Using the results analyzed by FEM(Finite Element Method). the microheaters with the stress-balanced $Si_3N_4$(150 nm)/$SiO_2$(300 nm)/$Si_3N_4$(150 nm) diaphragms were fabricated by silicon micromachining techniques. Pt was used as microheater materials. Pt temperature sensor was fabricated to measure the temperature of microheaters. Resistance of temperature sensor and power dissipation of microheater were measured and calculated at the various temperatures. The thermal distribution of heater was examined by a IR thermoviewer. Measured and simulated results are compared and analyzed. The temperature coefficient of resistance of heater was about $0.00379/^{\circ}C$. Pt heater showed the power dissipation of about 51 mW at $300^{\circ}C$ and a uniform thermal distribution on the surface.
Journal of the Korean Crystal Growth and Crystal Technology
/
v.7
no.2
/
pp.207-215
/
1997
Aluminum (Al) thin films were deposited on the Si(100) and TiN(60 nm)/Si (100) substrate by the ionized cluster beam deposition (ICBD) method. The characteristics of thin films were examined by the $\alpha$-step, four-point-probe, Scanning Electron Spectroscopy (SEM), Auger Electron Spectroscopy (AES). The growth rate of the Al thin film increased and the resistivity decreased as the crucible temperature increased. At the crucible temperature $1800^{\circ}C$, the microstructure of Al thin film deposited was smooth and continuous the resistivity decreased as the acceleration voltage increased. Also, the minimum resistivity in Si(100) substrate and TiN(60 nm)/Si(100) substrate were 3.4 $\mu \Omega \textrm {cm}$, 3.6 $\mu \Omega \textrm {cm}$ at the acceleration voltage 4 kV and 2 kV respectively. From the AES spectrumt 14 wasn't detected any impurities In the Al thin film. Therefore the resistivity of Al thin film was affected by the microstructure of film.
Journal of the Korean institute of surface engineering
/
v.56
no.5
/
pp.335-340
/
2023
Quinary component of 3㎛ thick Ti-Al-Si-Cu-N films were deposited onto WC-Co and Si wafer substrates by using an arc ion plating(AIP) system. In this study, the influence of copper(Cu) contents on the mechanical properties and microstructure of the films were investigated. The hardness of the films with 3.1 at.% Cu addition exhibited the hardness value of above 42 GPa due to the microstructural change as well as the solid-solution hardening. The instrumental analyses revealed that the deposited film with Cu content of 3.1 at.% was a nano-composites with nano-sized crystallites (5-7 nm in dia.) and a thin layer of amorphous Si3N4 phase.
Proceedings of the Materials Research Society of Korea Conference
/
2009.05a
/
pp.28.2-28.2
/
2009
군사적, 산업적 용도로 널리 활용되고 있는 적외선 검출기는 InSb, HgCdTe(MCT)와 같은 물질들을 감지 소자로 사용하고 있다. 현재 가장 많이 사용되는 MCT는 적외선의 전 영역을 감지할 수 있는 장점이 있지만, 대면적 제작이 어려운 단점이 있다. 이에 비해 InSb는 안정적인 재료의 특성, 높은 전하이동도($1.2\times10^6\;cm^2/Vs$) 그리고 대면적 소자 제작의 가능성 등이 높게 평가되어 차세대 적외선 검출소자로 각광 받고 있다. InSb 적외선 수광 소자는 1970년대부터 미국을 중심으로 이온주입, MOCVD 또는 MBE와 같은 다양한 공정을 이용하여 제작되어 왔으며, 앞으로도 군수용 제품을 비롯하여 산업전반에서 더욱 각광을 받을 것으로 예상된다. 하지만 InSb는 77 K에서 0.225 eV의 상대적으로 작은 밴드갭을 갖고 있기 때문에 누설전류로 인한 성능저하가 고질적인 문제로 대두되었고, 이를 해결하기 위한 고품질 절연막 연구가 InSb 적외선 수광 소자 연구의 주요 이슈 중 하나가 되어왔다. PECVD, photo-CVD, anodic oxidation 등의 공정을 이용하여 $SiO_2$, $Si_3N_4$, 양극산화막(anodic oxide) 등 다양한 물질들에 대한 연구가 진행되었고[1,2], 산화막과 반도체 계면에서의 열확산을 억제하여 계면트랩밀도를 최소화하기 위한 연구도 활발히 이루어졌다[3]. 