• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.423-432
• /
• 1999

This paper proposes a 12­pulse diode rectifier system with low kVA components suitable for powering switch mode power supplies or ac/dc converter applications. The proposed 12-pulse system employs a polyphase transformer, a zero sequence blocking transformer (ZSBT) in the dc link, and an interphase transformer. Results produce near equal leakage inductance in series with each diode rectifier bridge ensuring equal current sharing and performance improvements, The utility input currents and the voltage across the ZSBT are analyzed the kVA rating of each component in the proposed system is computed. The 5th , 7th , 17th and 19th harmonics are eliminated in the input line currents resulting in clean input power. The dc link voltage magnitude generated by the proposed rectifier system is nearly identical to a conventional to a conventional 6-pulse system. The proposed system is suitable to retrofit applications as well as in new PWM drive systems. Simulation and experimental results from a 208V , 10kVA system are shown.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.12 no.4 s.27
• /
• pp.301-306
• /
• 2006

In order to estimate the characteristics of water movements around artificial upwelling structure, current measurements were carried out along lines E-W and S-N on May 4th(neap tide} and May 30th(spring tide), 2006. In the study area, southeastward flow was dominant during the field observations, and the pattern of water movement in the upper layer above 30m depth was different from that in the lower layer below 30m depth Vertical flow(w-component} around the artificial structure area and western area was shown to be upward flow, but downward flow occurred in the southern, northern and eastern parts at the neap tide. At the spring tide, the ebb current along E-W line showed upwelling flow in the eastern part and western area and showed upwelling flow near the artificial structure area and downwelling flow far away that one. At the spring tide, upward flow was dominant along S-N line during the flood current Volume transport by upward flow was higher than that by downward flow. Volume transport by upward flow during ebb of neap tide was greater than during flood current of neap tide, but was reverse at the spring tide.

• Restorative Dentistry and Endodontics
• /
• v.38 no.4
• /
• pp.204-209
• /
• 2013

Objectives: The objective of this in vitro study was to evaluate and compare the cytotoxicity of four different root canal sealers i.e. Apexit Plus (Ivoclar Vivadent), Endomethasone N (Septodont), AH-26 (Dentsply) and Pulpdent Root Canal Sealer (Pulpdent), on a mouse fibroblast cell line (L929). Materials and Methods: Thirty two discs for each sealer (5 mm in diameter and 2 mm in height) were fabricated in Teflon mould. The sealer extraction was made in cell culture medium (Dulbecco's Modified Eagle's Medium, DMEM) using the ratio 1.25 $cm^2/mL$ between the surface of the sealer samples and the volume of medium in a shaker incubator. Extraction of each sealer was obtained at 24 hr, 7th day, 14th day, and one month of interval. These extracts were incubated with L929 cell line and 3-(4,5-dimethylthiazol-2yl)-2,5-diphenyltetrazolium bromide (MTT) assay was done. Two-way ANOVA for interaction effects between sealer and time and Post-hoc multiple comparison using Tukey's test across all the 16 different groups were used for statistical analysis. Results: Apexit Plus root canal sealer was significantly less toxic than other sealers (p < 0.05) and showed higher cellular growth than control. Endomethasone N showed mild cytotoxicity. AH-26 showed severe toxicity which became mild after one month while Pulpdent Root Canal Sealer showed severe to moderate toxicity. Conclusions: Apexit Plus was relatively biocompatible sealer as compared to other three sealers which were cytotoxic at their initial stages, however, they became biocompatible with time.

• Animal Bioscience
• /
• v.35 no.8
• /
• pp.1223-1234
• /
• 2022

Objective: The objectives of this study were to evaluate the effects of daily feed intake during the laying period on embryonic myogenic differentiation 1 (MYOD1), myogenic factor 5 (MYF5), and myogenic factor 6 (MYF6) gene expression in genetically fat and lean lines of chickens. Methods: An experiment in a 2×2 factorial design was conducted with two dietary intake levels (100% and 75% of nutrition recommendation) and two broiler chicken lines (fat and lean). Two lines of hens (n = 384 for each line) at 23th week of age were randomly divided into 4 treatments with 12 replicates of 16 birds. The experiment started at 27th week of age (5% egg rate) and ended at 54th week of age. Hatched eggs from the medium laying period were collected. Real time polymerase chain reaction analysis was used to analyse the MYOD1, MYF5, and MYF6 mRNA levels of E7, E9, E11, E13, and E15 body tissues and E17, E19, and E21 chest and thigh muscle samples. Results: The results indicated that there were significant effects of line, dietary intake, and interactions between them on MYOD1, MYF5, and MYF6 gene mRNA expression levels in embryonic tissues. Low daily feed intake did not change the expression trend of MYOD1 mRNA in either line, but changed the peak values, especially in lean line. Low daily feed intake altered the trend in MYF5 mRNA expression level in both lines and apparently delayed its onset. There was no apparent effect of low daily feed intake on the trends of MYF6 mRNA expression levels in either line, but it significantly changed the values on many embryonic days. Conclusion: Maternal nutrient restriction affects myogenesis and is manifested in the expression of embryonic MYOD1, MYF5, and MYF6 genes. Long term selection for fat deposition in broiler chickens changes the pattern and intensity of myogenesis.

