• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.146-153
• /
• 1998

The optical near-field patterns, propagation loss and mode sizes of x-cut $Ti:LiNbO_3$ optical waveguide which was fabricated by Ti-diffusion varying with Ti strip thickness in wet oxygen atmosphere were discussed at optical wavelength 1550nm. As Ti thickness increased from $760{\AA}$, the insertion loss of waveguide was decreased. But at Ti thickness $1500{\AA}$, mode sizes are widely broadened. The Ti thickness of below $1100{\AA}$ and above $1500{\AA}$ showed negative effects to propagation loss and fiber coupling. The best Ti thickness for fabricating low propagation loss and good fiber coupling was inferred to be between $1100{\AA}-1500{\AA}$ in our conditions. And for Ti thickness $1150{\AA}$, its propagation loss, horizontal/vertical mode sizes were showed 1.61 dB/cm, $11.9/8.9{\mu}m$ for TM, 0.22 dB/cm, $12.0/9.1{\mu}m$ for TE respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.282-285
• /
• 1999

Fabrication and pakaging method for low delve voltage and 10Gbps Ti diffused waveguide LiNbO$_3$ optical intensity modulator are described. Optical waveguides were prepared by conventionaly electron-beam evaporation and Ti-indiffusion into Z-cut plate LiNbO$_3$. Traveling-wave electrodes were used for obtaining the wideband frequency response and impedance matching. Microwave effective index and characteristic impedance measured by time domain reflectometry and compared with the calculated value by conformal mapping. The characteristics of 10Gbps modulator at the 1550nm wavelength are as follows : perfect modulation voltage Is about 5V, optical insertion loss Is about 5dB, 3-dB bandwidth is 10GHz, and characteristic impedance is about 50$\Omega$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1782-1792
• /
• 1994

Ti : $LiNbO_3$ traveling-wave phase optical modulators at wavelength 1.3㎛ have been designed and fabricated, focusing on the optical waveguide and asymmetric coplanar electrode structure. To improve the phase-mismatch of traveling-wave ACPS electrode, the characteristic impedance, effective microwave index, and electrode loss have been presented as a function of geometric parameters including electrode and buffer layer thickness. Low-loss channel optical waveguides on $LiNbO_3$ were fabricated by the Ti diffusion method with $O_2$ water-vapor environment. $2.5{\mu}m$ thick electrode was successfully fabricated by double-spin image reversal process. Modulation bandwidth was limited by a resonance at 2.9 GHz and modulation bandwidth up to 2.5GHz was approxirnately measured.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.254-258
• /
• 2002

To realize channel cross-connecting in optical communications systems, a high speed optical matrix switch was fabricated using z-cut $LiNbO_3$. For switch fabrication was design bending structure and coupling length and four $2{\times}2$ directional couplers were integrated on one substrate far construction of a $4{\times}4$ switch. Single-mode optical waveguides were formed by Ti-diffusion at a wet $O_2$ atmosphere. Ti-diffusion profile, refractive index variation and waveguide morphology were analyzed by Prism coupler and optical microscopy, respectively.

• Korean Journal of Optics and Photonics
• /
• v.7 no.1
• /
• pp.51-59
• /
• 1996

In this paper, we propose a new type of a planar waveguide lens, a meniscus lens instead of a plano-convex lens used widely for the optical integrated circuits such as optical numerical processors. A plano-convex lens has a spherical aberration caused by the linear boundary. In the proposed meniscus lens, this linear boundary is replaced by a circular-boundary, and the spherical aberration is removed. To test the performance of the proposed lens, a meniscus lens is designed using Fermat principle and fabricated on the Y-cut $LiNbO_3$ substrate. First a $Ti:LiNbO_3$ planar waveguide is fabricated on the $LiNbO_3$ substrate by Ti indiffusion. Then a meniscus lens is fabricated on the planar waveguide by TIPE(Ti indiffued proton-exchange) method. A plano-convex lens is also fabricated on the same substrate to compare the spot size at the focal point. The measured spot size of the meniscus lens is reduced to 59% that of the plano-convex lens. This result shows that the proposed meniscus lens is more effective for optical integrated circuits than the plano-convex lens.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.128-134
• /
• 2012

The performance evaluation and fabrication of integrated-optic electric-field sensor utilizing $Ti:LiNbO_3$ asymmetric Mach-Zehnder intensity modulator with a push-pull lumped electrode and a plate-type probe antenna to measure an electric field strength is described. The modulator has a small device size of $46{\times}7{\times}1\;mm$ and operates at a wavelength $1.3{\mu}m$. The devices are simulated based on the BPM software and fabricated utilizing Ti-diffused $LiNbO_3$ channel optical waveguides. The minimum detectable electric field is 1.02 V/m and 6.91 V/m, corresponding to a dynamic range of ~35 dB and ~10 dB at the frequencies of 500 KHz and 5 MHz, respectively.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.1
• /
• pp.72-78
• /
• 1998

Polarization mode converters have been produced by utilizing Ti:LiNbO$_{3}$ channel waveguide and strain-optic effect. Shear strain for periodic perturbations of optical channel waveguides and phase matching can be obtained by an evaporated periodic SiO$_{2}$ thin film at 300.deg. C. The electrodes located on the either side of waveguide provide a means to electro-optically tune the wavelength for maximum polarization conversion via the electrooptic effect. The maximum conversion effeciency was observed at 21.deg. C for V=0 and 46.deg. C for V=30V aro the device having 7 .mu.m waveguide wiith and 350 periodic pads. The dependence of the number of pads on conversion efficiency was observed experimentally.fficiency was observed experimentally.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.547-554
• /
• 2004

We investigated a LiNbO$_3$ based integrated-optic polarization controller with the Ti-indiffused waveguide along the z-axis utilizing the electro-optic effect. The device consists of a first quarter-wave (λ / 4) followed by a half-wave (λ / 2) and a second quarter-wave (λ / 4) wave-plate. We analyzed the amount of phase change and the transformation of the polarized mode as a function of the combination of wave-plates and of their applied voltages. The operation has been systematically measured utilizing a polarimeter and Poincare sphere. We confirmed that the fabricated device controls the transformations from any arbitrary input state of polarization (SOP) into any general output SOP.

• Korean Journal of Optics and Photonics
• /
• v.15 no.4
• /
• pp.375-384
• /
• 2004

Switching phenomenon of a three-waveguide optical coupler was analyzed by using the coupled mode theory, and the coupling-length of the device was calculated by means of the FDM. CPW traveling-wave electrodes were designed by the CMM and SOR simulation techniques so as to satisfy the conditions of phase-velocity and impedance matching. Traveling-wave modulators were fabricated on a z-cut LiNbO$_3$ substrate. Ti was in-diffused in LiNbO$_3$ to make waveguides and Au electrodes were built on the waveguides by the electroplating technique. Insertion loss and switching voltage of the optical modulator were about 4 ㏈ and 15.6V. Network analyzer was used to obtain S parameters and corresponding RF response. From the measurement, parameters of the traveling-wave electrodes were extracted as such Z$_{c}$=39.2 $\Omega$, Neff=2.48, and a0=0.0665/cm((GHz) (1/2)). The measured optical response R(w) was compared with the theoretically estimated and both responses were shown to agree well. The measurement results revealed that the ㏈ bandwidth turned out to be about 13 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.425-427
• /
• 1997

Ti:LiNbO$_3$optical waveguides were fabricated as a function of Ti thickness and pigtailed with polarization maintaining fiber(PMF). The near field patterns and total insertion loss of these sample was showed and measured for optical wavelength 1550nm. The fiber-to-waveguide coupling loss was described also .