• 한국재료학회지
• /
• 제12권4호
• /
• pp.283-289
• /
• 2002

The E.M.F of the galvanic cell with fused salt was measured to determine the activities of zinc at 700-820K over the entire composition range of liquid Zn-Cd alloys. The cell used was as follows: (-) W ｜ Zn(pure) $Zn^{2+}(KCI-LiCl)$ ｜ Zn(in Zn-Cd alloy) ｜ W (+) The activities of zinc in the alloys showed positive deviation from Raoult's law over the entire composition range. The activity of cadmium and some thermodynamic functions such as Gibbs free energy, enthalpy, entropy were derived from the results by the thermodynamic relationship. The comparison of the results and the literature data was made. The liquid Zn-Cd alloy is found to be close to the regular solution. The concentration fluctuations in long wavelength limit, $S_{cc}(o)$, in the liquid alloy was calculated from the results.

• Corrosion Science and Technology
• /
• 제23권4호
• /
• pp.283-288
• /
• 2024

Hot-dip Zn-Mg-Al coatings have a complex microstructure consisting of Zn, Al, and MgZn₂ phases. Its crystal structure depends on alloy content and cooling rates. Microstructure and corrosion resistance of these coatings might be affected by heat treatment. To investigate effect of heat treatment on microstructure and corrosion resistance of Zn-Mg-Al coatings, Zn-1.5%Mg-1.5%Al coated steel was heated up to 550 ℃ at a heating rate of 80 ℃/s and cooled down to room temperature. At above 500 ℃, the ternary phase of Zn-MgZn₂-Al was melted down. Only Zn and MgZn₂ phases remained in the coating. Heat- and non-heat-treated specimens showed similar corrosion resistance in Salt Spray Test (SST). When a Zn-3.0%Mg-2.5%Al coated steel was subjected to heat treatment at 100 ℃ or 300 ℃ for 200 h and compared with GA and GI coated steels, the microstructure of coatings was not significantly changed at 100 ℃. However, at 300 ℃, most Al in the coating reacted with Fe in the substrate, forming a Fe-Al compound layer in the lower part of the coating. MgZn₂ was preferentially formed in the upper part of the coating. As a result of SST, Zn-Mg-Al coated steels showed excellent corrosion resistance, better than GA and GI.

• 해양환경안전학회지
• /
• 제20권5호
• /
• pp.504-510
• /
• 2014

본 연구에서는 2014년 03월에 인천 H항의 5개 정점(S1~S5)에서 채취된 표층 퇴적물의 물리화학적 특성을 조사하고, COD, AVS, IL 및 중금속(Cd, Cu, Ni, Pb, Zn, Cr, Hg)을 분석하여 오염도를 평가하였다. 입도분석, 비표면적분석, XRD 및 XRF 분석을 통하여 채취된 퇴적물 시료 모두 거의 동일한 산화물과 광물로 구성되었음을 확인하였다. 국내기준으로 COD, AVS 및 IL 세 항목의 총점에 대한 오염도는 S2, S3, S5 지점은 2등급으로 S1, S4 지점은 3등급으로 평가되었다. 중금속 오염의 경우 Cd, Ni, Pb은 USEPA 기준으로 중간오염에 해당하였고, Cu, Zn 및 Cr은 심한오염으로 분류되었다. 농집지수를 이용한 오염도 평가결과 Cd가 Class 3으로 평가되었고, 농축계수를 이용한 평가결과 모든 지점에서 Cd, Pb, Zn의 경우 1보다 큰 것으로 나타났다. 또한 총농축계수는 S4지점이 3.1로 가장 높은 것으로 나타났다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.575-578
• /
• 2004

