• Journal of Sensor Science and Technology
• /
• v.15 no.5
• /
• pp.309-316
• /
• 2006

The $SnO_{2}$ thin film sensors were fabricated by a thermal oxidation method. $SnO_{2}$ thin film sensors were treated in $N_{2}$ atmosphere. The sensors with $O_{2}$ treatment after $N_{2}$ treatment showed 70 % sensitivity for 1 ppm $H_{2}S$ gas, which is higher than the sensors with only $O_{2}$ treatment. The Ni metal was evaporated on Sn thin film on the $Al_{2}O_{3}$ substrate. And the sensor was heated to grow the Sn nanowire in the tube furnace with $N_{2}$ atmosphere. Sn nanowire was thermally oxidized in $O_{2}$ environments. The sensitivity of $SnO_{2}$ nanowire sensor was measured at 500 ppb $H_{2}S$ gas. The selectivity of $SnO_{2}$ nanowire sensor compared with thin film and thick film $SnO_{2}$ was measured for $H_{2}S$, CO, and $NH_{3}$ in this study.

• Journal of Powder Materials
• /
• v.22 no.3
• /
• pp.197-202
• /
• 2015

In this study, porous stainless steel (STS316L) sintered body was fabricated by powder metallurgy method and its properties such as porosity, compressive yield strength, hardness, and permeability were evaluated. 67.5Fe-17Cr- 13Ni-2.5Mo (wt%) powder was produced by a water atomization. The atomized powder was classified into size with under $45{\mu}m$ and over $180{\mu}m$, and then they were compacted with various pressures and sintered at $1210^{\circ}C$ for 1 h in a vacuum atmosphere. The porosities of sintered bodies could be obtained in range of 20~53% by controlling the compaction pressure. Compressive yield strength and hardness were achieved up to 268 MPa and 94 Shore D, respectively. Air permeability was obtained up to $79l/min{\cdot}cm^2$. As a result, mechanical properties and air permeability of the optimized porous body having a porosity of 25~40% were very superior to that of Al alloy.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.703-707
• /
• 2001

The effects of chromium addition on the catalytic activity of Raney nickel in alkaline fuel cell (AFC) have been studied. When the catalysts are prepared from various contents of chromium, the electrochemical characteristics shows the highest mass activity of 3.588 A/g. Operating temperature and electrolyte concentration of half cell were $80^{\circ}C$ and 6N KOH, respectively. With the addition of chromium, the particle size is diminished from 12.11 $\mu\textrm{m}$ to 11.07 $\mu\textrm{m}$ and the decrease of particle size contributes to the enlargement of the specific surface area from 0.653 $\m^2$/g to 0.685$\m^2$/g. The residual aluminium contents of Raney nickel surface are considerably influenced by the particle size and chromium acts as sintering inhibitor.

• Journal of the Korean Chemical Society
• /
• v.18 no.3
• /
• pp.180-188
• /
• 1974

Adsorption mechanism of alkyl aldehydes, acetaldehyde, acrolein, and crotonaldehyde on cations supported by layer silicates was studied by means of IR spectroscopy and X-ray. An analysis of four characteristic split bands in the region of $1720∼1580㎝^{-1}$ was made. The carbonyl stretching band which shifted about $130㎝^{-1}$ to lower frequencies was observed only for $Ni^{2+}$ and Al^{3+}$ but slightly with $Ca^{2+}$ at high sample temperature and was attributed to >C=O…M complex formation. A sharp band which appeared as a shoulder at 1722 for acetaldehyde and 1690 for acrolein and crotonaldehyde was responsible for the interaction of carbonyl with surface hydroxyl. The second broad band which appeared at about 1710~1660 was responsible for hydrogen bonding between carbonyl oxygen and cationic hydroxyl group. The third band which appeared at about 1640~1660 was attributed to induced >C=C< double bond due to the strong carbonyl interaction. This was supported by the interlamellar spacings obtained by X-ray diffractometry.

• Journal of Korean Society on Water Environment
• /
• v.31 no.3
• /
• pp.304-312
• /
• 2015

In this study, we tried to determine the vertical variation of sediment structure and geochemical characteristics, core sediment was collected in the Nakdong River midstream on August, 2014. Core sediment mainly composed of sand (51.48%) and silt (46.21%) and coarsing upward changed from sM to mS facies. IL and TOC were decreased from lower to upper layer. C/N ratio was lower than 10 so the organic matters were originated from underwater creatures and C/S ratio was decreased from lower to upper layer. Heavy metal (Al, Fe, Zn, Cr, Pb, Ni, Cu, Cd) content were decreased from lower to upper layer and seriously polluted condition is not. These results are thought to be due to the effect of natural and anthropogenic in the fluctuation of flow.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.77.1-77.1
• /
• 2013

Atomic layer deposition (ALD) is known for its self-limiting reaction, which offers atomic-level controllability of the growth of thin films for a wide range of applications. The self-limiting mechanism leads to very useful properties, such as excellent uniformity over a large area and superior conformality on complex structures. These unique features of ALD provide promising opportunities for future electronics. Although the ALD of Al2O3 film (using trimethyl-aluminum and water as a metal precursor and oxygen source, respectively) can be regarded as a representative example of an ideal ALD based on the completely self-limiting reaction, there are many cases deviating from the ideal ALD reaction in recently developed ALD processes. The nonconventional aspects of the ALD reactions may strongly influence the various properties of the functional materials grown by ALD, and the lack of comprehension of these aspects has made ALD difficult to control. In this respect, several dominant factors that complicate ALD reactions, including the types of metal precursors, non-metal precursors (oxygen sources or reducing agents), and substrates, will be discussed in this presentation. Several functional materials for future electronics, such as higher-k dielectrics (TiO2, SrTiO3) for DRAM application, and resistive switching materials (NiO) for RRAM application, will be addressed in this talk. Unwanted supply of oxygen atoms from the substrate or other component oxide to the incoming precursors during the precursor pulse step, and outward diffusion of substrate atoms to the growing film surface even during the steady-state growth influenced the growth, crystal structure, and properties of the various films.

