• 한국재료학회지
• /
• 제2권4호
• /
• pp.248-256
• /
• 1992

본 논문에서는 ATi$O_3$(A=Ca, Sr, Ba) 조성을 갖는 단순 페롭스카이트 구조에서 생성되는 격자결함 구조에 대하여 고찰하였다. 페롭스카이트 구조는 고충전밀도를 갖기 때문에 프렌클 결함은 고려되지 않았다. 쇼트키결함이나, 고유전자결함도 자연적으로 포함된 억셉타 불순물 농도에 비하면 무시할 정도로 적은 양이다. 실제적으로 전기적 특성에 영향을 주는 것은 전하적 결함을 발생하는 aliovalent 불순물이다. 삼성분계이기 때문에 양이온간의 비화학양론이 발생하며 BaTi$O_3$나 SrTi$O_3$에서 수백 ppm이내의 AO나 Ti$O_2$의 용해도가 관찰되나, CaTi$O_3$에서는 상당량의 CaO와 $TiO_2의$ 용해가 가능하다.

• Restorative Dentistry and Endodontics
• /
• 제29권3호
• /
• pp.267-272
• /
• 2004

The purpose of this in vitro study was to evaluate the effect of surface defects and cross-sectional configuration of NiTi rotary files on the fatigue life under cyclic loading. Three NiTi rotary files ($K3^{TM},{\;}ProFile^{\circledR},{\;}and{\;}HERO{\;}642^{\circledR}$) with ＃30/.04 taper were evaluated. Each rotary file was divided into 2 subgroups : control (no surface defects) and experimental group (artificial surface defects), A total of six groups of each 10 were tested. The NiTi rotary files were rotated at 300rpm using the apparatus which simulated curved canal (40 degree of curvature) until they fracture. The number of cycles to fracture was calculated and the fractured surfaces were observed with a scanning electron microscope. The data were analyzed statistically. The results showed that experimental groups with surface defects had lower number of cycles to fracture than control group but there was only a statistical significance between control and experimental group in the $K3^{TM}$ (p<0.05), There was no strong correlation between the cross-sectional configuration area and fracture resistance under experimental conditions. Several of fractured files demonstrated characteristic patterns of brittle fracture consistent with the propagation of pre-existing cracks. This data indicate that surface defects of NiTi rotary files may significantly decrease fatigue life and it may be one possible factor for early fracture of NiTi rotary files in clinical practice.

• 한국재료학회지
• /
• 제2권3호
• /
• pp.207-212
• /
• 1992

과잉의 CaO와 $TiO_2$를 각각 포함한 $CaTiO_3$의 결함구조를 평형상태의 전기전도도를 $85O^{\circ}C$와 $1050^{\circ}C$사이에서 산소분압의 함수로 측정하여 연구하였다. 과잉의 CaO는 A site와 B site에 나누어져서 용해되어 $Ca_{Ti}$"와 Vo", 결함을 생성하였으며, 과잉의 $TiO_2$는 $V_{Ca}$"과 Vo"을 생성했다. 평형상태의 전기전도도는 CaO 용해도 5000ppm과 $TiO_2$ 용해도 2000ppm을 각각 나타냈다. 과잉의 양이온에 의하여 생성된 산소공공은 이온전도를 하여 넓은 영역의 산소 분압에 무관한 전도도 최소값을 보였으며, 반대로 대전된 음이온 결함과 결함쌍은 관찰되지 않았다.온 결함과 결함쌍은 관찰되지 않았다.

• 한국결정학회지
• /
• 제11권4호
• /
• pp.195-199
• /
• 2000

Ceramics based on CaTiO₃-NdAlO₃ solid solutions were synthesized in order to study their dielectric microwave properties. Microstructural analysis was performed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) using different analytical methods such as energy-dispersive X-ray spectroscopy (EDXS). It was observed that the heating conditions during sintering and cooling strongly affect the microstructural development of CaTiO₃-NdAlO₃-based ceramics. Various types and concentrations of structural defects were identified, for example, dislocations, twins and/or antiphase boundaries. all such defects resulted in a degradation of the dielectric microwave properties, in particular the quality factor Q. Dielectric properties of CaTiO₃-NdAlO₃-based ceramics can be improved by an appropriate thermal treatment of ceramics which results in a decrease in the concentrations of the identified microstructural defects.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2003년도 제120회 추계학술대회 제 5차 한ㆍ일 치과보존학회 공동학술대회
• /
• pp.594-594
• /
• 2003

I. Objectives The purpose of this study is to determine if propagation of pre-existing manufacturing defects results in brittle fracture of NiTi rotary files by examining the fracture surface of the instrument by SEM, and to compare the fracture time of NiTi rotary files with different flute designs under cyclic loading. II. Materials and Methods This study examined three groups of rotary NiTi instruments (K3, ProFile, Hero). Of each group, 04 taper, size 30 and 06 taper, size 25 were selected.：120 in total. Surface defects were created by simulating the machining process of NiTi rotaries.(omitted)

• 소성∙가공
• /
• 제16권3호
• /
• pp.172-177
• /
• 2007

The process design for large-scale ring rolling of Ti-6Al-4V alloy was performed by calculation method, processing map approach and FEM simulation. The ring rolling design includes geometry design and optimization of process variables. The calculation method was used to make geometry design such as initial billet and blank sizes, and final rolled ring shape. A commercial FEM code, SHAPE-RR was used to simulate the effect of process variables in ring rolling on the distribution of the internal state variables such as strain, strain rate and temperature. In order to predict the forming defects during ring rolling and the formation of over-heating above $\beta$-transus temperature due to deformation heating, the process-map approach based on Ziegler's instability criterion was used with FEM simulation. Finally, an optimum process design to obtain sound Ti-6Al-4V rings without forming defects was suggested through combined approach of Ziegler's instability map and FEM simulation results.

