• Resources Recycling
• /
• v.10 no.5
• /
• pp.29-35
• /
• 2001

This study was carried out to recover gold, silver and valuable metals from the printed circuit boards (PCBs) of waste computers. PCBs samples were crushed under 1 mm by a shredder and separated into 30% conducting and loft nonconducting materials by an electrostatic separator. The conducting materials contained valuable metals which were then used as feed materials for magnetic separation. 42% of magnetic materials from the conducting materials was removed by magnetic separation as nonvaluable materials and the others, 58% of non magnetic materials, was used as leaching samples containing 0.227 mg/g Au and 0.697 mg/g Ag. Using the materials of leaching from magnetic separation, more than 95% of copper, iron, zinc, nickel and aluminium was dissolved in 2.0M sulfuric acid solution, added with 0.2M hydrogen peroxide at $85^{\circ}C$. Au and Ag were not extracted in this solution. On the other hand, more than 95% of gold and 100% of silver were leached by the selective leaching with a mixed solvent (0.2M($NH_4$)$_2$$S_2$$O_3$,0.02M $CuSO_4$,0.4M $NH_4$OH). Finally, the residues were reacted with a NaCl solution to leach Pb whereas sulfuric acid was used to leach Sn. Recoveries reached 95% and 98% in solution, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.1945-1950
• /
• 2010

Solvent extraction experiments of Pt(IV), Pd(II) and Rh(III) by Alamine336 were performed from the mixed chloride solutions. In the HCl concentration range from 1 to 5 M, most of Pt and Pd were extracted from the mixed solutions. However, the extraction percentage of Rh was much smaller than that of Pt and Pd. Lower concentration of Alamine336 in strong HCl solution led to higher separation factor of Rh from Pt and Pd. Adding $SnCl_2$ to the mixed solutions increased the extraction percentage of Rh, while the extraction percentage of Pt and Pd was little affected. Our results showed that selective separation of Rh or coextraction of the three platinum group metals from the mixed solution would be possible by adjusting the extraction conditions.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.193-197
• /
• 2001

This study was carried out to recover gold, silver and other valuable metals from the printed circuit boards (PCB) of waste computers. PCB samples were crushed to under 1mm by a shredder and initially separated into 30% conducting and 70% non-conducting materials by an electrostatic separator. The conducting materials, which contained the valuable metals, were then used as the feed material for magnetic separation where it was found that 42% was magnetic and 58% non- magnetic. The non-magnetic materials contained 0.227mg/g Au and 0.697mg/g Ag. Further leaching of the non-magnetic component using 2.0M sulfuric acid and 0.2M hydrogen peroxide at 85$^{\circ}C$ extracted more than 95% copper, iron, zinc, nickel and aluminium. Au and Ag were not extracted in this solution, however, more than 95% of Au and 100% of Ag were selectively leached with a mixed solvent (0.2M ammonium thiosulfate, 0.02M copper sulfate, 0.4M ammonium hydroxide). Finally, the residues were reacted with a NaCl solution to leach out Pb while sulfuric acid was used to leach out Sn. Recoveries reached 95% and 98% in solution, respectively.

• Resources Recycling
• /
• v.20 no.2
• /
• pp.60-66
• /
• 2011

Solvent extraction experiments were carried out to recover and separate Ru(III) from aqueous hydrochloric acid media using TBP and Cyanex923. The efficiency of the extraction was studied under various experimental conditions, such as concentration of HCl and NaCl, concentration of extractant in the organic phase and temperature. The extraction behavior of metal impurities, such as Pt, Bi, Sn, Fe, Pb and Cu in mixed solutions was examined. From the experimental studies, it was found that the Cyanex923 resulted in higher extraction percentage of Ru than TBP. However TBP was more effective for the separation of Ru and Pt, Bi, Sn in mixed solutions than Cyanex923.

• Resources Recycling
• /
• v.17 no.2
• /
• pp.70-75
• /
• 2008

A study on the cementation for the recovery of tin with aluminium in the hydrochloric acid solution was carried out. Parameters, such as aluminium metal equivalent, pH, reaction time, reaction temperature and the concentration of chloride ions were investigated. The experimental results showed that the cementation rate of Sn(II) ions increased with increase of the addition amount of aluminium powders, temperature, pH and the concentration of chloride ions in hydrochloric acid solution. From the results, the optinum conditions for recovery of metallic tin by cementation with aluminium metal powders were proposed.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.1
• /
• pp.29-36
• /
• 2019

Corrosion inhibition by synthesised ligand, 2-acetylpyridine 4-ethyl-3-thiosemicarbazone (HAcETSc) and its tin(IV) complex, dichlorobutyltin(IV) 2-acetylpyridine 4-ethyl-3-thiosemicarbazone ($Sn(HAcETSc)BuCl_2$) on mild steel in 1 M hydrochloric acid (HCl) was studied using weight loss measurement, potentiodynamic polarisation, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The inhibition efficiency increases by increasing the inhibitor concentrations. The polarisation study showed that both synthesised compounds were mixed type inhibitors. The electrochemical impedance study showed that the presence of inhibitors caused the charge transfer resistance to increase as the concentration of inhibitors increased. The adsorption of these compounds on mild steel surface was found to obey Langmuir's adsorption isotherm with the free energy of adsorption ${\Delta}G{^o}_{ads}$ of -3.7 kJ/mol and -7.7 kJ/mol for ligand and complex respectively, indicating physisorption interaction between the inhibitors and 1 M HCl solution.

