• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.51-54
• /
• 2000

In this paper, $Ba_{0.5}$Sr$_{0.5}$TiO$_3$ thin films were prepared on Pt/Ti/SiO$_2$/Si substrate by RF magnetron sputtering method. We investigated effect of deposition conditions (especially RF input power) on structural properties of BST thin films. Deposit conditions of BST films were set working gas ratio, Ar:O$_2$= 70 : 30, working pressure 10mTorr, and RF input power 25W, 50W, 75W and 100W. Post-annealing using rapid thermal annealing(RTA) performed at 45$0^{\circ}C$, 55$0^{\circ}C$, $650^{\circ}C$, and 75$0^{\circ}C$ in oxigen ambient for 60 sec, respectively. The structural properties of BST films on Pt/Ti/SiO$_2$/Si substrate analysed by X-ray diffraction(XRD).).).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.5.2-8
• /
• 1995

0.15($Ba_{1-x}Sr_{x}$)O-$0.15Sm_2O_3$-$0.7TiO_2$(x=0∼9[m/o]ceramics were fabricated by mixed-oxide method. Microwave dielectric properties were investigated with sintering conditions aid Sr addictive. In the specimen with x=0[m/o] sintered at 1350∼1470[$^{\circ}C$], dielectric constant, quality factor and temperature coefficient of resonant frequency were 70∼74, 2800∼3300(at 3[GHz]), -1.33∼+l.66[ppm/$^{\circ}C$, respectively. Increasing the Sr additive from 0 to 5[m/o], dielectric constant and temperature coefficient of resonant frequency were increased and quality factor was decreased. In the specimen with x=r[m/o] sintered at 1375[$^{\circ}C$], 6[hr], dielectric constant, quality factor and temperature coefficient resonant frequency were 75.62, 2785(at 3[GHz]), +8.39[ppm/$^{\circ}C$], respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.3
• /
• pp.468-473
• /
• 2003

In this paper, for enhancement of property on a-Si:H TFTs We measure interface characteristics of ferroelectrics thin film and a-Si:H thin film. First, SrTiO$_3$ thin film is deposited bye-beam evaporation. Deposited films are annealed for 1 hour in N2 ambient at $150^{\circ}C∼600^{\circ}C$. Dielectric characteristics of deposited SrTiO$_3$ films are very good because dielectric constant shows 50∼100 and breakdown electric field are 1 ∼ 1.5 MV/cm. a-SiN:H,a-Si:H(n-type a-Si:H) are deposited onto SrTiO$_3$ film to make MFNS(Meta1/ferroelectric/a-SiN:H/a-Si:H) by PECVD. After the C-V measurement for interface characteristics, MFNS structure shows no difference with MNS(Metal/a-SiN:H/a-Si:H) structure in C-V characteristics but the insulator capacitance value of MFNS structure is much higher than the MNS because of high dielectric constant of ferroelectric.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.2
• /
• pp.427-430
• /
• 2008

BaTiO3 and SrTiO3 thin films were fabricated on Pt/Ti/SiO2/Si substrate by the pulsed laser deposition process. The dependence of the deposited film quality upon the partial oxygen pressure during the deposition process was importantly examined. Regardless of the oxygen pressure, the as-deposited films were not fully crystallized. However, the film deposited at low oxygen pressure became well crystallized after the annealing process. It was concluded, therefore, that the partial oxygen pressure is reduced as low as possible during the deposition process and then anneal the as-deposited samples at ambient pressure to fabricate the well crystallized SrTiO3 and BaTiO3 films by laser ablation.