• Economic and Environmental Geology
• /
• v.16 no.1
• /
• pp.11-18
• /
• 1983

Gyeongsang Basin in the southeastern part of the Korean peninsular is characterized by many fault systems. To decipher the geotectonical evolution of the Korean peninsular and marginal basins in her adjacent areas it is prerequisite to understand the spatial distribution pattern and mutual relationships of these fault systems. Because of difficulties in finding any criterion to recognize the faults in field, their extension and mutual relationships in ages are not very clear yet. As an attempt to find geophysical criteria to recognize the fault, geoelectrical resistivity survey was carried out in this study. With the Wenner configuration four resistivity soundings and twenty seven resistivity profilings were done. The electrode distance used was up to 50m. From the results of the resistivity soundings and boring data of earlier groundwater investigations the depth of alluvial and weathered zone was established to be at most 20m in the study area. In the resistivity profiling low resistivity anomaly zones are detected on every traverse, which are interpreted as caused by fractures, fault clays and mylonites in the fault zone. The width of the fault zone amounts to 0.3-1km. By correlating and connecting the negative anomaly zones from traverse to traverse one can determine the trend of th of the faultzone and therefore that of fault itself. The recognized fault trend in this way was $N15^{\circ}-20^{\circ}E$ and this coincides with the direction of the inferred fault line from earlier geological surface mapping. With the help of this characteristical negative anomaly the existance of another $N80^{\circ}W$ trending fault was estabished. This study has shown that geoelectrical resistivity survey can be applied successfully to the problem of tracing fault line insofar as a fault zone has been developed along fault line.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.2
• /
• pp.117-123
• /
• 2004

A 30 nm $In_{0.7}GaAs$ High Electron Mobility Transistor (HEMT) with triple-gate has been successfully fabricated using the $SiO_2/SiN_x$ sidewall process and BCB planarization. The sidewall gate process was used to obtain finer lines, and the width of the initial line could be lessened to half by this process. To fill the Schottky metal effectively to a narrow gate line after applying the developed sidewall process, the sputtered tungsten (W) metal was utilized instead of conventional e-beam evaporated metal. To reduce the parasitic capacitance through dielectric layers and the gate metal resistance ($R_g$), the etchedback BCB with a low dielectric constant was used as the supporting layer of a wide gate head, which also offered extremely low Rg of 1.7 Ohm for a total gate width ($W_g$) of 2x100m. The fabricated 30nm $In_{0.7}GaAs$ HEMTs showed $V_{th}$of -0.4V, $G_{m,max}$ of 1.7S/mm, and $f_T$ of 421GHz. These results indicate that InGaAs nano-HEMT with excellent device performance could be successfully fabricated through a reproducible and damage-free sidewall process without the aid of state-of-the-art lithography equipment. We also believe that the developed process will be directly applicable to the fabrication of deep sub-50nm InGaAs HEMTs if the initial line length can be reduced to below 50nm order.

• The Journal of the Petrological Society of Korea
• /
• v.10 no.3
• /
• pp.179-189
• /
• 2001

The determination of trace concentration of U, Th and Pb was carried out for chemical dating of zircon and monazite by electron microprobe. Detection limit and error range should be considered to measure characteristic X-rays of M-line from those minerals, which are low in the ionization of atom and low peak intensity in the spectrum. The element of U, Th and Pb were simultaneously measured with 3 spectrometers equipped with PET crystal to reduce a total counting time and error due to drift of instrumental operating condition. Detection limit could be improved from increase of the peak/background ratio through adjusting pulse height analyzer about 1000 mv baseline. Under permissible maximum analytical conditions, theoretical detection limit of U, Th and Pb is down to 30 ppm (99% confidence level). The analytical result was maintained at a relative error $\pm$10% ($2{\sigma}$) in 800 ppm Pb, $\pm$5% ($2{\sigma}$) in 2330 ppm U and $\pm$10% ($2{\sigma}$) in dating from a single measurement of zircon at 15 keV and 100 nA. However, for the precise dating of zircon and monazite, if it is considered a 3 $\mu\textrm{m}$ spatial resolution, <100 ppm ($3{\sigma}$) detection limit and <$\pm$10% ($2{\sigma}$) relative error, optimum analytical conditions are given as 15~20 keV accelerating voltage, 100~200 nA beam current and 300~1200 sec total counting time. To reduce material damage by high current, there is need to be up to 3~5 $\mu\textrm{m}$ of electron beam diameter, or to use arithmetic average of multiple measuring at a shorter counting time. A younger or relatively low concentration rocks can be dated chemically by lower detection limit and improved precision resulted from increase of current and measuring time.

