• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.487-495
• /
• 2005

Mechanical properties of in-service facilities are required to evaluate the integrity of power plants and chemical plants. Non-destructive technique can be used to evaluate the mechanical properties. To investigate the mechanical properties using ultrasonic technique, the four classes of thermally aged specimens were prepared using an artificially accelerated aging method. Ultrasonic tests, tensile tests, fracture toughness tests, and hardness tests were performed for the specimens. Then the mechanical properties were compared with ultrasonic parameters such as attenuation and non-linear parameter. From the investigation, we confirm that the ultrasonic parameter can be used to evaluate the mechanical properties.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.111-113
• /
• 2007

The Mechanical properties of steel in hot strip mill were associated with the alloy composition, plastic deformation, cooling history and so on. In the case of the same alloy composition and deformation conditions, cooling history on ROT (run out table) is the main factor in affecting mechanical properties of steel, especially, in carbon steel. On ROT, the steel undergoes under various kinds of cooling conditions such as radiation, convection by air, water and wetting zone. The coiling temperature (CT) of the steel is also important factor in affecting mechanical properties. But with the same CT, the mechanical properties of steel can be different because the temperature history of cooling is more important factor than CT itself. In this study, we have studied the relations between temperature history and mechanical properties of steel and then the predicted mechanical properties have compared with the measured values.

• Journal of Biosystems Engineering
• /
• 제24권3호
• /
• pp.243-252
• /
• 1999

The damage caused in the processes and distributions after harvesting the fruits and vegetables is attributed to the mechanical factors such as compressive and impact forces. Compression tests of biological materials provide an objective method for determining the apparent modulus of elasticity and mechanical properties which are significant in quality evaluation and control, and them maximum allowable compressive forces for minimizing mechanical damage. This study was performed to determine the mechanical properties of apple and pear, and to investigate effect of specimen shapes on the mechanical properties of them. A computer program was developed for measuring the mechanical properties and analyzing the data obtained from the measurement. Compression tests on the sample were performed with then replications at each treatment and at 25 mm/min loading rate. Mechanical properties of the apple was generally shown the higher value than those of the pear, and it was though that data obtained form the cylindrical specimen removed from the sample was more reliable than from the specimen cut in half.

• 한국주조공학회지
• /
• 제32권5호
• /
• pp.225-230
• /
• 2012

In this study, a more practical and simulation approach which can predict the mechanical properties of aluminum alloys is proposed. First, cooling rate, micro-structure, and mechanical properties of casting product were measured through casting experiment. The relation between cooling rate and SDAS decrease exponentially and the linearly decreasing relation exist between SDAS and mechanical properties. Then, the cooling rate was calculated by casting process simulation and the mechanical properties were predicted by using the relations that were derived through experiment. Experimentally measured mechanical properties and predicted values by simulation were in the range of relatively small difference. The mechanical properties of various Al alloys are expected to be predicted by the casting process simulation before actual casting.

• Geomechanics and Engineering
• /
• 제15권1호
• /
• pp.631-643
• /
• 2018

The estimation of the strength and other mechanical parameters characterizing the tensile behavior of granites can play an important role in civil engineering tasks such as design, construction, rehabilitation and repair of existing structures. The purpose of this paper is to apply data mining techniques, such as multiple regression (MR), artificial neural networks (ANN) and support vector machines (SVM) to estimate the mechanical properties of granites. In a first phase, the mechanical parameters defining the complete tensile behavior are estimated based on the tensile strength. In a second phase, the estimation of the mechanical properties is carried out from different combination of the physical properties (ultrasonic pulse velocity, porosity and density). It was observed that the estimation of the mechanical properties can be optimized by combining different physical properties. Besides, it was seen that artificial neural networks and support vector machines performed better than multiple regression model.

