Forestry crane work in a forest harvester or forwarder is regarded as one of most hard work requiring a very high level of operation skill. The operator must handle two or more multi-axes joysticks simultaneously to control the multiple manipulators for maneuvering the crane-tip to its intended location. This study has been carried out to develop a crane-tip controller which can intuitively maneuver the crane-tip, resulting in improving the productivity by decreasing the technical difficulty of control as well as reducing the workload. The crane-tip controller consists of a single 2-axis joystick and a control algorithm run on microcontroller. Lab-scale forestry crane was constructed using electric cylinders. The crane-tip control algorithm has the crane-tip follow the waypoints generated on the given path considering the dead band region using LBO (Lateral Boundary Offset). A speed control gain to change the speed of relevant cylinders relatively is applied as well. By the P (Proportional) control within the control interval of 20 msec, the average error of crane-tip control on the predefined straight path turned out to be 14.5 mm in all directions. When the joystick is used the waypoints are generated in real time by the direction signal from the joystick. In this case, the average error of path control was 12.4 mm for straight up, straight forward and straight down movements successively at a certain constant speed setting. In the slant movement of crane-tip by controlling two axes of joystick simultaneously, the movement of crane-tip was controlled in the average error of 15.9 mm when the crane-tip is moved up and down while moving toward forward direction. It concluded that the crane-tip control was possible using the control algorithm developed in this study.