• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.29-33
• /
• 2001

In the present study, AZ91Mg/$\textrm{Al}_2\textrm{O}_3$ short fiber+SiC particulates hybrid metal matrix composites(MMCs) were fabricated by squeeze casting method. Different particulate sizes of 45, 29 and $9\mu\textrm{m}$ were hybridized with 5% volume fraction to investigate the effect of SiC particulates size on microstructure, mechanical and thermal properties such as hardness, flexural strength, wear resistance and thermal expansion. Results show that the microstructure of the hybrid composites were quite satisfactory, namely revealing relatively uniform distribution of reinforcements. Some aggregation of SiC particulates caused by particle pushing was observed especially in the hybrid composites containing in fine particulates($9\mu\textrm{m}$). The hardness and flexural strength were improved by decreasing particulates size, whereas wear resistance improved by increasing particulates size because of large particulates restricting matrix wear from contacted stress. Regardless of particulates size, thermal expansion of composites was the same. This may be because the content of particulates was in all cases 5 volume fraction.1

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.157-161
• /
• 2000

In order to investigate the substrate effect on the electrochemical properties of thin-film electrode, $LiCoO_2$ was deposited onto the alumina, chemically etched-Si and flat-Si substrates. After annealing at $800^{\circ}C$ in $O_2$ for 30min, the film deposited on the alumina consisted of large particles with several cracks, whereas the film deposited on the flat-Si substrate was composed of very small and uniform particles. The films deposited on the flat-Si showed improved electrochemical properties such as peak potential divergence and rate-capability, over those deposited on the alumina and chemically etched-Si substrate, which can be attributed to the differences of the particle size surface morphology, and the electrical resistance of the current collector.

• Korean Journal of Materials Research
• /
• v.19 no.4
• /
• pp.212-219
• /
• 2009

A study on the dry beneficiation of sericite occurring in the Daehyun Mine of the Republic of Korea region as performed by applying selective grinding and air classification techniques. Quartz and sericite occurred in the raw ore as major components. The results of liberation using a ball mill and an impact mill showed that the contents of $R_2O$ were increased while $SiO_2$ was decreased in proportion to decreasing particle size. According to the XRD, XRF analysis and the EDS of SEM analysis, the ball mill gave a better grade product in $R_2O$ content than the impact mill when the particle size was the same. When the raw ore was ground by the impact mill with arotor speed 57.6 m/sec and then followed by 15,000rpm classification using an air classifier, the chemical composition of the over flowed product was 49.65wt% $SiO_2$, 32.15wt% $Al_2O_3$, 0.13wt% $Fe_2O_3$, 10.37wt% $K_2O$, and 0.14wt% $Na_2O$. This result indicates that the $R_2O$ contents were increased by 49.5% compared to that of the raw ore. From these results described above, it is suggested that hard mineral such as Quartz little ground by selective grinding using impact mill whereas soft mineral such as sericite easily ground to small size. As a result of that hard minerals can be easily removed from the finely ground sericite by air classification and the $R_2O$ grade of thus obtained concentrate was improved to higher than 10wt% which can be used for ceramics raw materials.

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.850-855
• /
• 2002

Silica powders were prepared from $SiCl_4$-$H_2$O system by chemical vapor deposition process, and investigated on size control of the products with reaction conditions. The products were amorphous and nearly spherical particles with 130nm~50nm in size. The size distribution became narrow with the increase of [$H_2$O]/[SiCl$_4$] concentration ratio. The particle size decreased with the increase of reaction temperature, [$H_2$O]/[SiCl$_4$] concentration ratio and total flow rate. The specific surface area measured by BET method was about three times larger than that of electron microscope method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.222-223
• /
• 2006

고전압 전기기기의 열화는 여러 가지 요인에 의해 발생한다. 따라서 여러 환경 요인에 영향을 비교적 적게 맡는 절연재료 개발에 의한 절연성능 항상은 그동안 많은 연구자들의 관심의 대상이 되어왔다. 최근 고분자 수지 내에 나노 크기의 충진제를 혼합하여 절연성능 및 기계적, 열적 특성을 향상시키는 연구가 점차 활성화되고 있다. 그러나 나노 크기 입자의 활용은 분자단위 크기의 입자가 가지는 Van der Waals력의 문제로 인하여 전기기기의 절연재료로 활용하기에는 어려운 점이 나타나고 있다. 본 논문에서는 에폭시/$SiO_2$ 나노복합재료를 제조하여 분산시간에 따른 입자의 문산 상태를 살펴보았다.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1314-1316
• /
• 1994

$0.36[wtx]Sio_2$ and $0.1[wtx]H_3BO_3$ were added to strontium ferrite magnets of the magnetoplumbite phase SrO $5.7Fe_2O_3$. This experiment was carried out to investigate the effects of particle size distribution as a function of milling time(20,30,40,50,60,70 hours) on the magnetic properties of SrO $5.7Fe_2O_3$ ferrite magnet. The B-H Curve, density and the degree of orientation were measured. The optimal conditions of making magnets and properties of a typical sample are the following : The milling time was 60 hours. Magnetic and physical properties are $B_r$=4000[G], $_BH_c$=3330[Oe], $_IH_c$=3525[Oe], (BH)max=3.786 [MGOe], density= $5.0063g/cm^2$, orientation factor f=0.813.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.217-224
• /
• 2021

