• 대한환경공학회지
• /
• 제38권6호
• /
• pp.291-298
• /
• 2016

불용성 전극은 전기화학 공정에 있어 가장 핵심적인 소재이며, 이를 이용한 전기화학적 수처리 공정은 난분해성 물질을 제거하는 유용한 방법으로서 이에 대한 연구가 지속적으로 이루어져 오고 있다. 전기화학적 수처리 공정은 주로 산화전극에서의 산화반응과 환원전극에서의 환원반응을 이용하는 것이다. 본 연구에서는 불용성 전극의 제조공정에서 전처리 방법이 전극의 수명에 미치는 영향을 평가하였다. 실험결과 촉매전극층을 코팅하는 물질계 및 코팅방법을 동일하게 하는 경우에도 기판의 전처리 방법 즉, 기판표면의 조도, 세정방법, 중간층 형성 여부 및 방법 등에 따라 전극의 수명이 크게 달라지는 것을 확인하였다. 실험은 가장 많이 사용되는 전극의 하나인 $IrO_2/Ti$ 전극을 대상으로 하였다. 샌드 블라스팅 공정의 경우 입도를 달리하는 샌딩 미디어를 이용하여 전극을 제조하고 이에 대한 수명을 평가한 결과 #80알루미나(입도 $212{\sim}180{\mu}m$)를 이용하는 경우가 가장 효과적인 것으로 나타났다. 기판에 대한 세정 공정은 arc plasma를 이용하는 것이 가장 우수하였으며, 중간층을 형성함에 있어서는 스퍼터링법을 이용하여 Ta 계열의 중간층을 형성하는 방법을 적용하는 것이 가장 바람직한 것으로 확인되었다.

• 한국재료학회지
• /
• 제8권12호
• /
• pp.1165-1169
• /
• 1998

제1세대 니켈계 단결정 초합금인 CMSX 6를 사용하여 셀렉타법으로 진공 정밀주조하여 단결정을 제작하였다. 주형온도 약 150$0^{\circ}C$, 주입온도 약 163$0^{\circ}C$와 용탕 주입 직후 주형을 2.5mm/분 속도로 하강시켜 단결정을 성장시켰다. 단결정 주조조직에서 기지와 공정조직은 ${\gamma}$' 석출물(Ni$_3$(Al, Ti)) 모양과 크기에 따라 각각 모두 두영역으로 구분되었으며, 공정조직의 Ti함랗은 기지보다 높았다. 즉, EPMA 및 CBED 분석 등으로 ${\gamma}$' 석출물을 분석한 결과, 기지내의 ${\gamma}$'은 크기가 0.5~0.7$\mu\textrm{m}$ 이하이며 화학조성상 Ni$_3$Al에 가까웠으며 격자구조도 Ll$_2$를 나타내었다. 반면에 공정조직에 가까울수록 ${\gamma}$' 크기는 1.0$\mu\textrm{m}$보다 컸으며, 모양도 판상형의 거대한 모양으로 바뀌었다. 화학조성 또한 Ni$_3$Ti에 가까웠으며 격자구조도 D $O_{24}$를 나타내었으므로 수지상과 공정조직의 ${\gamma}$' 석출물은 화학조성 및 격자구조가 상이함을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.74-79
• /
• 2009

Titanium and titanium alloy can be reproduced immediately even if oxide films($TiO_2$) break apart in sea water. Therefore, since titanium demonstrates large specific strength and outstanding resistance to stress corrosion cracking, crevice corrosion, pitting and microbiologically influenced corrosion in sea water environment, it has been widely applied to heat exchanger for ships. In particular, with excellent elongation, pure titanium may be deemed as optimal material for production of heat exchanger plate which is used with wrinkles formed for efficient heat exchange. Conventional plate type heat exchanger prevented leakage of liquid through insertion of gasket between plates and mechanical tightening by bolts and nuts, but in high temperature and high pressure environment, gasket deterioration and leakage occur, so heat exchanger for LPG re-liquefaction device etc do not use gasket but weld heat exchanger plate for use. On the other hand, since welded plate cannot be separated, it is important to obtain high quality reliable welds. In addition, for better workability and production performance, lasers that can obtain weldment with large aspect ratio and demonstrate fast welding speed even in atmospheric condition not in vacuum condition are used in producing products. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through quantitative analysis of oxygen and nitrogen and measurement of hardness as fundamental experiment for the evaluation of titanium laser welding, and evaluated the welding performance and mechanical properties of butt welding. This study welded specimens in various conditions by using laser and GTA welding machine to apply edge welding to heat exchanger, and evaluated the mechanical strength through tensile stress test. As a result of tensile test, laser weldment demonstrated tensile strength 4 times higher than GTA welds, and porosity could be controlled by increasing and decreasing slope of laser power at overlap area.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2011년도 임시총회 및 하계학술연구발표회
• /
• pp.7-8
• /
• 2011

