• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.24-27
• /
• 2000

Ferroelectric P $b_{0.99}$〔(Z $r_{0.6}$S $n_{0.4}$)$_{0.9}$ $Ti_{0.1}$〕$_{0.98}$N $b_{0.02}$ $O_3$(PNZST) thin films were deposited by a RF magnetron sputtering on (L $a_{0.5}$S $r_{0.5}$)Co $O_3$(LSCO)/Pt/Ti/ $SiO_2$/Si substrate using a PNZST target with excess PbO of 10 mole％. The thin films deposited at the substrate temperature of 500 $^{\circ}C$ were crystallized to a perovskite phase after rapid thermal annealing(RTA) The thin films annealed at 650 $^{\circ}C$ for 10 seconds in air exhibited the good crystal structures and ferroelectric properties. The remanent polarization and coercive field of the PNZST capacitor were about 20 $\mu$C/$\textrm{cm}^2$ and 50 kV/cm, respectively. The reduction of the polarization after 2.2$\times$10$^{9}$ switching cycles was less than 10 ％.0 ％.％.0 ％.0 ％.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.174-174
• /
• 2009

현재 전자부품용으로 사용되는 유리프리트의 경우 PbO계를 주로 사용하고 있다. 최근 환경규제에 따른 PbO 사용이 제한됨에 따라 이를 대체할 Pb-free 유리 조성에 대한 연구가 활발히 진행 중이다. Pb-free계로서는 $Bi_2O_3$계, $B_2O_3$계가 주로 연구되고 있으나 소성 온도가 $500^{\circ}C$이상으로 높고 또한 $Bi_2O_3$ 계는 중금속이기 때문에 문제가 있다. 본 연구에서는 $400^{\circ}C$ 미만 소성이 가능한 SnO-$P_2O_5$계를 기본 조성계로 선택하고 열적, 전기적, 화학적 특성을 개선하기 위해 $R_2O_3$(R=Al, B), RO(R=Mg, Zn, Ca, Ba) 를 첨가하였다. 개선된 조성으로 샘플을 만들고 이를 대상으로 실제 전자부품 생산 공정에 적용 실험을 진행 하였다. 실험에 사용된 전자 부품은 소형 칩 베리스터로 생산 공정에서 코팅용 유리프리트와 파우더를 절연체로서 전면에 코팅하게 된다. 유리프리트를 코팅함으로서 누설 전류를 차단하고 생산 공정시 베리스터 내부를 보호하게 된다. 실험에 사용된 샘플의 열적 특성은 TMA로, 전기적 절연 특성은 고 절연저항 측정기로 측정하였고 내 산성과 내 알칼리성도 측정하였다. 샘플을 이용하여 완성된 칩 베리스터의 성능은 고온, 내습 신뢰성 TEST(고온:$150^{\circ}C$ 12HR, 내습:$85^{\circ}C$-85%12HR)로 실험하여 합부판정 (Leakage current <10uA)을 내려 완성품과 불량품을 가려내었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.418-427
• /
• 1997

The effect of $La_2O_3$ as a dopant on the microstructure structure, crystal structure and electrical properties was studied. $0.05Pb(Sn_{0.5}Sb_{0.5})O_3＋0.11PbTiO_3＋0.84PbZroO_3＋0.4Wt%MnO_2$ (=0.05PSS ＋0.11PT＋0.84PZ+0.4wt%$MnO_2$) systems doped with 0, 0.1, 0.3, 0.5, 0.7, 1, 3, 5 mole% $La_2O_3$ were fabricated and investigated sintering density, crystal structure and micro-structure. The sintered 0.05PSS＋0.11PT＋0.84PZ+0.4wt%$MnO_2$ system doped with $La_2O_3$showed sintering density of the range of 7.683 g/㎤ of 0 mole% doping to 7.815 g/㎤ of 0 mole% doping. The average grain sizes in the range of 0 to 5 mole% $La_2O_3$were decreased from 9.0 $\mu\textrm{m}$ to 1.3 $\mu\textrm{m}$. X-ray diffraction investigation of sintered bodies showed that solid solutions were formed between 0.05PSS＋0.11PT＋0.84PZ+0.4wt%$MnO_2$ system and $La_2O_3$ in the range of 0 to 1 mole% but second phases were formed in case of 3, 5 mole%. Dielectric constants at 1 kHz were increased with 0 to 3 mlole% $La_2O_3$ before and after poling at the condition of 5 $KV_{DC}$/mm at $120^{\circ}C$ or $140^{\circ}C$ during 20 minutes. All Dielectric losses at 1 kHz were less than 1%, Curie temperatures were $208^{\circ}C$, $183^{\circ}C$, $152^{\circ}C$ and $127^{\circ}C$ at 0, 0.5, 1, 3 mole% $La_2O_3$ respectively. The values of $K_p$ were increased from 0 to 3 mole% $La_2O_3$ after poling at condition of 5 $KV_{DC}$mm at the condition of $120^{\circ}C$ or $140^{\circ}C$. The case of 0.7 mole% $La_2O_3$doped 0.05PSS＋0.11PT＋0.84PZ+0.4wt%$MnO_2$ system showed $K_p$ of 14.5% by poling at $140^{\circ}C$ during 20 minutes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.389-389
• /
• 2011

