• Korean Journal of Materials Research
• /
• v.15 no.6
• /
• pp.361-369
• /
• 2005

InP(100) crystal surface was irradiated by ion beams with low energy $(180\~225\;eV)$ and high flux $(\~10^{15}/cm^2/s)$, Self-organization process induced by ion beam was investigated by examining nano structures formed during ion beam sputtering. As an ion source, an electrostatic closed electron Hall drift thruster with a broad beam size was used. While the incident angle $(\theta)$, ion flux (J), and ion fluence $(\phi)$ were changed and InP crystal was rotated, cone-like, ripple, and anistropic nanostrucuture formed on the surface were analyzed by an atomic force microscope. The wavelength of the ripple is about 40 nm smaller than ever reported values and depends on the ion flux as $\lambda{\propto}J^{-1/2}$, which is coincident with the B-H model. As the incident angle is varied, the root mean square of the surface roughness slightly increases up to the critical angle but suddenly decreases due to the decrease of sputtering yield. By the rotation of the sample, the formation of nano dots with the size of $95\~260\;nm$ is clearly observed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.1
• /
• pp.6-10
• /
• 2001

In this study, we investigated the optical properties of sub-wavelength a-Si thin film transmission gratings, especially the polarization effect, the phase difference and the birefringence by using linearly polarized He-Ne laser beam (632.8nm). The a-Si transmission grating of the thickness $of < 0.1 \mum$ with four-type period($\Lambda = 0.4 \mum and 0.6 \mum$ for sub-wavelength and $\Lambda = 1.0 \mum and 1.4 \mum$ for above-wavelength) on quartz substrates have been fabricated using 50 KeV Ga+ Focused-Ion-Beam(FIB) Milling and $CF_4$Reactive-Ion-Etching(RIE) method. Finally, we obtained the trating array of a-Si thin film with a period $0.4 \mum, 0.6 \mum, 1.0 \mum, 1.4 \mum$ which have nearly equal finger spacing and width, sucessfully. Especially, for gratings with $\Lambda = 0.6 \mum(linewidth=0.25 \mum, linespace=0.35\mum), the \etamax at \theta_в=17.0^{\circ}$ is estimated to be 96%. As the results, we believe that the sub-wavelength grating arrayed a-Si thin film has the applicability as the optical device and components.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.297-304
• /
• 2003

This paper presents the test results of RCS(Reinforced Concrete Steel) beam-column joint with various types of transverse reinforcements such as small-column-type transverse reinforcements, four-piece ㄱ-shape assembled hoops and four-piece ㄱ-shape welded hoops. Five interior beam-column joint specimens were tested to examine the seismic performance and the shear strengths. From the test results, it was found that all the specimens sustained their strength at large levels of story drift(${\theta}$=0.035) without significant loss of strength and stiffness. Therefore it was concluded that the seismic performance and shear strength of the proposed RCS joint are at least the same as those of the specimen with conventional reinforcing details. Also, the contribution of the outer panel to the shear strength of the joint should be evaluated by the compression strut mechanism rather than compression field mechanism.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2000.11a
• /
• pp.73-80
• /
• 2000

The paper is addressed to the topic of physiological response-specificity in disgust induced by visual stimulation. The purpose of this study was to evaluate reproducibility of physiological reactivity pattern during disgust elicited by the International Affective Pictures System (IAPS) in 2 experiments. Twenty-nine subjects participated in the first experiment with 3 visual stimulation sessions with disgust-eliciting slides (3 slides in each 1 min long session). In the second experiment disgust-eliciting slides from the IAPS were presented to 42 subjects in 2 sessions (one slide for 1 min). Spectral power of frontal EEG, skin conductance (SCL, SCR and NS.SCR), heart rate(HR), heart period variability(HPV) and respiration rate were recorded. Visual stimulation evoked 1:.n deceleration, higher power of high frequency component of HPV, increased SCL and NS.SCR frequency, frontal slow alpha blocking and moderate increase in fast beta power in most of the sessions in both experiments. However in the second experiment the EEG pattern associated with disgust showed inconsistent shifts in fast alpha and slow beta bands, but was marked by higher power of theta activity. Our data in both experiments emphasizes presence of disgust-specific profiles of autonomic and at the less extent EEG responses in visual stimulation context. Discussed are potential behavioral mechanisms leading to observed physiological manifestations in disgust elicited by visual stimulation. The results support the consideration that disgust is an withdrawal type negative valence emotion associated with relatively low autonomic arousal (low HR, low amplitude SCRs with relatively high NS.SCR frequency) and moderate EEG activation signs. Obtained data showed more consistent reproducibility of disgust-specific autonomic rather than EEG response patterns during visual stimulation design.

