• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제16권7호
• /
• pp.604-610
• /
• 2003

The effects of sintering additives such as B $i_2$ $O_3$ and $V_2$ $O_{5}$ on the microwave dielectric and sintering properties of (Z $n_1$$_{-xM}$ $g_{x}$)Ti $O_3$ system were investigated. Highly dense samples were obtained for (Z $n_{0.8}$M $g_{0.2}$)Ti $O_3$ at the sintering temperature range of 870~90$0^{\circ}C$ with B $i_2$ $O_3$ and $V_2$ $O_{5}$ additions of 〈1 wt.%, respectively. The microwave dielectric properties of (Z $n_{0.8}$M $g_{0.2}$)Ti $O_3$ with 0.45 wt.%B $i_2$ $O_3$ and 0.55 wt.% $V_2$ $O_{5}$ sintered at 90$0^{\circ}C$ were as follows : Q$\times$ $f_{o}$ = 50,800 GHz, $\varepsilon$$_{r}$ = 22, and $\tau$$_{f}$ = -53 ppm/$^{\circ}C$. In order to improve temperature coefficient of resonant frequency, Ti $O_2$ was added to the above system. The optimum amount of Ti $O_2$ was 15 moi.% when sintered at 87$0^{\circ}C$, at which we could obtain following results: Q$\times$ $f_{o}$ = 32,800 GHz, $\varepsilon$$_{r}$ = 26, and$\tau$$_{f}$ = 0 ppm/$^{\circ}C$.EX>.EX>.EX>.EX>.EX>.EX>.EX>.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• 제25권4호
• /
• pp.135-139
• /
• 2015

$Bi_2Te_3-Bi_2Se_3$ alloy which is typical n-type thermoelectric material were grown by traveling heater method (THM) technique. We investigate the effect of the composition of $100-x(Bi_2Te_3)-x(Bi_2Se_3)$ and doping of n-type dopants such as $SbI_3$ and $CdCl_2$. Maximum figure of merit of $Bi_2Te_3-Bi_2Se_3$ alloy was observed with $CdCl_2$ 0.1 wt% (Z: $2.73{\times}10^{-3}/K$) and $SbI_3$ 0.05 wt% (Z: $2.29{\times}10^{-3}/K$). Deviation along the length of $Bi_2Te_3-Bi_2Se_3$ ingot grown by THM method is low, which indicates that the ingot is very homogenized. Also we observed the close relationship of between anisotropy ratio and dopant in the $90(Bi_2Te_3)-10(Bi_2Se_3)$ alloys. And we confirmed the fact that anisotropy ratio exerts thermoelectric performance in $Bi_2Te_3$ based n-type thermoelectric material.

• East Asian mathematical journal
• /
• 제14권2호
• /
• pp.269-279
• /
• 1998

For a codimension 1 submanifold in a Euclidean 2n-space, the degree of the gauss map mod 2 is the semi-characteristic of the manifold in $Z_2$ coefficient.

• The Journal of Korean Society for Radiation Therapy
• /
• 제26권1호
• /
• pp.43-50
• /
• 2014

