Magazine of the Korean Society of Agricultural Engineers
/
v.12
no.3
/
pp.2019-2028
/
1970
1. Experiments were made for the efficient plowing method by the 4 wheel tractor, the results are as follow; 1) In case of plowing of inner side of the field, the efficient turning method to be the smallest turning time is the $\Omega$-shaped turning method in the turning distance less than 2r (r is the minimum turning radius of the tractor), and also, it is the U-shaped turning method in the turning distance larger than 2r. 2) 2.5r is most efficient in the unit turning section 'w' on plowing of the inner side of the field. 3) In case of plowing of outer side of the field, intermitted plowing method is efficient in case of W>-0.0345 L + 35.84, and also, semi-followed plowing method is efficient in case of W<-0.0345 L + 35.84. 4) The smaller the width of outer side of outer side of the field 'I' is, the higher is the plowing efficiency, and it is estimated that the minimum value 2r is suitable to 'I' in plowing of inner side and outer side of the field. 2. Study on the correlation between the unit field and plowing efficiencies obtained the following results; 1) plowing efficienies increase generally according as length-width ratio L/W and area A increase. 2) Percent of increase of plowing efficiencies decreases generally according as length-width ratio and area enlarge. 3) The limit that change of T is large owing to L/W is 6 for 20 a, 5 for 30 a, 4 for 50 a, 3 for 80 a, less than 2.5 for 100 a, generally, in L/W-T curve. 4) Rate of change of T-A curve is similar to rate of change of $T=A-\frac{2}{3}$ curve in spite of influence of L/W. 5) In case that length-width ratio is more than 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 5 increase of length width ratio without correlation of size of the field. 6) In case that length-width ratio is 2 to 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 4 to 2 increase of length-width ratio without correlation of size of the field, and the effects decrease according as not only length-width ratio decreases but also area increases, generally.
Single phase $CuInS_2$ thin film with a highest diffraction peak (112) at a diffraction angle ($2{\theta}$) of 27.7$^{\circ}$ was well made by SEL method at annealing temperature of 250 $^{\circ}C$ and annealing hour of 60 min in vacuum of $10^{-3}$ Torr or in S ambience for an hour. And the peak of diffraction intensity at miller index (112) of $CuInS_2$ thin film annealed in S ambience was shown a little higher about 11 % than in only vacuum. Single phase $CuInS_2$ thin films were appeared from 0.85 to 1.26 of Cu/In composition ratio and sulfur composition ratios of $CuInS_2$ thin films fabricated in S ambience were all over 50 atom%. Also when Cu/In composition ratio was 1.03, $CuInS_2$ thin film with chalcopyrite structure had the highest XRD peak (112). And lattice constant a and grain size of the thin film in S ambience were appeared a little larger than those in only vacuum. The largest lattice constant of a and grain size of $CuInS_2$ thin film in S ambience was 5.63 ${\AA}$ and 1.2 ${\mu}$m respectively. And the films in S ambience were all p-conduction type with resistivities of around $10^{-1}{\Omega}cm$.
A total of 150 growing ducks were assigned to five dietary treatments to study the effect of sea tangle and charcoal (STC) supplementation on growth performance and meat characteristics in a completely randomized design. There were six replicates and five ducklings in each replication. The five dietary treatments were control, antibiotic, and 0.1%, 0.5%, and 1% STC supplemented diets. No significant differences were found on ADG, ADFI, and gain:feed among treatments in different weeks. The overall (0 to 3 weeks) ADFI decreased in antibiotic treatment (p<0.05) whereas the gain:feed increased significantly upon 1.0% STC supplementation compared to control (p<0.05). No significant variation was found in meat chemical composition except crude fat content which was high in 1.0% STC dietary group (p<0.05). Meat cholesterol was reduced in 0.1% STC group (p<0.05) compared to other dose levels while serum cholesterol was unaffected. High density lipoprotein (HDL) content was high in 1.0% STC (p<0.05) and low density lipoprotein (LDL) was low in 0.1% and 1.0% STC dietary groups (p = 0.06). No significant effect was found on the thiobarbituric acid reactive substances (TBARS) of fresh meat, whereas the TBARS value of meat preserved for 1 week was reduced significantly in STC dietary groups (p<0.05). The 0.1% STC dietary group showed an increased myristic acid (p = 0.07) content whereas, the content of eicosapentaenoic (EPA) and docosahexaenoic (DHA) acids increased in STC supplementation than antibiotic group (p<0.05). An increased concentration of omega-3 fatty acids and a reduced ratio of n-6/n-3 PUFA ratio was found upon 1.0% STC supplementation compared to antibiotic dietary group (p<0.05). Therefore, 1.0% STC dietary supplementation can be used as alternatives to antibiotics in duck production.