Transparent conductive oxide (TCO) 박막은 디스플레이 및 태양전지 등 광범위한 분야에서 적용되고 있으며, 특히 indium tin oxide (ITO)는 낮은 전기적 저항과 우수한 광투과도를 가지고 있어서 이미 많은 분야에 적용되고 있다. 본 연구는 RF와 DC를 혼용한 마그네트론 스퍼터링 공정을 활용하여 ITO 박막 특성 및 이를 활용한 유기태양전지 적용에 관한 것이다. UV-O3 처리된 glass 기판위에 thermal evaporation 방식으로 밀착력을 높이기 위하여 Cr을 5 nm 두께로 증착한 후 Al을 95 nm 증착하였다. 그 위에 스퍼터링 공정으로 ITO 박막을 In2O3:SnO2 target (10wt% SnO2)을 사용하여 1.0 mTorr의 공정압력(Ar:O2=30:1), 50W의 RF power 및 0.11kW의 DC power에서 50~250 nm의 두께로 증착하였다. ITO 박막의 결정구조 및 표면 형상은 x-ray diffraction (XRD) 및 scanning electron microscope (SEM)을 사용하여 분석하였으며, 전기적 특성은 four-point probe법으로 비저항값을 측정하였다. 또한 높은 광변환효율을 가지는 태양전지 제작을 위하여, 다양한 두께의 ITO 박막을 사용하여 ITO/ZnO/P3HT:PCBM/PEDOT/Ag 구조의 유기태양전지를 제작하여 소자 특성을 최적화 하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.33.1-33.1
• /
• 2009

Lead-free (1-x)$(Na_{0.5}K_{0.5})NbO_3$-xBa($Ti_{0.9}Sn_{0.1})O_3$ [NKN-BTS-100x] ceramics doped with 1 mol% $MnO_2$ have been prepared by the conventional solid state method and their structural and piezoelectric properties were investigated. The NKN-BTS-100x ceramics exhibited a dense and homogeneous microstructure when they were sintered at $1030-1150^{\circ}C$. Grain growth was observed for the specimen sintered at relatively low temperature of $1050^{\circ}C$. A tetragonal/orthorhombic morphotropic phase boundary (MPB) in the perovskite structure was also appeared for the NKN-BTS-100x ceramics (0.04$1050^{\circ}C$. The enhanced piezoelectric properties in the NKN-BTS ceramics with a MPB composition were obtained. Especially, for the NKN-BTS-6 ceramics, a high dielectric constant (${\varepsilon}^T_3/\varepsilon_0=1,400$), piezoelectric constant ($d_{33}=237$) and electromechanical coupling factor ($k_p=0.42$) were obtained.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.2
• /
• pp.65.2-66
• /
• 2021

Observational studies of supernova (SN) feedback are limited. In our galaxy, most supernova remnants (SNRs) are located in the Galactic plane, so there is contamination from foreground/background sources. SNRs located in other galaxies are too far, so we cannot study them in detail. The Large Magellanic Cloud (LMC) is a unique place to study the SN feedback due to their proximity, which makes possible to study the structure of individual SNRs in some detail together with their environment. Recently, we carried out a systematic study of 13 LMC SNRs using [P II] (1.189 ㎛) and [Fe II] (1.257 ㎛) narrowband imaging with SIRIUS/IRSF, four SNRs (SN 1987A, N158A, N157B and N206), show [P II]/[Fe II] ratio much higher than the cosmic abundance. While the high ratio of SN 1987A could be due to enhanced abundance in SN ejecta, we do not have a clear explanation for the other cases. We investigate the [P II] knots found in SNRs N206, N157B and N158A, using optical spectra obtained last November with GMOS-S mounted on Gemini-South telescope. We detected several emission lines (e.g., H I, [O I], He I, [O III], [N II] and [S II]) that are present in all three SNRs, among other lines that are only found in some of them (e.g., [Ne III], [Fe III] and [Fe II]). Various line ratios are measured from the three SNRs, which indicate that the ratios of N157B tend to differ from those of other two SNRs. We will use the abundances of He and N (from the detection of [N II] and He I emission lines), together with velocity measurements to tell whether the origin of the [P II] knots are SN ejecta or CSM/ISM. For this purpose we have built a family of radiative shock with self-consistent pre-ionization using MAPPINGS 5.1.18, with shock velocities in the range of 100 to 475 km/s. We will compare the observed and modeled line fluxes for different depletion factors.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.5
• /
• pp.573-576
• /
• 1999