• 한국의류학회지
• /
• 제8권2호
• /
• pp.47-57
• /
• 1984

Effect on the hand value and mechanical properties of blend ratio and weight had been investigated Oil summer suits for men. Relation between the mechanical properties and the deformation in behavior was also studied. The mechanical properties which influence the hand values and total hand value had been discussed and the relation between mechanical properties, hand values and fabric count had, too. As result, the following conclusions had been obtained. 1) The values of tensile properties increased with the increase of blend ratio of wool. The values of surface properties increased according to the increase of blend ratio of polyester. 2HB(bending properties) of polyester/wool blend showed higher value than that of $100\%$ wool, but there was no change in the shearing properties according to the blend ratio. The values of stiffness, crispness and anti-drape stiffness of blend fabric showed higher values than those of $100\%$ wool fabric. The value of fullness (including softness) of blend fabric showed lower value than that of $100\%$ wool fabric. 2) The correlation between hand values and mechanical properties showed following order. in stiffness : bending properties>surface properties in crispness: surface properties>bending properties in anti-drape stiffness: bending properties>surface properties>shearing properties.

• Journal of Magnetics
• /
• 제4권2호
• /
• pp.52-54
• /
• 1999

Injection molding is one of the methods to prepare dielectromagnets-permanent magnets made from hard magnetic powder (or from mixture of powders) bonded by dielectric materials. Magnetic properties of dielectromagnets are worse than those of sintered magnets made from the same hard magnetic powders, but this type of the permanent magnet has many advantages. One of them is simpler technology-easier in comparison to the technology of sintered magnets. The injection molded dielectromagnets do not need any final treatment. This technology permits to control magnetic, thermal and mechanical properties of dielectromagnets. The main chracteristics of dielectormagnets are magnetic properties, however mechanical properties have serious influence onto a range of their applications. The main factors shaping mechanical properties have serious influence onto a range of their applications. The main factors shaping mechanical properties of dielectromagnets are the kind and quantity of resin and the technology. The purpose of this investigateion was to find the correlation between infection conditions and the mechanical properties of dielectromagnets. Influence of two parameters of injection, temperature and pressure on mechanical and magnetic properties of dielectromagnets were not significantly changed. Increasing of pressure of injection also does not influence on mechanical properties of analysed samples, however increasing of temperature of injection significantly improved both compression and bending strength.

• 대한가정학회지
• /
• 제39권11호
• /
• pp.223-232
• /
• 2001

This study, by explaining the relationship between mechanical properties and clothing formability, aims to propose functional data for tailoring performance of fabrics of good tailorability. The KES-FB system was used to measure factors of mechanical properties and also the technique of stepwise-block-regression method was applied to investigate relationship between functional properties and mechanical properties of men's shirks. As results of vasual inspection of men's shirts, it showed that good fabrics had higher value in the LT, bending properties, shear properties and RC than poor fabrics in Total Appearance Value(TAV). And finally, A formula was obtained for calculating the VIA of men's shirts from functional properties which were calculated from the mechanical properties.

• Computers and Concrete
• /
• 제18권1호
• /
• pp.113-137
• /
• 2016

Extensive experimental studies on remarkable mechanical properties Polypropylene Fibre Reinforced Self-compacting Concrete (PFRSCC) have been executed, including different fibre volume fractions of Polypropylene fibers (0.25%, 0.5%, 0.75%, and 1%) and different water to cement ratios (0.21, 0.34, 0.38, and 0.41). The experimental program was carried out by using two hundred and sixteen specimens to obtain the impact resistance and mechanical properties of PFRSCC materials, considering compressive strength, splitting tensile strength, and flexural strength. Statistical and analytical studies have been mainly focused on experimental data to correlate of mechanical properties of PFRSCC materials. Statistical results revealed that compressive, splitting tensile, and flexural strengths as well as impact resistance follow the normal distribution. Moreover, to correlate mechanical properties based on acquired test results, linear and nonlinear equations were developed among mechanical properties and impact resistance of PFRSCC materials.

• 한국표면공학회지
• /
• 제48권3호
• /
• pp.100-104
• /
• 2015

The nickel alloys gets a great deal of attention due to their good mechanical, chemical and magnetic properties. Especially Ni-P alloy systems are very attractive due to their good corrosion resistance and the wear resistance in important technological applications. In this study, the effects of phosphorus acid concentration in plating solution on composition of Ni-P alloy coatings were studied. The Ni-P electrodeposits of the various P contents were investigated in order to understand effect of the composition on mechanical properties of Ni-P electrodeposits. The mechanical properties of electrodeposits increased as the P content in electrodeposits increase. The results of mechanical properties were explained by grain size and P solid solution effect. The effects of heat treatment on mechanical properties of Ni-P alloy coatings were also studied.