• Korean Journal of Acupuncture
• /
• v.20 no.2
• /
• pp.31-46
• /
• 2003

Objectives : The aim of this study was to examine the effects of electroacupuncture(EA) at the BL60 (Kollyun) on normal humans using power spectral analysis. Methods : EEG power spectrum exhibit site-specific and state-related differences in specific frequency bands. In this study, power spectrum was used as a measure of complexity. 30 channel EEG study was carried out in 10 subjects $(10\;males;\;age=22.4{\pm}0.5$ years). Results : In alpha band, the power values at Fz during the non-acupoint treatment and at Fp2, T5 during the BL60-acupoint treatment significantly were decreased. In beta band, the power values at C3, Po2, O2, Oz during the BL60-acupoint treatment significantly were increased than the before-acupuncture treatment. In theta band, the power values at F7 during the BL60-acupoint treatment significantly was increased. However, the comparison with that before and after the treatment shows no significant differences in all channels.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.400-405
• /
• 2000

We investigated the effect of TMIn (trimethly-indium) source depletion on InGaAs, InGaAsP and 1.55 $\mu\textrm{m}$ InGaAs/InGaAsP SMQW by using EPISON ultrasonic monitor for measuring the concentration of metalorganic/carrier gas mixtures. And the problems for the growth reproducibility in MOCVD was solved by using an EPISON ultrasonic monitor with closed-loop mode under the condition of TMIn source depletion. The saturation pressure of TMIn was dramatically decreased over consumption of 80%. In the case of bulk epilayer, Up-shifting of 300 arcsec to Ga-rich direction and FWHM broadening by a factor of two in DCXRD spectrum were observed due to the TMIn source depletion. In the case of SMQW, Up-shifting of 300 arcsec to Ga-rich direction in DCXRD spectrum and blue-shift of 40 nm in PL spectrum were observed due to the TMIn source depletion. However, good reproducibility ($\Delta\theta$<$\pm$100 arcsec) was achieved even the condition of 95% of TMIn consumption, when we used the EPISON with closed-loop mode.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.587-595
• /
• 2017

Recent trends in slim air conditioners require heat exchangers of reduced flow depth. In this study, slim louver fin geometry was obtained using predictive correlations. The deduced geometry yielded 10 mm flow depth, 0.9 mm louver pitch, and $35^{\circ}$ louver angle. Samples were made and tests were conducted. The new slim sample yielded 36% higher j factor and 2.3% higher f factor compared with those of the standard sample. This implies that 26% reduction of heat exchanger volume was possible by reducing the flow depth. In addition, the $j/f^{1/3}$ of the slim sample was 55% larger than that of the standard sample. Furthermore, the results are compared with predictions made using existing correlations.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.461-467
• /
• 1993

The purpose of this study was to investigate the physico-chemical properties of potato starch heated with microwave. Two types of potato starches are prepared; in group A raw potato starch was heated with microwave and in group B potato starch was isolated from potato heated with microwave. Both groups were exposed to the microwave energy in a 560 W, 2,450 MHz oven for 60, 120, 180 and 300 seconds. As the microwave heating time took longer, free lipid decreased and bound lipid increased in both groups. The shape of starch granules, birefrigence and X-ray diffraction pattern were not changed much by microwave heating in both groups. Water binding capacity increased, but amylose content, swelling power and solubility decreased as the microwave heating time took longer. It was also found that the extent of decreases in swelling power and solubility were different between group A and group B.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.115-122
• /
• 2007

Recently, remarkable progress has been made in both technology and production of optical elements including aspheric lens. Especially, requirements for machining glass materials have been increasing in terms of limitation on using environment, flexibility of material selection and surface accuracy. In the past, precision optical glass lenses were produced through multiple processes such as grinding and polishing, but mass production of aspheric lenses requiring high accuracy and having complex profile was rather difficult. In such a background, the high-precision optical GMP process was developed with an eye to mass production of precision optical glass parts by molding press. This GMP process can produce with precision and good repeatability special form lenses such as camera, video camera, aspheric lens for laser pickup, $f-\theta$ lens for laser printer and prism, and me glass parts including diffraction grating and V-grooved base. GMP process consist a succession of heating, forming, and cooling stage. In this study, as a fundamental study to develop molds for GMP used in fabrication of glass lens, we conducted a glass lens forming simulation. In prior to, to determine flow characteristics and coefficient of friction, a compression test and a compression farming simulation for PBK40, which is a material of glass lens, were conducted. Finally, using flow stress functions and coefficient of friction, a glass lens forming simulation was conducted.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.264-264
• /
• 2012

As an environment-friendly alternative energy resource, ethanol may be used to obtain hydrogen, a clean energy source. Thus, studies on catalytic reactions involving ethanol have been studied to understand the underlying principles in the reaction mechanism using various oxide-supported catalysts. Among them, Au-based catalysts have shown a superior activity in producing hydrogen gas. In the present study, Au/$TiO_2$ catalysts were prepared by deposition-precipitation method to understand their catalytic activities toward ethanol and acetaldehyde with increasing gold loading, especially at the very low Au loading regime. A commercially available $TiO_2$ (Degussa P-25) was employed and the Au loading was varied to 0, 0.1, 0.5, and 1.0 wt% respectively. The catalysts showed characteristic x-ray diffraction (XRD) features at $2{\theta}=78.5^{\circ}$ that could be assigned to the presence of gold nanoparticles. Its reactivity measurements were performed under a constant flow of ethanol and acetaldehyde at a flow rate of ${\sim}0.6{\mu}mol/sec$ and the substrate temperature was slowly raised at a rate of 0.2 K/sec. We observed that the overall reactivity of the catalysts increased with increasing Au loading along with selectivity favoring dehydrogenation to product hydrogen gas. In addition, we disclosed various reaction channels involving competitive reaction paths such as dehydrogenation, dehydration, and condensation. In addition, subsequent reactions of acetaldehyde obtained from dehydrogenation of ethanol, were found to occur and produce butene, crotonaldehyde, furan, and benzene. Based on the results, we proposed overall reaction pathways of such reaction channels.