• Clean Technology
• /
• v.28 no.1
• /
• pp.38-45
• /
• 2022

CuCl₂-loaded V₂O₅-WO₃/TiO₂ catalyst showed excellent activity in the catalytic oxidation of elemental mercury to oxidized mercury even under SCR condition in the presence of NH₃, which is well known to significantly inhibit the oxidation activity of elemental mercury by HCl. Moreover, it was confirmed that, when SO₂ was present in the reaction gas together with HCl, excellent elemental mercury oxidation activity was maintained even though CuCl₂ supported on the catalyst surface was converted to CuSO₄. This is thought to be because not only HCl but also the SO₄ component generated on the catalyst surface promotes the oxidation of elemental mercury. However, in the presence of SO₂, the total mercury balance before and after the catalytic reaction was not matched, especially as the concentration of SO₂ increased. In order to understand the cause of this, further studies are needed to investigate the effect of SO₂ in the SnCl₂ aqueous solution employed for mercury species analysis and the effect of sulfate ions generated on elemental mercury oxidation. It was confirmed that SO₂ also promotes NO_x removal activity, which is thought to be because the increase in acid sites by SO₄ generated on the catalyst surface by SO₂ facilitates NH₃ adsorption. The composition change and structure of the components present on the catalyst surface under various reaction conditions were measured by XRD and XRF. These measurement results were presented as a rational explanation for the results that SO₂ enhances the oxidation activity of elemental mercury and the NO_x removal activity in this catalyst system.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.9 no.3
• /
• pp.47-57
• /
• 2007

This study focused on the properties natural dyeing and natural material and on the development of functional material for well-being in apparel industry. Comus officinalis Siebold et Zuccarini is used as natural dyeing material which had been reported that have curable effect for unbalanced immunity, geriatric diseases like urinary tract system, diabetes, hypertension, arthritis, tinnitus, hyperhidrosis and women's diseases like hypermenorrhea. And this material also has anti-cancer effect so that can restraint cancer cells. 3 kinds tester of cotton, wool and silk are dyed by boiled with each dye (flower, fruits, bark of tree) as first dyeing and dried in the shade. These testers are done by post-mordanting method. Aluminium Potassium(Alk(SO4)2), Cuprie Sulfate($CuSO4{\cdot}5H2O$), Stannous Chloride($SnCl2{\cdot}2H2O$), Ferrous Sulfate($FeCl2{\cdot}4H2O$), Titanium Sulfate 24% aqueous solution(Ti(SO4)2) are used as mordants. Dyeing results of Comus officinalis Siebold et Zuccarini flower and bark are shown as yellow color series. And dyeing result of fruits is pink color series. Silk shows the best dyeing property. As the point of view for dyeing property, Ti, Sn, Fe would be the properchoice for mordant. Following results are extracted in this study. Yellow color is resulted in dyeing with Cornus officinalis flower as non-mordanting condition. Yellowish red color is come from dyeing with Comus officinalis fruit as non-mordanting condition. Grayish yellow tone is resulted in dyeing with bark as non-mordanting condition. Orange tone color with Ti-mordanting, green tone color with Sn-mordanting and gray tone color with Fe-mordanting is resulted respectively. However light-fastness of Comus officinalis(flower, fruit, bark) is very low as 1 or 2 level in non-mordanting condition, Comus officinalis flower dyeing is turned out 3 or 4 level and fruit dyeing is 4 or 5 level, bark dyeing is 2 or 3 level with Ti-mordanting respectively. Eventually Comus officinalis fruit has the best light-colorfastness property among all of dyes. dry cleaning colorfastness of Cornus officinalis(flower, fruit, bark) is good as 4 or 5 level in Ti-mordanting condition, perspiration-colorfastness of Cornus officinalis(flower, fruit, bark) is good as 4 or 5 level in Ti-mordanting condition, With these results, this study could conclude that dye-ability, colorfastness problem is getting better after mordanting process and practical usage would be possible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.874-877
• /
• 2004

We carried out this subject to observe electrochemical properties of 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group by using cyclic voltammetry with a three-electrode system, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode in $NaClO_4$ solution. We investigated the photoisomerization and electrochemical property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of BASH and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150 and 200 mV/s. As a results, LB films of BASH-DMPC appeared reversible process caused by the reduction-oxidation current from the cyclic voltammogram.

• Corrosion Science and Technology
• /
• v.19 no.2
• /
• pp.100-107
• /
• 2020

The demand for powder-coated steel used in the marine industry is increasing owing to their superior corrosion resistance. However, the powder coatings used in commercial products can deteriorate easily by the penetration of brine. In an attempt to suppress brine penetration into the powder coating and significantly increase the corrosion resistance, three types of oxide particles were added to the coating. Electrochemical impedance spectroscopy tests in 3.5% NaCl solution were performed to evaluate the corrosion behaviors of the powder coating with oxide particles. The results showed that the addition of SiO₂ particles to a powder coating severely decreased the corrosion resistance due to the easy detachment of agglomerated SiO₂ particles with a coarse size from the coating layer. In contrast, the TiO₂ and SnO₂-added coatings showed better corrosion resistance, and the TiO₂-added coating performed best in the test conducted at room temperature. However, conflicting results were obtained from tests conducted at a higher temperature, which may be attributed to the effective suppression of brine penetration by the fine SnO₂ particles uniformly distributed in the coating.