하지만 InSb 소자의 성능개선을 위한 최적화된 산화막에 대한 연구는 여전히 불충분한 실정이다. 본 연구에서는 n형 (100) InSb 기판 (n = 0.2 ~ $0.85\times10^{15}cm^{-3}$ @ 77 K)을 이용하여 양극산화막, $SiO_2$, $Si_3N_4$ 등을 증착하고 절연막으로서 이들의 특성을 비교 분석하였다. 양극산화막은 상온에서 1 N KOH 용액을 이용하여 양극산화법으로 증착하였으며, $SiO_2$, $Si_3N_4$는 PECVD로 $150^{\circ}C$에서 $300^{\circ}C$까지 온도를 변화시켜가며 증착하였다. SEM분석과 XPS분석으로 두께의 균일도와 절연막의 조성, 계면확산 정도를 확인하였으며, I-V와 C-V 커브측정을 통해 각 절연막의 전기적 특성을 평가하였다. 이 분석들을 통해 각각의 공정 조건에 따른 절연막의 상태를 전기적 특성과 관련지어 설명할 수 있었다.
Journal of the Korean Institute of Telematics and Electronics A
/
v.29A
no.4
/
pp.22-27
/
1992
The cyclic voltammogram characteristics at the magnetized SrO${\cdot}6Fe_{2}O_{3}$ ceramics/(($10^{-3}$M KCI + p-Si powders) and /(($10^{-4}$M CsNO$_3$ + n-GaAs powders) suspension interfaces have been studied using the microelectrophoresis and the cyclic voltammetric method. The negatively charged ions are specifically absorbed on the virgin and the magnetized SrO${\cdot}6Fe_{2}O_{3}$ ceramics surfaces. The zeta potentials of the p-Si and n-GaAs colloidal semiconductors are + 41mV and -44.8mV, respectively. The magnetization effects act as potential barriers at the magnetized SrO${\cdot}6Fe_{2}O_{3}$ interfaces. The positivelely charged p-Si and the negatively charged n-GaAs colloidal semiconductors act as potential barriers at the virgin SrO${\cdot}6Fe_{2}O_{3}$ interfaces. On the other hand, the charged p-Si and n-GaAs colloidal semiconductors act as potential barrier scavengers at the magnetized SrO${\cdot}6Fe_{2}O_{3}$ interfaces. The magnetization effects and the charged colloidal semiconductor effects are irreversible and interdependent.
The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
/
v.11
no.3
/
pp.117-123
/
2006
The water quality before and after a typhoon was investigated as a part of a study on the increase of organic matter and on the fundamental measures to counter chemical oxygen demand (COD) in the eutrophic Soho coastal seawaters of Gamak Bay. The dissolved oxygen (DO) saturations were <54% when water column was stratified. The DO saturation was similar at surface and in the bottom layer after a typhoon $(78\sim88%)$, and a very high DO saturation (234%) was observed in the surface water after mass phytoplankton growth. The highest values of $NH_4-N,\;NO_3-N,\;PO_4-P$, and $SiO_2-Si$ were 18.22, 38.90, 1.58, and $52.10{\mu}M$, respectively, when freshwater entered after heavy rainfall events. In addition, high concentrations of $NH_4-N,\;PO_4-P$, and $SiO_2-Si$ were detected with low DO saturations in bottom water (>5m). A maximum chlorophyll (Chl.) concentration of $311.0{\mu}gl^{-1}$ was observed after typhoon, when a high-density Scrippsiella trochoidea red tide occurred with cell density of 42,000 cells $ml^{-1}$. The algal growth potential (AGP) was high after the typhoon. Nitrogen was always a limiting nutrient for phytoplankton growth. The highest COD level was $10.55mgl^{-1}$, and the main reason of the variation in COD was likely to be phytoplankton growth $(r^2=0.612,\;p=0.000)$. Organic matter, which entered the water column when the typhoon stirred the sediments, seems to have little effects on COD increase.