In case of all patients who receive radiation therapy, a treatment plan is established and all steps of treatment are planned in the same geometrical condition. In case of head and neck cancer patients who undergo simulated treatment through computed tomography (CT), patients are fixed onto a table for planning, but laid on the top of the treatment table in the radiation therapy room. This study excogitated and fabricated an adjustable holder for head and neck cancer patients to fix patient's position and geometrical discrepancies when performing radiation therapy on head and neck cancer patients, and compared the error before and after adjusting the position of patients due to difference in weight to evaluate the correlation between patients' weight and range of error. Computed tomography system(High Advantage, GE, USA) is used for phantom to maintain the supine position to acquire the images of the therapy site for IMRT. IMRT 4MV X-rays was used by applying the LINAC(21EX, Varian, U.S.A). Treatment planning system (Pinnacle, ver. 9.1h, Philips, Madison, USA) was used. The setup accuracy was compared with each measurement was repeated five times for each weight (0, 15, and 30Kg) and CBCT was performed 30 times to find the mean and standard deviation of errors before and after the adjustment of each weight. SPSS ver.19.0(SPSS Inc., Chicago, IL,USA) statistics program was used to perform the Wilcoxon Rank test for significance evaluation and the Spearman analysis was used as the tool to analyze the significance evaluation of the correlation of weight. As a result of measuring the error values from CBCT before and after adjusting the position due to the weight difference, X,Y,Z axis was $0.4{\pm}0.8mm$, $0.8{\pm}0.4mm$, 0 for 0Kg before the adjustment. In 15Kg CBCT before and after adjusting the position due to the weight difference, X,Y,Z axis was $0.2{\pm}0.8mm$, $1.2{\pm}0.4mm$, $2.0{\pm}0.4mm$. After adjusting position was X,Y,Z axis was $0.2{\pm}0.4mm$, $0.4{\pm}0.5mm$, $0.4{\pm}0.5mm$. In 30Kg CBCT before and after adjusting the position due to the weight difference, X,Y,Z axis was $0.8{\pm}0.4mm$, $2.4{\pm}0.5mm$, $4.4{\pm}0.8mm$. After adjusting position was X,Y,Z axis was $0.6{\pm}0.5mm$, $1.0{\pm}0mm$, $0.6{\pm}0.5mm$. When the holder for the head and neck cancer was used to adjust the ab.0ove error value, the error values from CBCT were $0.2{\pm}0.8mm$ for the X axis, $0.40{\pm}0.54mm$ for Y axis, and 0 for Z axis. As a result of statistically analyzing each value before and after the adjustment the value was significant with p<0.034 at the Z axis with 15Kg of weight and with p<0.038 and p<0.041 at the Y and Z axes respectively with 30Kg of weight. There was a significant difference with p<0.008 when the analysis was performed through Kruscal-Wallis in terms of the difference in the adjusted values of the three weight groups. As it could reduce the errors, patients' reproduction could be improved for more precise and accurate radiation therapy. Development of an adjustable device for head and neck cancer patients is significant because it improves the reproduction of existing equipment by reducing the errors in patients' position.

• Asian-Australasian Journal of Animal Sciences
• /
• 제21권5호
• /
• pp.723-731
• /
• 2008

Immunomodulatory feed additives might offer alternatives to antimicrobial growth promoters in pig production. This experiment was designed to determine the effects of dietary galacto-mannan-oligosaccharide (GMOS) and chitosan oligosaccharide (COS) supplementation on the immune response in early-weaned piglets. Forty 15-day-old piglets (Duroc$\times$Landrace$\times$Yorkshire) with an average live body weight of $5.6{\pm}0.51kg$ were weaned and randomly assigned to 4 treatment groups that were fed maize-soybean meal diets containing either basal, 110 mg/kg of lincomycin, 250 mg/kg of COS or 0.2% GMOS, respectively, over a 2-week period. Another six piglets of the same age were sacrificed on the same day at the beginning of the study for sampling, in order to obtain baseline values. Interleukin (IL)-1${\beta}$gene expression in peripheral blood monocytes, jejunal mucosa and lymph nodes, as well as serum levels of IL-1${\beta}$ IL-2 and IL-6, IgA, IgG, and IgM, were evaluated for 5 pigs from each group at 15 and 28 days of age. The results indicate that weaning stress resulted in decreases in serum antibody and cytokine levels. Dietary supplementation with GMOS or COS enhanced (p<0.05) IL-1${\beta}$gene expression in jejunal mucosa and lymph nodes, as well as serum levels of IL-1${\beta}$ IL-2, IL-6, IgA, IgG and IgM compared to supplementation with lincomycin. These findings suggest that GMOS or COS may enhance the cell-mediated immune response in early-weaned piglets by modulating the production of cytokines and antibodies, which shows that GMOS or COS have different effects than the antibiotic on animal growth and health.

