• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.369.1-369.1
• /
• 2014

Au-functionalized $WO_3$ nanotubes were synthesized using ZnO nanowire templates. Transmission electron microscopy revealed the Au nanoparticles on the outer surface of a typical $WO_3$ nanotube ranged from 5 to 25 nm. The multiple networked Au-functionalized $WO_3$ nanotube sensors showed responses of 820-3, 924% in the $NO_2$ concentration range of 1-5 ppm at $300^{\circ}C$. These responses were approximately 5-12 fold higher than those observed for pristine $WO_3$ nanotube sensors over the same $NO_2$ concentration range. A model describing the gas sensing mechanism of Au-functionalized $WO_3$ nanotubes is discussed.

• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.326-330
• /
• 2015

In this study, we demonstrate the photoelectrochromic devices composed of $TiO_2$ and $WO_3$ nanostructures prepared by anodization method. The morphology and the crystal structure of anodized $TiO_2$ nanotubes and $WO_3$ nanoporous layers are investigated by SEM and XRD. To fabricate a transparent photoelectrode on FTO substrate, a $TiO_2$ nanotube membrane, which has been detached from Ti substrate, is transferred to FTO substrate and annealed at $450^{\circ}C$ for 1 hr. The photoelectrode of $TiO_2$ nanotube and the counter electrode of $WO_3$ nanoporous layer are assembled and the inner space is filled with a liquid electrolyte containing 0.5 M LiI and 5 mM $I_2$ as a redox mediator. The properties of the photoelectrochromic devices is investigated and Pt-$WO_3$ electrode system shows better electrochromic performance compared to $WO_3$ electrode.

• Journal of Hydrogen and New Energy
• /
• v.22 no.5
• /
• pp.656-662
• /
• 2011

The purpose of this study was to correlate between photoelectrochemcial hydrogen production rate and electron transfer with various types of metal doped $TiO_2$ nanotubes as photoanodes. In order to fabricate light sensitized photoanode, CdS, $WO_3$, and Pt were doped by electrodeposition method. As the results of experiments, the electron transfer was favorable from higher position to lower position of conduction band (CB). In consequence, the higher hydrogen production rate was as follows, CdS/$TiO_2$ (100 $umol/hr-cm^2$) > $WO_3/TiO_2$ (20 $umol/hr-cm^2$) > Pt/$TiO_2$ (10 $umol/hr-cm^2$). The surface characterizations exhibited that crystal structure, morphological and electrical properties of various metal depoed $TiO_2$ nanotubes by the results of SEM, TEM, XPS, and photocurrent measurements.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.16.1-16.1
• /
• 2011

Gas sensor properties of $WO_3$ nanowire structures have been studied. The sensing layer was prepared by deposition of tungsten metal on porous single wall carbon nanotubes followed by thermal oxidation. The morphology and crystalline quality of $WO_3$ material was investigated by SEM, TEM, XRD and Raman analysis. A highly porous $WO_3$ nanowire structure with a mean diameter of 82 nm was obtained. Response to CO, $NH_3$ and $H_2$ gases diluted in air were investigated in the temperature range of $100{\sim}340^{\circ}C$ The sensor exhibited low response to CO gas and quite high response to $NH_3$ and $H_2$ gases. The highest sensitivity was observed at $250^{\circ}C$ for $NH_3$ and $300^{\circ}C$ for $H_2$. The effect of the diameters of $WO_3$ nanowires on the sensor performance was also studied. The $WO_3$ nanowires sensor with diameter of 40 nm showed quite high sensitivity, fast response and recovery times to $H_2$ diluted in dry air. The sensitivity as a function of detecting gas concentrations and gas sensing mechanism was discussed. The effect of dilution carrier gases, dry air and nitrogen, was examined.

• Journal of Environmental Science International
• /
• v.27 no.11
• /
• pp.967-974
• /
• 2018

In this study, we evaluated the photocatalytic oxidation efficiency of aromatic volatile hydrocarbons by using $WO_3$-doped $TiO_2$ nanotubes (WTNTs) under visible-light irradiation. One-dimensional WTNTs were synthesized by ultrasonic-assisted hydrothermal method and impregnation. XRD analysis revealed successful incorporation of $WO_3$ into $TiO_2$ nanotube (TNT) structures. UV-Vis spectra exhibited that the synthesized WTNT samples can be activated under visible light irradiation. FE-SEM and TEM images showed the one-dimensional structure of the prepared TNTs and WTNTs. The photocatalytic oxidation efficiencies of toluene, ethylbenzene, and o-xylene were higher using WTNT samples than undoped TNT. These results were explained based on the charge separation ability, adsorption capability, and light absorption of the sample photocatalysts. Among the different light sources, light-emitting-diodes (LEDs) are more highly energy-efficient than 8-W daylight used for the photocatalytic oxidation of toluene, ethylbenzene, and o-xylene, though the photocatalytic oxidation efficiency is higher for 8-W daylight.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.25.2-25.2
• /
• 2011

The tungsten oxide wire-like nanostructure is fabricated by deposition and thermal oxidation of tungsten metal on porous single wall carbon nanotubes (SWNTs). The morphology and crystalline quality of materials are investigated by SEM, TEM, XRD and Raman analysis. The results prove that $WO_3$ wire-like nanostructure fabricated on SWNTs show highly porous structures. Exposure of the sensors to NH3 gas in the temperature range of 150~300$^{\circ}C$ resulted in the highest sensitivity at $250^{\circ}C$ with quite rapid response and recovery time. Response time as a function of test concentrations and NH3 gas sensing mechanism is reported and discussed.