• Advanced Composite Materials
• /
• v.18 no.4
• /
• pp.351-364
• /
• 2009

The thermal stability and elevated temperature mechanical properties of $SiC_P$/Al-11.7Fe-1.3V-1.7Si (Al-11.7Fe-1.3V-1.7Si reinforced with SiC particulates) composites sheets prepared by spray deposition (SD) $\rightarrow$ hot pressing $\rightarrow$ rolling process were investigated. The experimental results showed that the composite possessed high ${\sigma}_b$ (elevated temperature tensile strength), for instance, ${\sigma}_b$ was 315.8 MPa, which was tested at $315^{\circ}C$, meanwhile the figure was 232.6 MPa tested at $400^{\circ}C$, and the elongations were 2.5% and 1.4%, respectively. Furthermore, the composite sheets exhibited excellent thermal stability: the hardness showed no significant decline after annealing at $550^{\circ}C$ for 200 h or at $600^{\circ}C$ for 10 h. The good elevated temperature mechanical properties and excellent thermal stability should mainly be attributed to the formation of spherical ${\alpha}-Al_{12}(Fe,\;V)_3Si$ dispersed phase particulates in the aluminum matrix. Furthermore, the addition of SiC particles into the alloy is another important factor, which the following properties are responsible for. The resultant Si of the reaction between Al matrix and SiC particles diffused into Al matrix can stabilize ${\alpha}-Al_{12}(Fe,\;V)_3Si$ dispersed phase; in addition, the interface (Si layer) improved the wettability of Al/$SiC_P$, hence, elevated the bonding between them. Furthermore, the fine $Al_4C_3$ phase also strengthened the matrix as a dispersion-strengthened phase. Meanwhile, load is transferred from Al matrix to SiC particles, which increased the cooling rate of the melt droplets and improved the solution strengthening and dispersion strengthening.

• Korean Journal of Crystallography
• /
• v.1 no.1
• /
• pp.19-28
• /
• 1990

6H-SiC is a promising material (Eg=3.0eV) for blue light-emitting doide and high-temperature semiconducting device. In the experiment, single crystals of a-SiC have been grown by the sublimation method to fabricate blue light~emitting diode. During the growth of a-SiC single crystals, a temperature Vadient, yonh temperature and pressure ranges were kept 44℃/cm , 1800-1990℃ and 50-1000 mTorr, respectively. Single crystals obtained in Acheson furnace were used as seed crystals. Polarizing microscopy and back-reflection X-ray Laue diffraction showed that the a-SiC crystal was epitaxially and on the seed crytal. It was found by XRD analysis that when other growth conditions were the same, a-SiC was grown at the temperature above 1840℃ and 3C-SiC was gown at lower temperature or under low supersaturation of vapor. The carrier type. concentration and mobility were measured be hole(p-type), 7.6x1014cm-3 and 19cm2V-1sec-1, respectively, by van der Pauw method.

• Korean Chemical Engineering Research
• /
• v.57 no.5
• /
• pp.714-722
• /
• 2019

Catalysts were prepared by using incipient wetness impregnation method with 17 wt% Ni on a support ($SiO_2-Y_2O_3$, $Al_2O_3$, $SiO_2-ZrO_2$, $SiO_2$, $TiO_2$, MgO) and the catalytic activity in the reductive amination of ethanol with ammonia in the presence of hydrogen was compared and evaluated. The catalysts used before and after the reaction were characterized using X-ray diffraction, nitrogen adsorption, ethanol-temperature programmed desorption (EtOH-TPD), isopropanol-temperature programmed desorption (IPA-TPD), and hydrogen chemisorption etc. In the case of preparing $ZrO_2$ and $Y_2O_3$ supports, the small amount of Si dissolution from the Pyrex reactor surface provoked the formation of mixed oxides $SiO_2-ZrO_2$ and $SiO_2-Y_2O_3$. Among the catalysts used, $Ni/SiO_2-Y_2O_3$ catalyst showed the best activity, and this good activity was closely related to the highest nickel dispersion, and low desorption temperature in EtOH-TPD and IPA-TPD. The low catalytic activity on Ni/MgO catalysts showed low activity due to the formation of NiO-MgO solid-solutions. In the case of $Ni/TiO_2$, the reactivity was low due to the low nickel metal phase due to strong metal-support interaction. In the case of using a support as $SiO_2-Y_2O_3$, $Al_2O_3$, $SiO_2-ZrO_2$, and $SiO_2$, the selectivities of ethylamines and acetonitrile were not significantly different at similar ethanol conversion.

• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.731-739
• /
• 1993

R-curve measurements were performed on Al2O3(matrix)-ZrO2-SiC whisker composite and Al2O3-ZrO2, Al2O3-SiC whisker composites in the favor of comparing the effect of ZrO2 and SiC whisker, as a second phase, to Al2O3 matrix. Al2O3-SiC whisker and Al2O3-ZrO2-SiC whisker were fabricated by hot pressing at 1$700^{\circ}C$, 15MPa and Al2O3-ZrO2 by pressureless sintering at 1$600^{\circ}C$. A controlled flaw/strength technique was utilized to determine fracture resistance as a function of crack extension and R-curve behaviour was determined from the relationship which is KR=K0(Δa)m. R-curveresults were KR=6.173$\times$Δa0.031 for Al2O3-ZrO2, KR=18.796$\times$Δa0.172 for Al2O3-SiC whisker and KR=11.96$\times$Δa0.110 for Al2O3-ZrO2-SiC whisker composite. From the analysis of R-curve and expeirmental data above three composites, it is found that R-curve behaviour of Al2O3-ZrO2-SiC whisker composite was dominated initially by the strengthening effect of ZrO2 and after, some extended crack were influenced by the effect of SiC whisker. Analysis of SEM and X-ray data revealed that whisker bridging in the crack wake and whisker pull-out mechanisms were the main mechanism for the R-curve behaviour.

• Journal of the Korean Chemical Society
• /
• v.38 no.3
• /
• pp.241-245
• /
• 1994

The oxidative addition reaction has been employed to synthesize heteropolynuclear compounds containing Si-M bonding interaction between the silicon atom of silatrane, pentacoordinate silicon derivative with transannular Si-N dative bond, and the main group element. The reaction of $SnBr_2 with 1-bromosilatrane(1a) in acetonitrile gives the mixture of yellow(2a) and white(2b) solids which were isolated and charaterized by ^1H-NMR, ^{29}Si-NMR, ^{119}Sn-NMR and Mass spectroscopy. The yellow compound was characterized as 1-tribromotinsilatrane which had Si-Sn bonding interaction. The reaction of SnBr2 with 1-bromo-3,7,10-trimethylsilatrane(1b) in methanol gives the Sn(Ⅳ) complex, N[CH_2CH(CH_3)O]_3SiSnBr_3(CH_3OH)_2(3),$ which was characterized by various means.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.259-263
• /
• 1998

WSi2/CVD-Si/SiO2/Si-substrate의 폴리사이드 구조에서 실리콘 증착 POCl3 확산 그리고 WSi2 증착 유무에 따른 Thin oxide 특성을 연구했다 WSi2 막을 증착하지 않은 CVD-Si/SiO2/Si-substrate 구조에서 CVD-Si을 po-lycrystalline-Si으로 증착한 시편이 amorphous-Si을 증착한 시편보다 산화막 불량이 적다 WSi2 를 증착시킨 WSi2/CVD-Si/SiO2./Si-substrate의 구조에서 CVD-Si의 polycrystalline-Si 혹든 amorphous-Si 의 막 증착에 따른 thin oxide의 불량율 차이는 미미하다 산화막 불량은 CVD-Si에 확산시킨 인(P) 증가 즉 면저항(sheet resistance) 감소로 증가한다. Thin oxide의 절연특성은 WSi2 증착으로 저하된다 WSi2 증착으로 산화막 두께는 증가하나 막 특성은 열등해져 산화막 절연성이 떨어진다.