Basically, the lattice mismatch between film and substrate can make those BiFeO3(BFO) films distorted with strain structure. BFO phase can be stabilized on LaAlO3(LAO) represents the example of a multiferroic with giant axial ratio. Its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion and related to the rotation of the oxygen octahedra. In this study, we show that phases with a tetragonal-like epitaxial BFO films can indeed be ferroelectric and also can be stabilized via epitaxial growth onto LAO. Recent reports on epitaxial BFO films show that the crystal structure changes from nearly rhombohedral ("R-like") to nearly tetragonal("T-like") at strains exceeding approximately -4.5%, with the "T-like" structure being characterized by a highly enhanced c/a ratio. While both the "R-like" and the "T-like" phases are monoclinic, our detailed x-ray diffraction results reveal asymmetry change from MA and MC type, respectively. By applying additional strain or by modifying the unit cell volume of the film by substituting Ba for Bi, the monoclinic distortion in the "T-like" MC phase is reduced, i.e. the system approaches a true tetragonal symmetry. There are two different M-H loops for $Bi_{1-x}Ba_xFeO_{3-{\delta}}$(BBFO) and BFO films on SrTiO3(STO) & LAO substrates. Along with the ferroelectric characterization, these magnetic data indicate that the BFO phase stabilized on LAO represents the first example of a multiferroic with giant axial ratio. However, there is a significant difference between this phase and other predicted ferroelectrics with a giant axial ratio: its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion. Therefore, in going from bulk to highly-strained films, a phase sequence of rhombohedral(R)-to-monoclinic ["R-like" MA-to-monoclinic, "T-like" MC-to-tetragonal (T)] is observed. This sequence is otherwise seen only near morphotropic phase boundaries in lead-based solid-solution perovskites (i.e. near a compositionally induced phase instability), where it can be controlled by electric field, temperature, or composition. Our results show that this evolution can occur in a lead-free, stoichiometric material and can be induced by stress alone. Those major results are summarized as follows ; 1) Ba-doping increases the unit cell volume, 2) BBFO on LAO can be fully strained up to x=0.08 as a strain limit (Fig. 1), 3) P(E) & M(H) properties can be tuned by the variation of composition, strain, and film thickness.

• 한국물환경학회지
• /
• 제18권3호
• /
• pp.245-251
• /
• 2002

Reactive dyes waste water, a toxic and refractory pollutant, was treated by an electrochemical method using $Ti/IrO_2$ as anode and Stainless Steel 316 as cathode. In this technique, sodium chloride as an electrolyte was added. A number of experiments were run in a batch system. Artificial samples (reactive blue 19, red 195, yellow 145) were used. Operation parameters, such as supporting electrolyte concentration, current density, pH and sample concentration have been investigated for their influences on COD and color removal efficiencies during electrolysis. After 5 and 90 minites of eletrolysis, color was reduced by 51.5% and 98.9% respectively. Under the condition of current density $10A/dm^2$, NaCl concentration 12mg/l and pH 3, 62.9% of $COD_{Cr}$ was removed after electrolysis for 90 minites. The optimum condition of color removal and COD reduction in this work was found to be the following : pH 3, sodium chloride concentration 20g/l, current density $10A/dm^2$. As a result, we confirmed to be effective to color removal and reduction of refractory organic material.