• Journal of Food Hygiene and Safety
• /
• 제14권4호
• /
• pp.339-345
• /
• 1999

The present study was performed to investigate photodegradation rate constants and degradation products of dichlorvos and methidathion by the USEPA method. The two pesticides were very stable in sunlight for 16 days from September 2 to 18, 1998 and humic acid had no sensitizing effect on the photolysis of each pesticide in sunlight. The photolysis rate was fast-est for methidathion, followed by dichlorvos in the presence of UV irradiation. Photodegradation rate constant and half-life of dichlorvos were 0.0208 and 33.3 min, respectively. Photodegradation rate constant and half-life of methidathion were 0.6789 and 1.0min, respectively. The two pesticides were degraded completely in the presence of UV irradiation and UV irradiation with TiO$_2$in about 3 hours. Therefore, it is suggested that UV treatment will be effective for the degradation of pesticides in the process of drinking water purification. In case of dichlorvos and methidathion, UV irradiation with TiO$_2$was more effective for degradation than W irradiation. In order to identify photolysis products, the extracts of degradation products were analyzed by GC/ MS. The mass spectrum of photolysis products of dichlorvos was at m/z 153, those of the photolysis of methidathion were at m/z 198 and 214, respectively. Photolysis products of dichlorvos was Ο, Ο-dimethyl phosphate(DMP), those of methidathion were Ο, Ο-dimethyl phosphorothioate(DMTP) and Ο, Ο-dimethyl phosphorodithioate (DMDTP).

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.17-40
• /
• 2000

Resin cements are used for cementing indirect esthetic restorations such as resin or porcelain inlays. Because of its limitations in curing of purely light cured resin cements due to attenuation of the curing light by intervening materials, dual cured resin cements are recommended for cementing restorations. The physical properties of resin cements are greatly influenced by the extent to which a resin cures and the degree of cure is an important factor in the success of the inlay. The purpose of this study was to evaluate the influence of porcelain thickness and exposure time on the polymerization of resin cements by measuring the microhardness and the degree of conversion, to investigate the nature of the correlation between two methods mentioned above, and to determine the exposure time needed to harden resin cements through various thickness of porcelain. The degree of resin cure was evaluated by the measurements of microhardness [Vickers Hardness Number(VHN)] and degree of conversion(DC), as determined by Fourier Transform Infrared Spectroscopy(FTIR) on one light cured composite resin [Z-100(Z)] and three dual cured resin cements [Duo cement(D), 3M Resin cement(R), and Dual cement(DA)] which were cured under porcelain discs thickness of 0mm, 1mm, 2mm, 3mm with light exposure time of 40sec, 80sec, 120sec, and regression analysis was performed to determine the correlation between VHN and DC. In addition, to determine the exposure time needed to harden resin cements under various thickness of porcelain discs, the changes of the intensity of light attenuated by 1mm, 2mm, and 3mm thickness of porcelain discs were measured using the curing radiometer. The results were obtained as follows ; 1. The values of microhardness and the degree of conversion of resin cements without intervening porcelain discs were 31~109VHN and 51~63%, respectively. In the microhardness Z was the highest, followed by R, D, DA. In the degree of conversion, D and DA was significantly greater than Z and R(p<0.05). 2. The microhardness and the degree of conversion of the resin cements decreased with increasing thickness of porcelain discs, and increased with increasing exposure time, D and R showed great variation with inlay thickness and exposure time, whereas, DA showed a little variation. 3. The intensity of light through 1mm, 2mm, and 3mm porcelain inlays decreased by 0.43, 0.25, and 0.14 times compared to direct illumination, and the respective needed exposure times are 53 sec, 70 sec, and 93 sec. In D and R, 40 sec of light irradiation through 2mm porcelain disc and 80 sec of light irradiation through 3mm porcelain disc were not enough to complete curing. 4. The microhardness and the degree of conversion of the resin cements showed a positive correlationship(R=0.791~0.965) in the order of R, D, Z, DA. As the thickness of porcelain discs increased, the decreasing pattern of microhardness was different from that of the degree of conversion, however.