Proceedings of the Korean Vacuum Society Conference
/
2012.08a
/
pp.141-141
/
2012
The electronic and optical properties of Indium Zinc Tin Oxide (IZTO) thin films using gas environment were investigated by X-ray photoelectron spectroscopy (XPS) and reflection electron energy loss spectroscopy (REELS). REELS spectra revealed that the band gaps of IZTO thin films are 3.26, 3.07, and 3.46 eV for water mixed with oxygen, argon mixed with oxygen, and air environments, respectively. The measured band gaps by REELS are consistent with the optical band gaps obtained by UV-Spectrometer. The optical properties represented by the dielectric function $\mathfrak{m}$, the refractive index n, the extinction coefficient k, and the transmission coefficient T of the IZTO thin films with different gas environments were determined from a quantitative analysis of REELS spectra. The calculated transmission from quantitative analysis of REELS spectra shows good agreement with transmission measured by UV-spectrometer. The transmission values of 89% and low electrical resistivity of $3.55{\times}10^{-3}{\Omega}{\cdot}cm$ have been achieved for argon mixed with oxygen which indicates that the gas enviroment plays an important role in improving the electronic and optical properties of films.
$CuInS_2$ thin films were synthesized by sulfurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furnace annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1 : 1 : 2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}$ [$cm^{-3}$], 312.502 [$cm^2/V{\cdot}s$] and $2.36{\times}10^{-2}$ [${\Omega}{\cdot}cm$], respectively.
Prasad, Deepak Divashkar;Zullah, Mohammed Asid;Kim, You-Taek;Lee, Young-Ho
한국신재생에너지학회:학술대회논문집
/
2010.06a
/
pp.237.1-237.1
/
2010
Recent developments such as concern over global warming, depletion of fossil fuels and increase in energy demands by the increasing world population has eventually lead to mass production of electricity using renewable sources. Ocean contains energy in form of thermal energy and mechanical energy: thermal energy from solar radiation and mechanical energy from the waves and tides. The current paper looks at generating power using waves. The primary objective of the present study is to maximize the primary energy conversion (first stage conversion) of the base model by making some design changes. The model entire consisted of a numerical wave tank and the turbine section. The turbine section had three components; front guide nozzle, augmentation channel and the rear chamber. The augmentation channel further consisted of a front nozzle, rear nozzle and an internal fluid region representing the turbine housing. Different front guide nozzle configuration and rear chamber design were studied. As mentioned, a numerical wave tank was utilized to generate waves of desired properties and later the turbine section was integrated. The waves in the numerical wave tank were generated by a piston type wave maker which was located at the wave tank inlet. The inlet which was modeled as a plate wall which moved sinusoidally with the general function, $x=asin{\omega}t$. In addition to primary energy conversion, observation of flow characteristics, pressure and the velocity in the augmentation channel, rear chamber as well as the front guide nozzle are presented in the paper. The analysis was performed using the commercial code of the ANSYS-CFX. The base model recorded water power of 29.9 W. After making the changes, the best model obtained water power of 37.1 W which represents an increase of approximately 24% in water power and primary energy conversion.
Journal of the Korean Institute of Telematics and Electronics D
/
v.36D
no.3
/
pp.59-65
/
1999
In this paper, we had studied the possibility of application as Cu thin films from (hfac)Cu(VTMOS) which is very stable. Cu thin films had been studied as a function of deposition temperature. Substrates used in the experiment were PVD TiN on Si wafer. Deposition conditions were as follow : deposition temperature $50^{\circ}C$. Cu thin films were analyzed by AES, four point probe, XRD and SEM. All of deposited films were very pure and some favoring of <111> planes perpendicular to the substrate surface were observed. Cu thin films had two distinct growth rates at various deposition temperature. One is the surface reaction limited region below $200^{\circ}C$, and the other is the mass transport limited region above $200^{\circ}C$. The resistivity of deposited Cu thin films under the optimum deposition condition is $2.5mu\Omega.cm$ Thus, properties of deposited Cu thin films using (hfac)Cu(VTMOS) didn't show difference with Cu thin films from other precursors.