The charging tendency of $Zn_2SiO_4:Mn^{2+}$ phosphor surface was modified in order to improve discharging characteristic of green cell in an ac-plasma display panel (ac-PDP). The Zinc-silicate ($Zn_2SiO_4:Mn^{2+}$) green-emitting phosphor was coated with magnesium oxide(MgO), which is viable to have positive charge on the surface. After fabricating the green cell with MgO-coated $Zn_2SiO_4:Mn^{2+}$, the electrical and optical properties in the cell were examined. It was found that the dynamic voltage margin could be increased while the address time was reduced. It may be ascribed to the change of charging tendency of $Zn_2SiO_4:Mn^{2+}$ phosphor by MgO coating, which makes it possible to stable wall-charge accumulation. When $Zn_2SiO_4:Mn^{2+}$ phosphor was coated with 1.3wt%-MgO, the address time was reduced 1.2 ${\mu}s$ and the address voltage lowered 25 V without any misfiring problem, compared to those of typical $Zn_2SiO_4:Mn^{2+}$ phosphor layer. The luminescence intensity of green cell using MgO-coated phosphor layer was also improved by 10%.

• 한국재료학회지
• /
• 제20권1호
• /
• pp.31-36
• /
• 2010

Methylene blue (MB) was degraded by $TiO_2$ and ZnO deposited on an activated carbon fiber (ACF) surface under UV light. The ACF/$TiO_2$ and ACF/ZnO composites were characterized by BET, SEM, XRD, and EDX. The BET surface area was related to the adsorption capacity for composites. The SEM results showed that titanium dioxide and zinc oxide are distributed on the ACF surface. The XRD results showed that the ACF/$TiO_2$ and ACF/ZnO composites contained a unique anatase structure for $TiO_2$ and a typical hexagonal phase for ZnO respectively. These EDX spectra showed the presence of peaks of Ti element on ACF/$TiO_2$ composite and peaks of Zn element on the ACF/ZnO composite. The blank experiments for either illuminating the MB solution or the suspension containing ACF/$TiO_2$ or ACF/ZnO in the dark showed that both illumination and the catalyst were necessary for the mineralization of organic dye. Additionally, the ACF/$TiO_2$ composites proved to be efficient photocatalysts due to degradation of MB at higher reaction rates. The addition of an oxidant $([NH_4]_2S_2O_8)$ led to an increase of the degradation rate of MB for ACF/$TiO_2$ and ACF/ZnO composites.

• 한국결정성장학회지
• /
• 제28권5호
• /
• pp.222-227
• /
• 2018

$Zn_{1-x}Co_x$ Zeolitic Imidazolate Framework-8(ZIF)(x = 0~0.05)를 2-methylimidazole을 사용하여 $Zn^{2+}$와 $Co^{2+}$를 공침시켜 합성하고, 이를 $600^{\circ}C$에서 2시간 열처리하여 순수한 ZnO 나노입자와 Co가 도핑된 ZnO 나노입자를 합성했다. x가 < 0.05일 경우, 2-methylimidazole 링커가 $Zn^{2+}$ 및 $Co^{2+}$ 모두에 강하게 배향되어 균질한 Zn/Co ZIFs가 합성되었으며, 열처리를 통해 Co가 균일하게 도핑된 ZnO를 합성할 수 있었다. 반면, $x{\geq}0.05$일 때는 불균질한 Zn/Co ZIFs가 합성되었으며, 열처리 이후 $Co_3O_4$ 이차상이 형성되었다. 합성된 나노입자들에 대한 가스감응특성 평가 결과, 3 at%의 Co가 도핑된 ZnO 센서는 순수한 ZnO와는 달리 trimethylamine에 대해 고감도, 고선택적 가스감응특성을 나타냈다. 본 연구의 bimetallic ZIF 유도 산화물 나노복합체 합성방법은 고성능 가스센서를 설계하는데 활용될 수 있을 것으로 기대된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 제4회 영호남학술대회 논문집
• /
• pp.25-30
• /
• 2002

The ternary semiconducting compounds of the $A_{4}BX_{6}$(A=Cd, Zn, Hg; B=Si, Sn, Ge; X=S, Se, Te) type exhibit strong fluorescence and high photosensitivity in the visible and near infrared ranges, so these are supposed to be materials applicable to photoelectrical devices. These materials were synthesized and single crystals were first grown by Nitsche, who identified the crystal structure of the single crystals. In this paper. author describe the undoped and $Co^{2+}$-doped $Zn_{4}SnSe_{6}$ single crystals were grown by the chemical transport reaction(CTR) method using iodine of $6mg/cm^{3}$ as a transport agent. For the crystal. growth, the temperature gradient of the CTR furnace was kep at $700^{\circ}C$ for the source aone and at $820^{\circ}C$ for the growth zone for 7-days. It was found from the analysis of x-ray diffraction that undoped and $Co^{2+}$-doped $Zn_{4}SnSe_{6}$ compounds have a monoclinic structure. The optical absorption spectra obtained near the fundamental absorption edge showed that these compounds have a direct energy gaps. These temperature dependence of the optical energy gap were closely investigated over the temperature range 10[K]~300[K]