• Journal of Trauma and Injury
• /
• 제32권1호
• /
• pp.1-7
• /
• 2019

Purpose: The present study aimed to evaluate the influence of how the trauma care system applied on the management of trauma patient within the region. Methods: We divided the patients in a pre-trauma system group and a post-trauma system group according to the time when we began to apply the trauma care system in the Halla Hospital after designation of a trauma center. We compared annual general characteristics, injury severity score, the average numbers of the major trauma patients, clinical outcomes of the emergency department, and mortality rates between the two groups. Results: No significant differences were found in the annual patients' average age ($54.1{\pm}20.0$ vs. $52.8{\pm}18.2$, p=0.201), transportation pathways (p=0.462), injury mechanism (p=0.486), injury severity score (22.93 vs. 23.96, p=0.877), emergency room (ER) stay in minutes (199.17 vs. 194.29, p=0.935), time to operation or procedure in minutes (154.07 vs. 142.1, p=0.767), time interval to intensive care unit (ICU) in minutes (219.54 vs. 237.13, p=0.662). The W score and Z score indicated better outcomes in post-trauma system group than in pre-trauma system group (W scores, 2.186 vs. 2.027; Z scores, 2.189 vs. 1.928). However, when analyzing survival rates for each department, in the neurosurgery department, in comparison with W score and Z score, both W score were positive and Z core was higher than +1.96. (pre-trauma group: 3.426, 2.335 vs. post-trauma group: 4.17, 1.967). In other than the neurosurgery department, W score was positive after selection, but Z score was less than +1.96, which is not a meaningful outcome of treatment (pre-trauma group: -0.358, -0.271 vs. post-trauma group: 1.071, 0.958). Conclusions: There were significant increases in patient numbers and improvement in survival rate after the introduction of the trauma system. However, there were no remarkable change in ER stay, time to ICU admission, time interval to emergent procedure or operation, and survival rates except neurosurgery. To achieve meaningful survival rates and the result of the rise of the trauma index, we will need to secure sufficient manpower, including specialists in various surgical area as well as rapid establishment of the trauma center.

• Journal of the Korean Chemical Society
• /
• 제34권6호
• /
• pp.517-526
• /
• 1990

The crystal structures of two alditol acetates, D-glucitol hexaacetate and xylitol pentaacetate, have been determined by diffraction methods with Mo-K$\alpha$radiation, using direct methods for phase determinations. The crystal data are: for D-glucitol hexaacetate, P2$_1$, with a = 10.275 (2), b = 8.363 (1), c = 12.560 (5) $\AA;\beta$ = 95.97 $(2)^{\circ}$, Z = 2; for xylitol pentaacetate, P2$_1$/C with a = 18.126 (1), b = 11.422 (2), c = 8.649 (1) $\AA$, $\beta = 95.03 (1)^{\circ}$, Z = 4. Both molecules have extended zigzag carbon chain conformations which differ from previous studies of the structures of D-glucitol and xylitol and also differ from NMR studies on alditol acetates. The bond lengths and angles are normal, with mean values over both structures of C($sp^3)-C(sp^3): 1.514 (10),\; C(sp^3)-O: 1.444 (6),\; C(sp^2)-O: 1.347 (9),\; C(sp^2)=O: 1.197 (6),\; C(sp^2)-C(sp^3): 1.479(9){\AA},\; C(sp^3)-C(sp^3)-C(sp^3): 114.6 (17),\; O-C(sp^3)-C(sp^3): 109.4 (23),\; C(sp^2)-O-C(sp^3): 117.4 (6),\; O=C(sp^2)-O: 122.6 (6),\; C(sp^3)-C(sp^2)-O: 111.8 (7),\; C(sp^3)-C(sp^2)=O: 125.5 (4)^{\circ}$. The atoms of acetate groups are in coplanar. There are no particularly short intermolecular contacts and the molecules are held together by van der Waals force only.

• Bulletin of the Korean Chemical Society
• /
• 제31권3호
• /
• pp.645-649
• /
• 2010

An efficient synthetic method of Z-selective 3-ethoxycarbonyl-2-halo-1,3-dienes and 3-vinyl-2-halo-1,3-dienes was developed from the reaction of allenols having ethoxycarbonyl and vinyl group with indium trihalides at room temperature in $CH_2Cl_2$.