Objectives : Hippocampus, a region of temporal lobe, plays an important role in the pathogenic mechanisms of brain diseases such as Alzheimer's disease, depression and temporal lobe epilepsy. This research is designed to investigate hippocampal changes after acupuncture stimulation at Shinmun(HT7) using 2-dimensional gel electrophoresis(2-DE). Methods : On postnatal-day 15, rat pups were randomly devided into Normal(NOR) or HT7 group. All of Pups kept with their mothers for 7 days, but pups in HT7 group received acupuncture stimulation at HT7 daily. On postnatal-day 21, hippocampus of each rat pup was dissceted 30 minutes after last acupuncture stimulation and the protein expressions were investigated using 2-DE. Results : After acupuncture stimulation at HT7, expression of 20 proteins were significantly increased. Succinate semialdehyde dehydrogenase, glyceraldehyde-3-phosphate dehydrogenase-like, transketolase, aconitate hydratase and phosphoglucomutase-1 were related to glucose methabolism. Eukaryotic initiation factor(eIF) 4A-II, eIF 4A-III, mitochondrial Tu translation elongation factor and chain A of crystal structure of the 70-Kda heat shock cognate protein involve in the protein synthesis in ribosome. Tubulin ${\beta}$-4 chain, tubulin T ${\beta}$-15 and tubulin ${\alpha}$-1B chain comprise cytoskeleton. Glutathione S-transferase(GST) ${\omega}$-1, GST P and GST Yb-3 can reduce oxidative stress. ${\beta}$-soluble N-ethylmaleimide-sensitive fusion protein attachment protein is required for vesicular transport between the endoplasmic reticulum and the Golgi apparatus, glycerol-3-phosphate dehydrogenase plays a major role in lipid biosynthesis, creatine kinase U-type catalyses the conversion of creatine and consumes adenosine triphosphate to create phosphocreatine and adenosine diphosphate. Platelet-activating factor acetylhydrolase IB subunit alpha and voltage depedent anion-selective channel protein 2 were also increased. Conclusions : The results suggest that acupuncture stimulation at HT7 may enhance glucose and lipid metabolism, protein synthesis, cytoskeletal substance and anti-oxidative stress in hippocampus.
This study aimed to provide basic information as the foundation for further studies on the assessment of velvet antler quality by investigating the changes in fatty acid, vitamin A and E, minerals and GAGs contents by development stage of antler in spotted deer (Cervus nippon). Twelve stags (aged 4 to 5 years) were divided into two groups and velvet antler harvested 40 days (FDG) and 60 days (SDG) after casting of the buttons from the previous set. Total saturated fatty acid was lower in FDG than SDG (p<0.05). Total monounsaturated fatty acid, conjugated linoleic acid (p<0.05), polyunsaturated fatty acid and ${\omega}$3 fatty acid were higher in FDG than SDG. The vitamin A content of FDG was higher than that of SDG, but the vitamin E content of FDG was lower than that of SDG (p<0.05). SDG had significantly higher calcium and phosphate content than FDG (p<0.05). The magnesium content showed a similar trend to the contents of calcium and phosphate, but there was no significant difference between SDG and FDG. Uronic acid content was higher in FDG than SDG but there was no significant difference. The contents of GAGs and sialic acid were significantly higher (p<0.05) in FDG than SDG. These results indicated that the longer stage of antler development had lower content of activating components and this lead to a decrease of antler quality.
This paper describes the development and assessment of conductive fabric sensor for evaluating knee movement using bio-impedance measurement method. The proposed strip-typed conductive fabric sensor is compared with a dot-typed Ag/AgCl electrode for evaluating validity under knee movement condition. Subjects are composed of ten males($26.6{\pm}2.591$) who have not had problems on their knee. The strip-typed conductive fabric sensor is analyzed by correlation and reliability between a dot-typed Ag/AgCl electrode and the strip-typed conductive fabric sensor. The difference of bio-impedance between a dot-typed Ag/AgCl electrode and the strip-typed conductive fabric sensor averages $7.067{\pm}13.987\;{\Omega}$ As the p-value is under 0.0001 in 99% of t-distribution, the strip-typed conductive fabric sensor is correlated with a dot-typed Ag/AgCl electrode by SPSS software. The strip-typed conductive fabric sensor has reliability when it is compared with a dot-typed Ag/AgCl electrode because most of bio-impedance values are in ${\pm}1.96$ standard deviation by Bland-Altman Analysis. As a result, the strip-typed conductive fabric sensor can be used for assessing knee movement through bio-impedance measurement method as a dot-typed Ag/AgCl electrode. Futhermore, the strip-typed conductive fabric sensor is available for wearable circumstances, applications and industries in the near future.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.