• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1135-1139
• /
• 2000

본 연구에서는 Pt/Sn $O_2$박막의 CO 감지특성을 향상시키기 위하여 표면 형상을 제어하였다. Pt/Sn $O_2$계 박막센서의 최적 동작온도는 175$^{\circ}C$이었다. Pt가 12초 동안 증착된 Sn $O_2$가 200ppm의 CO 가스에 대하여 1.23의 최대감도를 나타내었고, 그 이상의 Pt 증착시간 증가에 따라 Sn $O_2$위의 Pt의 coverage가 증가하여 센서의 감도를 감소시켰다. 다층박막(multi-layer thin film)의 단층의 Pt/Sn $O_2$복합체 위에 다시 Sn $O_2$및 Pt의 cluster 층들을 연속적으로 증착함으로서 제작되었다. 단지 하나의 Pt 층만을 증착한 Sn $O_2$막보다 다층의 Pt/Sn $O_2$막이 더욱 우수한 감도( $R_{air}$/ $R_{co}$=1.72, CO: 200 ppm)를 나타내었다. Pt/Sn $O_2$다층박막의 우수한 감도의 원인은 Pt와 Sn $O_2$사이의 계면적 증대 때문인 것으로 생각되어 진다.다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.160-161
• /
• 2008

$SnO_2$는 n형 반도체로써 3.6 eV의 큰 밴드갭을 가지는 물질로 CO와 NOx 가스에 좋은 감도를 나타내는 것으로 보고되고 있다. 문헌에 따른 일반적인 $SnO_2$ 가스센서는 후막이나 벌크형태로 제작되었다. 근래에는 가스감응체가 $SnO_2$ 나노선 형태인 가스센서가 활발한 연구 중에 있다. 본 논문에서는 기판 위에 서로 분리된 전극 패턴에 Au를 촉매로 하여 네트워크 구조로 된 $SnO_2$ 나노선이 합성되었다. 제작된 가스센서에 Pd 도핑에 따른 영향을 알아보기 위하여 1.8 mM의 Pd 용액 ($PdCl_2{\cdot}xH_2O$ 3 mg + $H_2O$ 10 ml)을 이용하여 센서에 도핑하였다. 측정 시스템에서 $NO_2$ 가스에 대한 센서의 특성을 분석한 결과 도핑하지 않은 $SnO_2$ 센서보다 20%정도의 감도가 개선되었다.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.193-198
• /
• 2008

A novel refractive index sensor, which consists of polymer channel waveguide overlaid with $TiO_2$ thin film, is demonstrated. To evaluate the fabricated sensor, we measured the polarimetric interference induced by concentration change of injected glycerol solution. Our experimental results show that thicker $TiO_2$ film improves the sensitivity of the polarimetric interferometer. For the fabricated waveguide with a 20 nm thick $TiO_2$ film, the measured index change to lead phase variation of $2{\pi}$ is $1.8{\times}10^{-3}$.

• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.52-57
• /
• 2023

This study is a basic research for the development of high performance flexible electrode material. To enhance its electrochemical property, CuO nanoparticles (CuO NPs) were introduced and dispersed on surface of CNT fiber through electrochemical deposition method. The CNT fiber/CuO NPs electrode was fabricated and applied to electrochemical non-enzymatic glucose sensor. Surface morphology and elemental composition of the CNT fiber/CuO NPs electrode was characterized by scanning electron microscope (SEM) with energy dispersive X-ray spectrometry (EDS). And its electrochemical characteristics were investigated by cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry. The CNT fiber/CuO NPs electrode exhibited the good sensing performance for glucose detection such as high sensitivity, wide linear range, low detection limit and good selectivity due to synergetic effect of CNT fiber and CuO NPs. Based on the unique property of CNT fiber, CuO NPs were provide large surface area, enhanced electrocatalytic activity, efficient electron transport property. Therefore, it is expected to develop high performance flexible electrode materials using various nanomaterials.

