• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.64-67
• /
• 2002

The Physical and magnetic properties such as microstructure, permeability and power loss of Ni-Zn ferrite with composition of $Ni_{0.8}Zn_{0.2}Fe_2O_4$, were investigated as the function of $Bi_2O_3$ and CaO contents. The power loss increased in proportion to the amount of $Bi_2O_3$ up to 0.3 wt% but it decreased over than 0.3 wt% addition. The highest permeability of 134 was obtained to the specimen added 1.0 wt% $Bi_2O_3$ since $Bi_2O_3$ contents were strongly dominant to grain growth and size than that of CaO. $Bi_2O_3$ liquid phase created during sintering process promoted sintering and grain growth so that grain size and permeability increased compared to that of the specimens which were sintered with free-additive and CaO. Also, lots of pores existed in the specimen which was added $Bi_2O_3$ wt% with the biggest grain size.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.117-117
• /
• 2001

• Journal of Hydrogen and New Energy
• /
• v.16 no.2
• /
• pp.136-141
• /
• 2005

Li-doped NiO was synthesized by molten salt method. $LiNO_3$-LiOH flux was used as a source for Li doping. $NiCl_2$ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5:1 to 30:1 during the synthetic procedure and the Li doping amount of synthesized materials were found between 0.086-0.190 as a Li ion to Ni ion ratio. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies, however the lattice parameter decreased from 0.41769nm in pure NiO to 0.41271nm as Li doping amount increased. Hydrogen gas sensors were fabricated using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs $H_2$ concentration was checked up to 4% of $H_2$ in air (as higher concentrations above 4.65% are explosive in air) using Li doped NiO of Li ion/Ni ion=0.111 as the sensor material. The response time T90 and the recovery time RT90 were less than 25 sec. There was minimum interference of other gases and hence $H_2$ gas can easily be detected.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.7
• /
• pp.650-654
• /
• 2006

[ $LiNi_{0.4}Mn_{0.3}Co_{0.3}O_2$ ] cathode material was synthesized by a mixed hydroxide method. Structural characterization was carried out using X-ray diffraction studies. Electrochemical studies were performed by assembling 2032 coin cells with lithium metal as an anode. DSC (Differential scanning calorimetry) data showed that exothermic reactions of $LiNi_{0.4}Mn_{0.3}Co_{0.3}O_2$ charged to 4.3 V versus Li started at high temperatures$(280\sim390^{\circ}C)$. The cell of $LiNi_{0.4}Mn_{0.3}Co_{0.3}O_2$ mixed cathode delivered a discharge capacity of 150 mAh/g at a 0.2 C rate. The capacity of the cell decreased with the current rate and a useful capacity of 134 mAh/g was obtained at a 2 C rate. The reversible capacity after 100th cycles was 126 mAh/g when a cell was cycled at a current rate of 0.5 C in $2.8\sim4.3V$.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.548-551
• /
• 1995

The effect of Cu substitution on the properties of NiZn ferrites sintered at low temperature with composition is investigated. The densification of NiCuZn ferrite in dependent upon Cu content in the composition of (N/sub 0.5-x/Cu/sub x/ Zn/sub 0.5/O)(Fe/sub 2/O/sub 3/)/sub 0.98/. Electrical resistivity is maximum at x=0.2. Dispersion characteristics of complex permeability of (Ni/sub 0.5-x/ Cu/sub x/Zn/sub 0.5/O)(Fe/sub 2/O/sub 3)/sub 0.98/ is observed above x=0.3 and relaxation frequency increases with higher temperature. The magnetic loss of NiCuZn ferrite is occurred above the Cu content x=0.3 at a low frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.65-67
• /
• 1990

In this study, (0.80-x)Pb($Mg_{1/3}Nb_{2/3}$)$O_3$-$PbTiO_3$-Pb($Ni_\frac{1}{2}W_\frac{1}{2}$)$O_3$ 0.05$\leq$x$\leq$0.20) ceramics were fabricated by the mixed oxide method, the sintering temperature and time were 950∼1200[$^{\circ}C$], 2[hr], respectively. The dielectric and structural properties with composition and sintering temperature were investigated for the application as multilayer ceramic capacitors. Dielectric constant of 0.70PMN-0.2PT-0.10PNW composition with repeated calcination was increased rapidly. Increasing the Pb($Mg_{1/3}Nb_{2/3}$)$O_3$-$PbTiO_3$-Pb($Ni_\frac{1}{2}W_\frac{1}{2}$)$O_3$ contents from 0.05 to 0.20 [mol], phase transition temperature was shifted from 68 to 2[$^{\circ}C$] and dielectric constant was decreased while sintered density was increased. In the specimens containing 0.10, 0.15[mol] of PNW, dielectri constants at room temperature were exhibited the highest values 11199, 10114, respectively. Resistivity of specimens were $10^{10}$ ∼ $10^{12}$($\Omega$.m) and there was no dependence on sintering temperature and composition.