• Journal of Magnetics
• /
• v.18 no.1
• /
• pp.39-42
• /
• 2013

We studied the structural and electrical properties of $SrRuO_3$ thin films grown on $SrTiO_3$ (110) substrate. High resolution X-ray diffraction measurement of the grown film showed 1) very sharp peaks for $SrRuO_3$ film with a very narrow rocking curve with FWHM = $0.045^{\circ}$ and 2) coherent growth behavior having the same in-plane lattice constants of the film as those of the substrate. The resisitivity data showed good metallic behavior; ${\rho}$ = 63(205) ${\mu}{\Omega}{\cdot}cm$ at 5 (300) K with a residual resistivity ratio of ~3. The observed kink at ${\rho}(T)$ showed that the ferromagnetic transition temperature was ~10 K higher than that of $SrRuO_3$ thin film grown on $SrTiO_3$ (001) substrate. The observed rather lower RRR value could be partially due to a very small amount of Ru vacancy generally observed in $SrRuO_3$ thin films grown by PLD method and is evident in the larger unit-cell volume compared to that of stoichiometric thin film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.5
• /
• pp.214-217
• /
• 2011

A fresnoite glass-ceramics has been investigating considerably because of the second order nonlinearity as well as its permanent optical nonlinearity. However, the chemical compositions of transparent glass-ceramics examined in the previous studies have been limited to adjust the composition close to fresnoite stoichiometrically. In this study, to investigate the effect of strontium ions in glass-ceramics on second order nonlinearity, $K_2O-TiO_2-SiO_2$ (KTS) glasses soaked in molten $Sr(NO_3)_2$ were prepared. Crystalline phases of the soaked glasses were measured by X-ray diffraction (XRD) as soaking times and additional heat treatment. The exchange of strontium ions into the glass was verified by Field Emission Scanning Electron Microscope (FE-SEM). And the phenomena of second order harmonic generation (SHG) was observed using Nd-YAG laser.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.516-524
• /
• 1995

In this study, to prepare the dielectric (Ba, Sr)TiO3 thin films by the sol-gel process, Titaminum (IV) sio-propoxide (Ti[OCH(CH3)2]4), Ba and Sr acetate were used for sol and thin films were prepared by dip-coating process. Stability of sol decreased with the increase of Sr, and thickness of thin films were obtained 0.13~0.17${\mu}{\textrm}{m}$ by 1 coating cycle. Transmittance of amorphous thin films heated at 500 and 55$0^{\circ}C$ was very good, and crystallization tendency of thin films according to heat-treatment temperature and crystallization characteristics of thin films heated at 11$0^{\circ}C$ for 3 hrs were analysed. As a result, good perovskite structure was obtained higher than 100$0^{\circ}C$, and tetragonality of thin film was decreased but pyrochlore was formed with increasing Sr. In case of addition to substitute 0.4mol% Sr for Ba, dielectric constant was 288 and loss factor (tan $\delta$) was 0.04.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.121-124
• /
• 1999

The (Ba,Sr)TiO$_3$[BST] thin film were fabricated on the Pt/Ti/SiO$_2$/Si substrate by RF sputtering technique. The structural properties of the BST thin films were investigated with deposition time and substrate temperature by XRD. In the case of the BST thin films which has the deposition thin of 20 min, second phases and BST (111) peaks were increased with increasing the temperature of substrate. The capacitance of the BST thin film (deposition time of 20 min.) was decreased with the substrate temperature and was 1500pF with applied voltage of 1V.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.767-772
• /
• 1999

The effect of B2O3 addition on the sintering behavior dielectric and ferroelectric properties of Ba0.7Sr0.3TiO3 ceramics were investigated. The sample with 0.5wt% B2O3 was sintered under 115$0^{\circ}C$. The dielectric and ferroelectric properties of BST with 0.5wt% B2O3 was as good as BST without B2O3 sintered at 135$0^{\circ}C$ and its dielectric loss was even better When B2O3 was added over 1.0wt% the overdoped B2O3 remained in the specimens and formed a second phase which degraded the sintering behaivor dielectric properties of BST.

• Journal of the Korean Chemical Society
• /
• v.7 no.4
• /
• pp.254-256
• /
• 1963

A spectrochemical analysis was made to compare the major impurities in $BaTiO_3$ single crystals grown from $KF-BaTiO_3$ system and $TiO_2-BaTiO_3$ system respectively. The present technique was also extended, without any modifications, to the analysis of $SrTiO_3$ crystal.