• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1771-1776
• /
• 2011

In this paper, as an attempt to improve the preparation conditions of $YBa_2Cu_3Ox$ superconducting bulk samples, the properties of $YBa_2Cu_3Ox$ superconductor depending on the particle size of YBCO powder and $BaPbO_3$ as an additive have been investigated, and a study on the effects of additive to the density, grain alignment, and porosity of samples that affect the critical current of superconductor has been performed. In order to prepare superconductor, $YBa_2Cu_3Ox$ powder synthesized by sol-gel method, showing a size distribution of 0.2~1 ${\mu}m$ was used. The $BaPbO_3$ added to promote grain growth and to decrease porosities and weak links between grain boundaries of $YBa_2Cu_3Ox$ superconductors. In the samples prepared by sol-gel synthesized powder with 10, 20, and 30 wt% conductive $BaPbO_3$ additives, the sample with 20 wt% $BaPbO_3$ obtained the highest critical current of 4.74 A, showing 20 wt% higher critical current than that with solid state synthesized powder.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.55-58
• /
• 2003

[ $YBa_2Cu_3Ox$ ](YBCO) oxide superconductor was prepared by sol-gel method to improve its superconducting properties, and it was made to be a fine powder, which has the same property of solid state reacted powder. $BaPbO_3$ was synthesized with $BaCO_3$, BaO, PbO, and $PbO_2$ and analyzed by XRD. YBCO superconductor was prepared by use of sol-gelled YBCO powder and additive $BaPbO_3$ and its critical temperature and transition temperature were shown as 91.9 K, 3.7 K respectively in case 20 wt.% $BaPbO_3$ was added to pure sol-gelled YBCO powder.

• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1483-1490
• /
• 1994

YBa2Cu3Ox-Ag(YBCO-Ag) thick films were fabricated on the zirconia substrate by a screen printing method. The starting powder was a mixture of YBCO, prepared by a coprecipitation in oxalic acid, and Ag2O. The influence of heat treatment conditions on properties of thick films was investigated. It was observed that Jc of thick films was directly proportional to the orientation factor of thick films and the optimimum preparation condition was the heat treatment of thick films at 100$0^{\circ}C$ for 3 min in O2. The improvement of Jc by the addition of Ag was considered as a result of the suppression of microcracks in the films.

• Journal of the Korean Ceramic Society
• /
• v.30 no.12
• /
• pp.1007-1014
• /
• 1993

YBa2Cu3Ox(YBCO) thick films were prepared by a screen printing of the powders, obtained by a coprecipitation in oxalic acid, on the Y2O3-stabilized zirconia substrates and their superconducting properties were determined. TC, JC and the orientation factor of the thick films increased with increasing temperature up to 103$0^{\circ}C$ and then the superconducting properties disappeared with further heat treatments. The optimization of JC was achieved by heating thick films at 103$0^{\circ}C$ for 7min. In this case the TC of the thick film was determined to be 87.5K. It was observed that TC of thick films depends on the orthorhombicity and JC is likely governed by a microstructure of YBCO rather than by the orientation factor.

• Journal of the Korean Vacuum Society
• /
• v.3 no.1
• /
• pp.117-121
• /
• 1994

SrTiO3(100) 단결정을 3keV 아르곤이온으로 에칭하면 표면원소의 산화 상태가 환원되고 표면의 거칠기가 증가하는 것이 XPS와 SEM으로 측정되었다. 그러나 3keV의 산소이온으로 에칭하면 표면원소 의 화학적 상태도 변하지 않고 표면도 평탄한 상태로 계속 유지된다. 산소 이온에 의하여 에칭된 SrTiO3 기판상에 off-axis rf 스퍼트링 방법으로 성장된 YBa2Cu3Ox 박막이 아르곤 이온에 의하여 에칭 된 SrTiO3 기판상에 성장된 YBa2Cu3Ox 박막보다 높은 Tc,zero and Jc를 보여주었다. 이논문은 YBCO초전 도 박막의 성장과 전자공학적 활용을 위한 리토그라피 공정에서 이온밀링 공정의 조건은 매우 주의하여 선택되어야 함을 보여준다.