• Journal of Korean Academy of Nursing
• /
• v.37 no.3
• /
• pp.391-400
• /
• 2007

Purpose: The purpose of this study was to identify the nursing images appearing in elementary school textbooks. Method: This study targeted 130 textbooks of 13 subjects under the 7th national curriculum for elementary schools as of December 2005. Nursing-related texts, photographs, and illustrations in the textbooks were analyzed by using a content analysis method. As for the textbook analysis, two coders thoroughly read the textbooks to record nursing-related content per coding paper, respectively. Result: The total number of nursing-related content appearing in 130 textbooks of 13 subjects was 70. More nursing-related content was exhibited in the photograph and illustration domain(N=57, 81.4%) than in the text domain(N=13, 18.6%). Nursing-related content(N=70) appeared in the order of nursing activities with 56(80.0%), nursing as a job with 10(14.3%), and others with 4(5.7%). As for the nursing image of nursing-related content, positive images weremost with 30(42.9%), followed by negative images with 21(30.0%), and neutral images with 19(27.1%). Conclusion: Nursing-related content was dealt with too little, and dependent nursing activities such as medication, and assisting roles for doctor's examinations and treatments mainly appeared. Also, the main activity place was a hospital. To introduce proper and adequate nursing activities to the students, various types of nursing-related data and material should be distributed to front line schools, teachers, main authors, and publishing companies.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.86-94
• /
• 2000

This study was performed to investigate types and formation mechanism of cracks in two Al alloy welds, A5083 and A7N01 spot-welded by pulse Nd : YAG laser, using SEM, EPMA and Micro-XRD. In the weld zone, three types of crack were observed : center line crack({TEX}$C_{C}${/TEX}), diagonal crack({TEX}$C_{D}${/TEX}), and U shape crack({TEX}$C_{U}${/TEX}). Also, HAZ crack({TEX}$C_{H}${/TEX}) was observed in the HAZ region, furthermore, mixing crack({TEX}$C_{M}${/TEX}) consisting of diagonal crack and HAZ crack was observed. White film was formed at th hot crack region in the fractured surface after it was immersed to 10% NaOH water. In the case of A5083 alloy, white films in {TEX}$C_{C}${/TEX} crack and {TEX}$C_{D}${/TEX} crack region were composed of low melting phases, {TEX}$Fe_{2}SiAl_{8}${/TEX} and eutectic phases, $Mg_2$Al$_3$ and $Mg_2$Si. Such films observed $CuAl_2$, {TEX}$Mg_{32}(Al,Zn)_{3}${/TEX}, MgZn$_2$, $Al_2$CuMg and $Mg_2$Si were observed in the whitely etched films near {TEX}$C_{C}${/TEX} crack and {TEX}$C_{D}${/TEX} crack regions. The formation of liquid films was due to the segregation of Mg, Si, Fe in the case of A5083 alloy and Zn, Mg, Cu, Sim in the case of A7N01 alloy, respectively. The {TEX}$C_{C}${/TEX} and {TEX}$C_{D}${/TEX} cracks were regarded as a result of the occurrence of tensile strain during the welding process. The formation of {TEX}$C_{M}${/TEX} crack is likely to be due to the presence of liquid film at the grain boundary near the fusion line in the base metal as well as in the weld fusion zone during solidification. The {TEX}$C_{U}${/TEX} crack is considered a result of the collapsed keyhole through incomplete closure during rapid solidification.

• Journal of Korean Elementary Science Education
• /
• v.26 no.4
• /
• pp.440-448
• /
• 2007

The purpose of this study is to examine elementary students' conceptions of magnetic fields around various magnets by drawing tasks. A total of 105 elementary students from the 3rd and 6th grade levels were asked to draw how iron filings would arrange around magnets. We classified their drawings of magnetic field lines with some criteria to identify conceptions of magnetic forces and checked them through interviewing about their representative drawing. Through analyzing drawings, we discovered that 40% of elementary students drew the correct arrangement of iron filings around a bar magnet. In the case of two bar magnets in opposite directions, 33% of them drew correct patterns of iron dust and around two magnets in the same direction only 20% did well. Only 2.9% and 7.6% of students presented the correct drawings of magnetic fields near a disc and a horseshoe magnet. While 3rd grade students were supposed to be poor in drawings of magnetic fields around a loose and a dense coil which was not learned about, only 31% and 23% of 6th grade students who have just studied electromagnetism properly drew patterns of iron dust. This shows that only one quarter of students understood the magnetic filed lines even after instruction of electromagnetism. Many of 6th grade students learned a solenoid becomes just as a permanent magnet, but very few of them correctly drew a magnetic field line could distinguish between the iron dust around a loose and dense coil. After interviewing students, it is found that students consider magnetic forces to be existed only in parts of magnet because many of them drew magnetic field line of a specific areas around magnets. Students had misconceptions that magnetic forces exist only on the poles not in the middle around a horseshoe magnet. Also the disc-shape magnet made students to reveal various types of misconceptions: N- and S-poles are mixed in a whole magnet and right part of a disc-shape magnet is N-pole, left part is S-pole. Students who had not studied magnetic fields of around a magnet and electromagnets could not draw the correct patterns of iron dust suggest that it is indispensable for students to teach how patterns of iron filings would represent a visual image of magnetic fields in order to understand magnetic fields.