• Korean Journal of Organic Agriculture
• /
• v.7 no.1
• /
• pp.147-159
• /
• 1998

In order to study the effects of chemical fertilizer and organic fertilizer on the toxic mineral content in the absence or presence of the wood extraction, the lettuce an experiment of fatal 20 treatments was conducted far a peried of 10 weeks. The results obtained from the experiment are summarized as follows; 1. The mineral contents of the lettuce in the wood extraction-treated group and the wood extraction non-treated group showed no conspicious differenves. 2. These are no prominent differences in the mineal contents(Chromium, Nickel, Lead, and Aluminium) in the lettuce between the organic fertifized group and the lettuce raised in the chemical fertilized group. 3. Mercury was not detected in all samples of lettuces raised in all treatments.4. Cadmium contents in the lettuce samples were increased as the amount of organic fertilizer was increased from 25% to 100%.

• Journal of Food Hygiene and Safety
• /
• v.36 no.3
• /
• pp.264-270
• /
• 2021

In this study we investigated the elution level of lead (Pb), cadmium (Cd), arsenic (As), zinc (Zn), nickel (Ni), antimony (Sb), germanium (Ge), aluminum (Al) and hexavalent chromium (Cr⁶⁺) from 69 home-cooking utensils into a food stimulants. The results of migration testing according to the Korea standards and specifications for utensils, containers and packages showed values the allowable migrantion limits. Al was detected in all 7 utensil materials with the average concentration ranging from 0.002-5.989 mg/L. According to the migration conditions for (180℃, 30 min), the average concentration of Al in paper was 7.2 times higher than 25℃, 10 min (P<0.05). The results of migration testing at 180℃, 30 min were also below the allowable migrantion limits. When comparing with the provisional tolerable weekly intake (PTWI) of Al, the estimated weekly intakes (EWI) accounted for 0.000-0.045% for Al.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.5
• /
• pp.259-268
• /
• 2005

Most of the tailings have been left without any management in their mines and have become the main source of serious environmental problems in nearby groundwater, stream and cultivated lands. To compare fractionation and potential mobility of heavy metals in tailings and paddy soils near abandoned 10-metalliferous mines in Korea, the distribution and chemical fractions of heavy metal and their mobility in relation to chemical compositions were investigated. The pollution index of heavy metal in mine tailing calculated with the permissible levels were in the order Cheongyang>Dogok>Beutdeun>Baegwoul mine, which were considered sufficient to raise environmental problems. The rates of 0.1M-HCl extractable Cd, Cu, Pb, Zn, and Ni to total content in paddy soils were 49.1, 50.7, 26.8, 18.4 and 2.9%, respectively, and their rates of heavy metals in paddy soils were higher than that of mine tailing. Dominant chemical forms of heavy metals in tailings were sulfide and residual form (63-91%), specially, the exchangeable portion of Cd (21%) was relatively higher than that of other metals in paddy soils. The mobility factor of heavy metals in tailings and paddy soils was in the order Cd>Zn>Cu>Pb, and the mobility factor in tailing varied considerably among the mines. The potential mobility of heavy metals in tailings showed significant positive correlation with water-soluble $Al^{3+}$ and $Fe^{3+}$ contents, while in paddy soils, it correlated negatively with soil pH values.

• Economic and Environmental Geology
• /
• v.30 no.6
• /
• pp.553-566
• /
• 1997

Origin, behavior and enrichment of environmental toxic elements from the Deokpyeong area were investigated on the basis of major, trace and rare earth element geochemistry. Coaly metapelites of the Deokpyeong area are subdivided into grey phyllite, dark grey phyllite, coaly slate and black slate, which are interbedded along the Ogcheon Supergroup. The coaly slate had been mined for coal, but mining is closed. The coaly and black slates are lower contents of $SiO_2$ and $Al_2O_3$, and higher contents of LOI, CaO, $Na_2O$ and BaO as compared with the phyllitic rocks. Rare earth elements are highly enriched in the coaly and black slate. Average compositions (ppm) of minor and/or environmental toxic elements in the coaly and black slate are revealed as As=127, Ba=30,163, Cd=18, Cr=740, Cu=84, Mo=378, Pb=43, Sb=12, Se=44, U=144, V=8,147 and Zn=292, which are extremely high concentrations than those in the NASC compositions. Major elements (average enrichment index; 5.34) in the coaly metapelites are mostly depleted, excepting $P_2O_5$ and BaO, normalized by NASC. Rare earth elements (average enrichment index; 1.48) are enriched in the coaly slate. On the basis of NASC, minor and/or environmental toxic elements in the coaly metapelites were strongly enriched of all the elements with the exception of Co, Cs, Ni and Sr. Average enrichment index of trace elements in coaly metapelite is 31.51 (coaly slate; 51.94 and black slate; 15.46). Especially, enrichment index of potentially toxic elements (As, Ba, Cr, Cu, Mo, Ni, Sb, Se, U, V and Zn) of the rock is 46.10 (grey phyllite; 7.15, dark grey phyllite; 4.77, coaly slate; 88.96 and black slate; 22.11). These coal formations were deposited in basin of boundary between terrestrial and marine environments deduced to carbon, sulfur (C/S=2.2 to 275.7), trace and rare earth elements characteristics. Irregular behavior and dispersion between major, minor and rare earth elements of those metapelites indicates a variable source materials, incomplete mixing of differential source and/or reequilibrium of diagenesis and metamorphism.