• Journal of Periodontal and Implant Science
• /
• 제53권4호
• /
• pp.295-305
• /
• 2023

Purpose: Various methods have been proposed to achieve the nearly complete decontamination of the surface of implants affected by peri-implantitis. We investigated the in vitro debridement efficiency of multiple decontamination methods (Gracey curettes [GC], glycine air-polishing [G-Air], erythritol air-polishing [E-Air] and titanium brushes [TiB]) using a novel spectrophotometric ink-model in 3 different bone defect settings (30°, 60°, and 90°). Methods: Forty-five dental implants were stained with indelible ink and mounted in resin models, which simulated standardised peri-implantitis defects with different bone defect angulations (30°, 60°, and 90°). After each run of instrumentation, the implants were removed from the resin model, and the ink was dissolved in ethanol (97%). A spectrophotometric analysis was performed to detect colour remnants in order to measure the cumulative uncleaned surface area of the implants. Scanning electron microscopy images were taken to assess micromorphological surface changes. Results: Generally, the 60° bone defects were the easiest to debride, and the 30° defects were the most difficult (ink absorption peak: 0.26±0.04 for 60° defects; 0.32±0.06 for 30° defects; 0.27±0.04 for 90° defects). The most effective debridement method was TiB, independently of the bone defect type (TiB vs. GC: P<0.0001; TiB vs. G-Air: P=0.0017; TiB vs. GE-Air: P=0.0007). GE-Air appeared to be the least efficient method for biofilm debridement. Conclusions: T-brushes seem to be a promising decontamination method compared to the other techniques, whereas G-Air was less aggressive on the implant surface. The use of a spectrophotometric model was shown to be a novel but promising assessment method for in vitro ink studies.

• 자연과학논문집
• /
• 제13권1호
• /
• pp.51-63
• /
• 2003

$1-10^{-20}$atm의 산소 압력과 700K 및 1200K의 등온상태에서 Donor를 첨가한 $BaTiO_3$의 전기전도도를 조사하여 결함의 형태를 조사하였다. Donor를 첨가한 $BaTiO_3$에서 Donor의 첨가량이 증가함에 따라 최소 전기도도를 나타내는 극소점의 위치가 순수한 경우에 비아여 어느 정도 이동이 있었다. 이러한 극소점 위치의 이동으로 불순물의 상대적 함유량을 비교할 수 있었다. 매우 낮은 산소압력에서는 Dopant의 양에 무관하게 전도도 값이 일정하였으며 이러한 현상은 환원반응이 주된 원인임을 알았다.

• Bulletin of the Korean Chemical Society
• /
• 제32권8호
• /
• pp.2531-2536
• /
• 2011

Ethanol is a prototype molecule used in probing catalytic reactivity of oxide catalysts such as $TiO_2$. In the present study, we adsorbed ethanol on $TiO_2$(001) at room temperature (RT) and the corresponding bonding state of ethanol was systematically studied by x-ray photoemission spectroscopy (XPS) using synchrotron radiation. Especially, we compared $TiO_2$(001) surfaces prepared in ultra-high vacuum (UHV) with different surface treatments such as $Ar^+$-sputtering and oxidation with molecular $O_2$, respectively. We find that the saturation coverage of ethanol at RT varies depending on the amount of reduced surface defects (e.g., $Ti^{3+}$) which are introduced by $Ar^+$-sputtering. We also find that the oxidized $TiO_2$(001) surface has other type of surface defects (not related to Ti 3d state) which can dissociate ethanol for further reaction above 600 K. Our C 1s core level spectra indicate clearly resolved features for the two chemically distinct carbon atoms from ethanol adsorbed on $TiO_2$(001), showing the adsorption of ethanol proceeds without C-C bond dissociation. No other C 1s feature for a possible oxidized intermediate was observed up to the substrate temperature of 650 K.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1095-1096
• /
• 2006

When $Y_2O_3$ was added to Ti-excess $BaTiO_3$ ((Ba+Y)/Ti =1), the area occupied by $Y^{3+}$ ion was confirmed by its microstructure development, electrical conductivity behavior and lattice constant. Grain growth inhibition was observed when the content of donor dopant exceeded a critical value ($x{\approx}.0.01$) in $BaTiO_3+x(0.5Y_2O_3+TiO_2)$ system. A donor-doped behavior was observed at various Y contents ($0.2\sim3.0$ mol% Y) when $Y_2O_3$ was added to $TiO_2$-excess $BaTiO_3$. As Y content was increased, (002) and (200) peaks shifted to higher angles and the lattice constant (a and c axis) decreased gradually.