In this study, as Cu diffusion barrier, tantalum nitrides were successfully deposited on Si(100) substrate and $SiO_2$ by plasma assisted atomic layer deposition(PAALD) and thermal ALD, using pentakis (ethylmethlyamino) tantalum (PEMAT) and NH$_3$ as precursors. The TaN films were deposited at $250^{\circ}C$ by both method. The growth rates of TaN films were 0.8${\AA}$/cycle for PAALD and 0.75${\AA}$/cycle for thermal ALD. TaN films by PAALD showed good surface morphology and excellent step coverage for the trench with an aspect ratio of h/w -1.8:0.12 mm but TaN films by thermal ALD showed bad step coverage for the same trench. The density for PAALD TaN was 11g/cmand one for thermal ALD TaN was 8.3g/$cm^3$. TaN films had 3 atomic % carbon impurity and 4 atomic % oxygen impurity for PAALD and 12 atomic % carbon impurity and 9 atomic % oxygen impurity for thermal ALD. The barrier failure for Cu(200 nm)/TaN(10 nm)/$SiO_2$(85 nm)/ Si structure was shown at temperature above $700^{\circ}C$ by XRD, Cu etch pit analysis.
It is believed that fly ash could be suitable for preparing the sialon by carbothermal reduction method because the total amount of SiO2 and Al2O3 is above 80% and the unburned residual carbon is above 5% within the fly ash. The effects of reaction temperature (1350, 1400, 145$0^{\circ}C$) reaction time (1, 5, 10 hours) and the amount of carbon additions (C/SiO2=2, 3, 4 mole) on the $\beta$-sialon synthesis were obserbed, It was conformed that $\beta$-sialon (Z=2.15~2.18) was formed as major phase under all of the synthesis conditions and small amount of Si2ON2 SiC, AlN and Si3N4 was formed depending on the synthesis conditions. FeSix intermetal-lic compound was formed above 140$0^{\circ}C$ reaction temperature due to the large amount of iron oxides within the raw fly ash.
Kim, Yeong-Uk;Kim, Yeong-Uk;Go, Jong-U;Lee, Nae-In;Kim, Il-Gwon;Park, Sun-O;An, Seong-Tae;Lee, Mun-Yong;Lee, Jong-Gil
Korean Journal of Materials Research
/
v.3
no.1
/
pp.12-18
/
1993
Abstract The effect of the film stress on the thermal stability of TiSi, films under the dielectric overcoat was investigated. TiS$i_2$ films with the sheet resistance of 1.2 ohm/sq. were produced by a solid-state reaction between sputtered Ti film and single-crystalline Si in an RTA (rapid thermal anneal) machine. Dielectric overcoats such as the USG (Undoped Silicate Glass, Si$O_2$) film and the PE-SiN(S$i_3$$N_4$) film were deposited by AP-CVD and PE-CVD, respectively, on the TiS$i_2$ film. The thermal stability of the TiSi, film was evaluated by changes in the sheet resistance, film stress and microstructure after furnace anneals at 90$0^{\circ}C$. Agglomeration of the TiSi2 film high temperatures results in the increase of sheet resistance and the decrease of tensile stress of TiSi, film. The stress level of the TiSi" PE-SiN and ~SG films at 90$0^{\circ}C$C was 1.3${\times}{10^{9}}$, 1.25 ${\times}{10^{10}}$, 2.26 ${\times}{10^{10}}$ dyne/c$m^2$ in tensile, respectively. Dielectric films deposited by CVD on TiSi, was effective on preventing agglomeration of TiSi,. The PE-SiN film mproved the thermal stability of TiSi, more effectively than the AP-CVD USG film. It is considered that agglomeration of the TiS$i_2$ film under the stress of dielectric overcoat at high temperature can be caused by a diffusional flow of atom called Nabarro-Herring microcreep.reep.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.