In this study, Monte Carlo (MC) simulation is conducted with recurrence relation to study the effect of SiO₂ with different particle size and their roles in enhancing the ionic conductivity and lithium transference number of PMMA composite polymer electrolytes (CPEs). The MC simulated ionic conductivity is verified with the measurements from Electrochemical Impedance Spectroscopy (EIS). Then, the lithium transference number of CPEs is calculated using recurrence relation with the MC simulated current density and the reference transference number obtained. Incorporation of micron-size SiO₂ (≤10 ㎛) fillers into the mixture improves the ionic conductivity from 8.60×10^-5 S/cm to 2.35×10^-4 S/cm. The improvement is also observed on the lithium transference number, where it increases from 0.088 to 0.3757. Furthermore, the addition of nano-sized SiO₂ (≤12 nm) fillers further increases the ionic conductivity up towards 3.79×10^-4 S/cm and lithium transference number of 0.4105. The large effective surface area of SiO₂ fillers is responsible for the improvement in ionic conductivity and the transference number in PMMA composite polymer electrolytes.

• Journal of the Korean Ceramic Society
• /
• v.52 no.6
• /
• pp.455-461
• /
• 2015

Porous ceramics with tailored pore size and shape are promising materials for the realization of a number of functional and structural properties. A novel method has been reported for the investigation of the role of SiC in the formation of $SiO_2$ foams by colloidal wet processing. Within a suitable pH range of 9.9 ~ 10.5 $SiO_2$, particles were partially hydrophobized using hexylamine as an amphiphile. Different mole ratios of the SiC solution were added to the surface modified $SiO_2$ suspension. The contact angle was found to be around $73^{\circ}$, with an adsorption free energy $6.8{\times}10^{-12}J$. The Laplace pressure of about 1.25 ~ 1.6 mPa was found to correspond to a wet foam stability of about 80 ~ 85%. The mechanical and thermal properties were analyzed for the sintered ceramics, with the highest compressive load observed at the mole ratio of 1:1.75. Hertzian indentations are used to evaluate the damage behavior under constrained loading conditions of $SiO_2$-SiC porous ceramics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.176-176
• /
• 2009

Influences of dose and particle size of $Al_2O_3$ filler and sintering time on the dielectric properties of $Al_2O_3$ filler/CaO-$Al_2O_3-SiO_2$ (CAS) glass composites were investigated with a view to applying the composites to the substrate material in low temperature co-firing ceramic (LTCC) technology. The increased addition of $Al_2O_3$ filler with the particle size of 1 ${\mu}m$ monotonically decreased the density of the sintered specimen at a given temperature, while sintering of the 10 wt% $Al_2O_3$ added specimen at $925^{\circ}C$ for 2 h demonstrated 96.0 % of the relative density, dielectric constant of 6.34, and quality factor of 2,760 GHz. As for the influence of the particle size of the $Al_2O_3$ filler, there existed an optimum particle size (30 ${\mu}m$) to ensure successful densification (96.5 %) of the 10 wt% $Al_2O_3$/CAS composites at $925^{\circ}C$ for 2 h, at which condition the specimen demonstrated dielectric constant of 5.45 and quality factor of 3,740 GHz. When the influence of the sintering time of the 10 wt% $Al_2O_3$) (30 ${\mu}m$) added specimen was investigated at the sintering temperature of $925^{\circ}C$, an overly long sintering time degraded dielectric properties due to the over-sintering and the significant growth of the second phase such as anorthite, while the sintering for 4 h demonstrated 96.58 % of the relative density, dielectric constant of 5.4, and quality factor of 4,050 GHz. These results demonstrate the feasibility of the investigated material as the substrate material in LTCC technology.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.5
• /
• pp.673-679
• /
• 2004

Particle breakthrough can occur by either the breakoff of previously captured particles (or flocs) or the direct passage of some influent particles through the filter. Filtration experiments were performed in a laboratory-scale filter using spherical glass beads with a diameter of 0.55 mm as collectors. A single type of particle suspension (Min-U-Sil 5, nearly pure $SiO_2$) and three different destabilization methods (pH control, alum and polymer destabilization) were utilized. The operating conditions were similar to those of standard media filtration practice: a filtration velocity of 5 m/h. To assess the possibility of particle detachment during the normal filtration, a hydraulic shock load (20% increase of flow rate) was applied after 4 hours of normal filtration. The magnitude of particle detachment was proportional to the particle size for non-Brownian particles. At the same time, less favorable particles, i.e., particles with larger surface charge, were easily detached during the hydraulic shock load. Therefore, proper particle destabilization before filtration is crucial for maximum particle removal as well as minimum particle breakthrough.