• Journal of Electrical Engineering and Technology
• /
• 제7권6호
• /
• pp.959-964
• /
• 2012

Internal pressure of vacuum interrupter (VI) is one of the most important parameters in VI operation and may increase due to the outgassing from the materials inside VI or gas permeation through metal flange or ceramic vessel. The increase of the pressure above a certain level leads to the failures of switching or insulation. Therefore, an effective pressure check of VI is essential and an analysis of partial discharge (PD) characteristics is an effective monitoring method to identify the degree of the internal pressure of VI. This paper introduces a research work on monitoring the internal pressure of VI by analyzing PDs which were measured using a capacitive PD coupler. The authors have developed cost effective capacitive coupler based on the ceramic material that has an excellent insulation properties and the main component of the capacitive coupler is made by SrTiO3. Detectable internal pressure range and distinguishability of the internal pressure of VI were investigated. From the PD tests results, the internal pressure range, from $10^{-2}$ torr to 500 torr, can be monitored by PD measurements using the capacitive coupler and PD inception voltage (PDIV) follows the Paschen's law. In addition, rise time of PD pulse at 13.2kV decreases with the increase of the internal pressure of VI.

• Transactions on Electrical and Electronic Materials
• /
• 제3권1호
• /
• pp.14-17
• /
• 2002

The effects of substrate temperatures and annealing temperatures on the microstructures and ferroelectric properties of PbZ $r_{0.52}$ $Ti_{0.48}$ $O_3$(PZT) thin fims prepared by pulsed laser deposition (PLD) were investigated. For this purpose, the PZT films were deposited at various substrate temperatures (400~$600^{\circ}C$) with post annealing process in oxygen atmosphere. The single perovskite phase was formed at the deposition temperature of 500 to 55$0^{\circ}C$ without post annealing and the PZT films deposited below 50$0^{\circ}C$ formed the single phase with post annealing at $650^{\circ}C$. The grain size of the films increased and the grain boundary of the films was clearly defined as the substrate temperature increased from 400 to 55$0^{\circ}C$. The remnant polarization (Pr) and the coercive field (Ec) of the films deposited at 55$0^{\circ}C$ and annealed at $650^{\circ}C$ were 34.3 $\mu$C/c $m^2$and 60.2 kV/cm, respectively.y.y.

• 보존과학회지
• /
• 제27권1호
• /
• pp.75-90
• /
• 2011

분청사기는 조선초기에 고려상감청자의 무늬가 간소화 된 상태로 시작되었다. 그 후 200여 년 동안에 다양하고 활달한 문양의 민속공예로 발달하였고, 점점 백자를 닮아가는 방향으로 변해가다가, 임진왜란이후에 생산이 중단되었다. 이 논문에서는 분청의 태토와 유약에 대한 화학조성을 분석하고, 여러 도요지들의 결과들을 서로 비교하였다. 또한 다른 논문들에서 중국의 경우와 비교 관찰된 고려청자와 조선백자들에 대한 결과들과 비교 하였다. 생산도요지와 고고학적인 특성에 의하여 28 그룹으로 나누었으며, 각 각의 그룹에서 셋에서 다섯편의 도편을 분석하고, 그들의 평균값을 비교자료로 사용하였다. 분청태토는 한국청자와 백자와 같이 중국 남쪽의 월주요, 경덕진요에서 사용된 운모-석영계의 도석으로 만들어졌다. 유약은 점토질의 원료에 나무재, 태운 석회석과 곱게 빻은 석회가루를 다양한 비율로 혼합되었다. 분청유약의 특성은 조선백자보다는 고려청자와 고려백자에 더 가깝다. 다만 티타늄산화물의 함량은 조선백자와 같이 낮은데, 그 이유는 글래이즈 스톤으로 알려진 도석계의 점토가 분청유약을 제조 하는데 혼합 되었기 때문으로 추정된다. 이 연구의 체계적인 비교방법과 물질적 특성에 대한 내용들은 현재 빠른 속도로 발굴되고 있는 도요지들에 대해서 적용될 수 있을 것이다.