• Fire Science and Engineering
• /
• v.16 no.4
• /
• pp.15-19
• /
• 2002

This dissertation is about the development of $BaTiO_3$-type PTC(Positive Temperature Coefficient) thermistor by composition method. A multilayer-type PTC samples were fabricated under optimal conditions after setting the experimental composition equation as ($Ba_{0.95-x}$S $r_{0.05}$$Ca_{x}$ )$TiO_3$-$0.01TiO_2$-$0.01SiO_2$-$\alpha$$MnCO_3$-$\beta$N $b_2$ $O_{5}$.) and their testing results were analyzed. The optimal sin-tering and cooling temperatures were 13$50^{\circ}C$ for two hours and $100^{\circ}C$/h for an hour, respectively; By composing Ca and Mn, dopants to lower the resistivity at room temperature, and Nb, a dopant to raise peak resistivity(Ca:5 mol%, Mn:0.08 mol%, Nb:0.18 mol%), appropriately, a PTC thermistor, having the characteristics of relatively low resistivity at room temperature and high peak resistivity and a good temperature coefficient, has been developed. And we find that it is possible of application for fire detection sensor.r.r.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.380-385
• /
• 2023

In this study, an MPB PMNT system containing 0.05 to 0.10 wt.% BaTiO₃ was synthesized using a traditional chemical method and its pyroelectricity was investigated. Pyroelectricity, dielectricity, and ferroelectricity of the synthesized BaTiO₃-PMNT system were analyzed by heat treatment at 1240~1280 ℃ for 4 hours to evaluate its applicability as a pyroelectric sensor. Unlike the simple ABO₃ ferroelectric, the BaTiO₃-doped PMNT system exhibited phase transition characteristics over a wide temperature range typical of complex perovskite structures. Although no dramatic change could be confirmed depending on the amount of BaTiO₃ added, stable pyroelectricity was maintained near room temperature and over a wide temperature range. When the amount of BaTiO₃ added increased from 0.05BaTiO₃-PMNT to 0.10BaTiO₃-PMNT, the electric field slightly increased from 5.00×10³ kV/m to 6.75×10³ kV/m, and the maximum value of remanent polarization slightly increased from 0.223 C/m² to 0.234 C/m². The pyroelectric coefficients of 0.05BaTiO₃-PMNT and 0.10BaTiO₃- PMNT at room temperature were measured to be ~0.0084 C/m²K and ~0.0043 C/m²K, respectively. The relaxor ferroelectric properties of the BaTiO₃-PMNT system were confirmed by analyzing the plot of K_max/K versus (T-T_max)^γ. The BaTiO₃-doped MPB PMNT system showed a distinct pyroelectric performance index at room temperature, and the values were F_v ~ 0.0362 m²/C, F_d ~ 0.575×10^-4 Pa^-1/2.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.211-217
• /
• 2010

It is important to measure the mechanical properties of nanostructures because they are required to determine the lifetime and reliability of nanodevices developed for various fields. In this study, tensile tests for a multi-walled carbon nanotube (MWCNT) and a ZnO nanorod were performed in a scanning electron microscope (SEM). The force sensor was a cantilever type and was mounted in front of a nanomanipulator placed in the chamber. The nanomanipulator was controlled using a joystick and personal computer. The nanostructures dispersed on the cut area of a transmission electron microscope (TEM) grid were gripped with the force sensor by exposing an electron beam in the SEM; the tensile tests were the performed. The in situ tensile loads of the nanostructure were obtained. After the tensile test, the cross-sectional areas of the nanostructures were observed by TEM and SEM. Based on the TEM and SEM results, the elastic modulus of the MWCNT and ZnO nanorod were calculated to be 0.98 TPa and 55.85 GPa, respectively.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.355-360
• /
• 2007

Highly sensitive thick film ethanol gas sensors based on a nanocrystalline $In_{2}O_{3}$ were fabricated by painting method on alumina substrates. The crystal structure of the $In_{2}O_{3}$ powder was characterised by XRD analysis. The microstructure of the films were characterised using FE-SEM. The experimental results of the ethanol gas sensing characteristics indicated that the undoped $In_{2}O_{3}$ thick film has a high sensitivity. The sensitivity of the film heat treated at $400^{\circ}C$ for 2 hrs. was as high as 32.73 at an operating temperature of $200^{\circ}C$ to 1000 ppm ethanol gas in air.

• Journal of Sensor Science and Technology
• /
• v.16 no.6
• /
• pp.428-433
• /
• 2007

$SnO_{2}$-based thick film ethanol gas sensors were fabricated on alumina substrates and their ethanol gas sensing characteristics were investigated. The film sintered at $400^{\circ}C$ for 2 hrs. showed the highest sensitivity to ethanol gas and the sensitivity of the film to 1000 ppm ethanol gas in air was 97 % at an operating temperature of $250^{\circ}C$. The addition of $Fe_{2}O_{3}$ to $SnO_{2}$ enhanced the sensitivity by changing the type and number of surface acidic/basic sites.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.36.2-36.2
• /
• 2000