• Membrane Journal
• /
• v.14 no.4
• /
• pp.312-319
• /
• 2004

The porous SiO$_2$-B$_2$O$_3$ membrane was prepared from Si(OC$_2$$H_5$)$_4$-($CH_3$O)$_3$B-C$_2$$H_5$OH-$H_2O$ system by sol-gel method. In order to investigate the characteristics of this membrane, we examined that using BET, IR spectrophotometer, X-ray diffractometer, SEM and TEM. At $700^{\circ}C$, the surface area of SiO$_2$-B$_2$O$_3$ membrane was 354.398 $m^2$/, the median pore diameter was 0.0048 ${\mu}{\textrm}{m}$, and the particle size of SiO$_2$-B$_2$O$_3$ membrane was 7 nm. The separation properties of the gas mixture ($H_2$/$N_2$) through the SiO$_2$-B$_2$O$_3$ membrane was studied as a function of pressure. The real separation factor($\alpha$) of SiO$_2$-B$_2$O$_3$ membrane for $H_2$/$N_2$ gas mixture was 4.68 at 155.15 cmHg and $25^{\circ}C$. The real separation factor($\alpha$), head separation factor($\beta$) and tail separation factor((equation omitted)) were increased as the pressure of permeation cell increased.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.665-672
• /
• 1997

We applied mechanical alloying process by ball milling to produce molybdenum silicides $MoSi_2$ and $Mo_5Si_3$ using a mixture of elemental molybdenum and silicon powders at room temperature. The intermetallic compound MoSi$_3$ have been obtained by ball milling of $Mo_{33}Si_{67}$ mixture powders for 100 h, which is transformed to single $MoSi_2$ phase by subsequent heat treatment up to $725^{\circ}C$. The grain size of the $MoSi_2$ powders thus obtained was 19 nm, being approximately four times smaller than that of the commercial alloy. The intermetallic compound $MoSi_2$ with grain size of 30 nm have been also obtained by ball milling of $Mo_{62}Si_{38}$ mixture powders for 500 h, which is transformed to single $MoSi_2$ phase by heating up to $1000^{\circ}C$. We believe that the retarded ball milling time for the formation of $MoSi_2$ phase is attributed to its complicated crystal structure and large unit cell. The finer grain size in the ball-milled molybdenum silicides powders is expected to improve room-temperature mechanical properties for high-temperature structural materials.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1493-1498
• /
• 2007

Silicon Nitride ($Si_3N_4$), which is widely used in a variety of applications, is hard-to-machine due to its high hardness. At high temperature (e.g. above $1000^{\circ}C$), however, the machinability can be greatly improved. In this work, we used a $CO_2$ laser with a high absorptivity to $Si_3N_4$ of 0.9 to preheat the surface of a rothting $Si_3N_4$ rod. Preheating and turning of $Si_3N_4$ was executed at the same time. The result of machining was MRR of $8.0mm^3/s$ that is four times faster than normal grinding. Continuous chip formation was observed by a microscope.

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.223-231
• /
• 1992

CaO and ZnO were added to Al2O3-SiO2 binary system respectively as flux, then ZrO2 and TiO2 were applied as nucleating agent to these CaO-Al2O3-SiO2 and ZnO-Al2O3-SiO2 ternary system glass. The transparency could not be kept in CaO-Al2O3-SiO2 system glass, whereas the transparent glass-ceramics were prepared in ZnO-Al2O3-SiO2 system glass containing ZrO2 as the nucleating agent. At this time the optimum heating temperatures for the nucleation and the crystal growth were 78$0^{\circ}C$ and 97$0^{\circ}C$. The sizes of the precipitated crystals in the transparent glass-ceramics were below 0.1 ${\mu}{\textrm}{m}$, and their light transmissibilities were more than 80%.