The rate constants and kinetic solvent isotope effects (KSIE, KMeOH/kMeOD) for solvolyses of para-substituted phenylchloroformates in CH3OH, CH3OD, H2O, D2O, 50% D2O-CH3OD were determined at 15.0 and 25.0℃ using conductometric method. Kinetic solvent isotope effects for the solvolyses of para-substituted phenyl chloroformates were 2.39-2.51, 2.21-2.28, and 1.67-1.69 for methanol, 50% aqueous methanol, and water, respectively. The slopes of Hammett plot for solvolysis of para-substituted phenyl chloroformates in methanol, 50% aqueous methanol, and water were 1.49, 1.17 and 0.89, respectively. The Hammett type plot of KSIE, log (KSIE) versus p, can be a useful mechanistic tool for solvolytic reactions. The slopes of such straight lines for para-substituted phenyl chloroformates are almost zero in methanol, 50% aqueous methanol, and water. It was shown that the reaction proceeds via an associative SN2 and/or general base catalysis addition-elimination (SAN) mechanism based on activation parameters, Hammett p values, and slopes of Hammett type plot of KS-IE.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.343-348
• /
• 2003

Indium tin oxide (ITO) thin films (170 nm) were grown by DC magnetron sputtering deposition on Coming glass substrates without a post annealing. The electrical transport and optical properties of the films have been investigated as a function of deposition temperature $T_{s}$ (10$0^{\circ}C$$\leq$ $T_{s}$$\leq$35$0^{\circ}C$) and oxygen partial pressure $P_{o_{2}}$, (0 $P_{o_{2}}$ $\leq$ 10$^{-5}$ torr). Films were deposited from a high density (99% of theoretical density) ITO target (I $n_2$ $O_3$: Sn $O_2$= 90 wt% : 10 wt%) made of ITO nano powders. With an increase of $T_{s}$ the electrical resistivity p of ITO thin films was found to decrease, but the mobility $\mu$$_{H}$ was found to increase. The carrier density nu shows the maximum value of 6.6$\times$10$^{20}$ /㎤ at $T_{s}$ = 30$0^{\circ}C$. At fixed Is, with an increase of the oxygen partial pressure, $n_{H}$ and $\mu$$_{H}$ were found to decrease, but p was found to increase. The minimum resistivity and maximum mobility values of the ITO films were found to be 0.3 mΩ.cm and 39.3 $\textrm{cm}^2$/V.s, respectively. The visible transmittance of the ITO films was above 80%.. 80%..

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.7
• /
• pp.473-478
• /
• 2001

Ferroelectric P $b_{0.99}$［(Z $r_{0}$ 6S $n_{0.4}$)/0.9/ $Ti_{0.1}$］0.98/N $b_{0.02}$ $O_3$(PNZST) thin films were deposited by a RF magnetron sputtering on L $a_{0.5}$S $r_{0.5}$Co $O_3$(LSCO)/Pt/Ti/ $SiO_2$/Si substrate using a PNZST target with excess PbO of 10 mole%. The crystallinity and electrical properties of the thin films annealed at various temperature and time were investigated. The thin films deposited at the substrate temperature of 500 $^{\circ}C$ and the power of 80 W were crystallized to a perovskite phase after rapid thermal annealing(RTA). The thin films annealed at 650 $^{\circ}C$ for 10 seconds in air exhibited the good crystal structures. The remanent polarization and coercive field of the PNZST capacitor were about 20 $\mu$C/$\textrm{cm}^2$ and 50 kV/cm, respectively. The reduction of the polarization after 2.2$\times$10$^{9}$ switching cycles was less than 10 %..10 %......

• Textile Coloration and Finishing
• /
• v.18 no.5 s.90
• /
• pp.22-29
• /
• 2006

The purpose of this study was to investigate the dyeability and antibacterial activity on wool fabric dyed with cochineal at variable dyeing conditions. Al, Cr, Fe, Cu and Sn were used as mordants and adsorption was compared with different mordanting methods. The optimum dyeing conditions of wool fabrics were dyeing concentration 2.0%(o.w.s), dyeing temperature $60^{\circ}C$, pH 3 and dyeing time 30 minutes. The pre-mordanting method was preferred for Al and Cr, and the post-mordanting one was preferred for Cu, Sn and Fe to achieve better dyeing. The optimum mordanting conditions of wool fabrics dyed with cochineal were mordanting concentration of 1%(o.w.s), mordanting temperature $60^{\circ}C$, and dyeing time 30 minutes. Wool fabrics dyed with cochineal showed a little antibacterial activity, but it was increased by Cu and Sn mordanting. The light fastness and perspiration fastness of wool fabric treated with cochineal were improved by mordanting.