• Journal of the Korean Ceramic Society
• /
• v.20 no.4
• /
• pp.315-323
• /
• 1983

Effect of NiO and $MnO_2$ addtivies on the dielectric piezoelectrics and polarization-reversal properties of $(Pb_{0.936} La_{0.064})$$(Zr_{0.60}Ti_{0.40})O_3$ ceramics have been investigated. The specimens were prepared by the mixed oxide techni-que and atmosphere sintering method. The room temperature X-ray diffraction studies show that perfect perovskite solution with tetragonal structure was obtained from PLZT and its additives. The dielectric constant and dissipation factor decreased with the addition of both NiO and $MnO_2$ The Curie of Curie temperature was not observed but they displayed broadened maxima. The planar coupling factor was improved by addition of NiO and also increased with increasing sintering time carried out at 105$0^{\circ}C$ Addition of $MnO_2$ yielded a markedly high mechanical quality factor. The space-charge field decreased with the addition of NiO but increased with the addition of $MnO_2$ The planar coupling factor and space-charge field showed same dependence on the additivies. The tetragonality Curie temperature and planar coupling factor of $(Pb_{0.936} La_{0.064})$$(Zr_{0.60}Ti_{0.40})O_3$ were higher than those of $(Pb_{0.936} La_{0.064})$$(Zr_{0.568}NU_{0.032}Ti_{0.40})_{0.984}O_3$ but the grain size lattic parameter dielectric constant dissipation factor mechanical quality factor and space-charge field of the former were lower than those of the latter.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.1912-1920
• /
• 2011

The $SnO_2$ with a particle size of about 300 nm instead of Ni is used in this study to overcome rapid catalytic deactivation by the formation of a $NiAl_2O_4$ spinal structure on the conventional Ni/${\gamma}$-$Al_2O_3$ catalyst and simultaneously impregnated the catalyst with potassium (K). The $SnO_2-K_2O$ impregnated Zeolite Y catalyst ($SnO_2-K_2O$/ZY) exhibited significantly higher ethanol reforming reactivity that that achieved with $SnO_2$ 100 and $SnO_2$ 30 wt %/ZY catalysts. The main products from ethanol steam reforming (ESR) over the $SnO_2$-$K_2O$/ZY catalyst were $H_2$, $CO_2$, and $CH_4$, with no evidence of any CO molecule formation. The $H_2$ production and ethanol conversion were maximized at 89% and 100%, respectively, over $SnO_2$ 30 wt %-$K_2O$ 3.0 wt %/ZY at 600 $^{\circ}C$ for 1 h at a $CH_3CH_2OH:H_2O$ ratio of 1:1 and a gas hourly space velocity (GHSV) of 12,700 $h^{-1}$. No catalytic deactivation occurred for up to 73 h. This result is attributable to the easier and weaker of reduction of Sn components and acidities over $SnO_2-K_2O$/ZY catalyst, respectively, than those of Ni/${\gamma}$-$Al_2O_3$ catalysts.

• Journal of Hydrogen and New Energy
• /
• v.21 no.6
• /
• pp.500-506
• /
• 2010

The metal monolith catalyst coated with 15wt% Ni/$MgAl_2O_4$ is applied to the natural gas steam reforming for hydrogen production. To address the improvement of adherence between metal monolith and catalyst coating layer, the pre-calcination temperature as well as the coating conditions of $Al_2O_3$ sol are optimized. When the Fe-Cr alloy monolith is pre-calcined at $900^{\circ}C$ for 6 h, $Al_2O_3$ layer was formed uniformly on the entire surface of the metal substrate. It is seen that the formation of $Al_2O_3$ layer on the monolith surface is essential for the uniform coating of $Al_2O_3$ sol onto the monolith substrate. The monolith catalyst coated with 10wt% $Al_2O_3$ sol shows high $CH_4$ conversion and good thermal stability as compared with the monolith catalyst without $Al_2O_3$ sol coating under severe reaction conditions with high GHSV of 30,000 $h^{-1}$ at $700^{\circ}C$. In addition, the metal monolith catalyst shows higher catalytic activity and better thermal conductivity than 15wt% Ni/$MgAl_2O_4$ pellet catalyst.

• Bulletin of the Korean Chemical Society
• /
• v.9 no.5
• /
• pp.283-288
• /
• 1988

The titled properties on reduction of the perovskite $LaBO_3$ (B = Fe, Co, Ni) have been investigated by means of temperature-programmed reduction, isothermal reduction and X-ray diffraction methods. Nominal composition of $LaFeO_{3.18},\;LaCoO_{3.00}\;and\;LaNiO_{2.92}$ are determined. Reduction reaction of these mixed oxides differed according to B-site transition metal and thermal stability on reduction decreased as following order: $LaFeO_{3.18}$ > $LaCoO_{3.00}$ > $LaNiO_{2.92}$. From the results of isothermal reaction, kinetics on reduction of the perovskite has been discussed in detail.