• Current Photovoltaic Research
• /
• 제5권1호
• /
• pp.20-24
• /
• 2017

Recently, three-dimensional (3D) light harvesting structures are highly attracted because of their high light harvesting capacity and charge collection efficiencies. In this study, we have fabricated $Cu_2ZnSn(S_xSe_{1-x})_4$ based 3D thin film solar cells on PR patterned Molybdenum (Mo) substrates using photolithography technique. Specifically, Mo patterns were deposited on PR patterned Mo substrates by sputtering and the thin Cu-Zn-Sn stacked layer was deposited over this Mo patterns by sputtering technique. The stacked Zn-Sn-Cu precursor thin films were sulfo-selenized to form CZTSSe pattern. Finally, CZTSSe absorbers were coated with thin CdS layer using chemical bath deposition and ZnO window layer was deposited over CZTSSe/CdS using DC sputtering technique. Fabricated 3-D solar cells were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF) analysis, Field-emission scanning electron microscopy (FE-SEM) to study their structural, compositional and morphological properties, respectively. The 3% efficiency is achieved for this kind of solar cell. Further efforts will be carried out to improve the performance of solar cell through various optimizations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.141-141
• /
• 2010

ZnS:Mn yellow phosphors doped with Cu for white light emitting diodes were synthesized by solid state reaction method. Photoluminescence excitation spectra originated from $Mn^{2+}$ were ranged from 450 nm to 500 nm. The yellow emission at around 580 nm was associated with $^4T_1{\rightarrow}^6A_1$ transition of $Mn^{2+}$ ions in ZnS:Mn,Cu phosphors. The highest photoluminescence intensity of the phosphors under 405 nm excitation was obtained at Cu concentration of 0.02 mol%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.461.1-461.1
• /
• 2014

본 연구진에서는 기존에 Ag2S 양자점을 흡광층으로 활용하여 양자점 감응형 태양전지(QDSC)를 제작, 그 성능과 특징을 분석하여 발표한 바 있다. 기존 연구에서 제작된 Ag2S QDSC는 11 mA/cm2의 비교적 높은 광전류와 260 mV의 비교적 낮은 전압으로 인해 1.2%의 광전환효율 성능을 나타내는 것으로 보고되었다. 추후 연구로 진행된 본 결과에서는, 기존에 Single absorber로 사용된 Ag2S의 한계를 보완하기 위해 CdS를 도입하여 co-sensitization을 활용하였다. CdS는 약 2.3 eV의 밴드갭 에너지를 갖는 물질로, 1.1 eV의 밴드갭을 갖는 Ag2S에 비해 흡광 영역은 좁지만 그만큼 전자-정공 재결합을 억제할 수 있는 장점을 가지고 있다. 또한, 전도층으로 사용한 n-type 물질인 ZnO 나노선과의 밴드구조가 매우 적합하게 조화되어, ZnO/CdS/Ag2S 순서로 이종구조를 접합시켰을 때 세 물질의 Conduction band level과 Valence band level이 순차적으로 연결되는 cascade-shaped 밴드구조를 이루게 된다. 빛을 받아 Ag2S와 CdS에서 생성된 전자는 이 cascade 모양의 conduction band를 따라 순차적으로 ZnO로 잘 전달되게 되어, 효율 향상에 큰 도움을 주었다. 이런 장점들로 인해, CdS-Ag2S co-sensitized QDSC는 Ag2S QDSC에 비해 2배나 향상된 효율인 2.4%를 기록하였으며, 이는 IPCE spectrum 측정 등으로 근거가 뒷받침되었다.