• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2288-2292
• /
• 2007

The catalytic activities of nickel-based catalysts were estimated for oxidizing acetaldehyde of VOCs exhausted from industrial facilities. The catalysts were prepared by sol-gel methods of SiO2 and SiO2-TiO2 as a xerogel followed by impregnating Al2O3 powder with the nickel nitrate precursor. The crystalline structure and catalytic properties for the catalysts were investigated by use of BET surface area, X-ray diffraction (XRD), Xray photoelectron spectroscopy (XPS) and temperature programmed reduction (TPR) techniques. These results show that nickel oxide is transformed to NiAl2O4 spinel structure at the calcination temperature of 400 °C in response to the steps with after- and co-impregnation of Al2O3 powder in sol-gel process. The NiAl2O4 could suppress the oxidation reaction of acetaldehyde by catalysts. The NiO is better dispersed on SiO2-TiO2/Al2O3 support than SiO2/Al2O3 and SiO2-TiO2-Al2O3 supports. From the testing results of catalytic activities for oxidation of acetaldehyde, Catalysts showed a big difference in conversion efficiencies with the way of the preparation of catalysts and the loading weight of nickel. The catalyst of 8 wt.% Ni/TiO2-SiO2/Al2O3 showed the best conversion efficiency on acetaldehyde oxidation with 100% conversion efficiency at 350 °C.

• The Korean Journal of Ceramics
• /
• v.2 no.3
• /
• pp.162-166
• /
• 1996

The effects of NiO addition on the microstructure and microwave dielectric properties of ($Zr_{08}Sn_{02}$)$TiO_4$ (ZST) were investigated. With the NiO addition, a higher density of ZST ceramics than 95% of the theoretical values has been obtained in the sintering temperature range of 1400 to 150$0^{\circ}C$. Energy dispersive X-ray spectrometry (EDS) analysis of sintered specimen shows the presence of second phase at grain boundaries, which is considered to be $NiTiO_3$. Dielectric constant of the specimen is found to increase linearly with density. Q-values and TC$_r$ decrease with increasing NiO content. The variation of dielectric properties with NiO content is discussed in terms of the second phase. The ZST ceramics with 0.25 wt% NiO showed ${\varepsilon}_{\gamma}$=38, Q=7000 at GHz and TC$\gamma$=-0.5 ppm/$^{\circ}C$, comparable with the values obtained by the previous investigations.

• Electrical & Electronic Materials
• /
• v.9 no.10
• /
• pp.991-1000
• /
• 1996

PbTiO$_{3}$-PbZrO$_{3}$-Pb(Ni$_{1}$3/Nb$_{2}$3/O$_{3}$) (PZT-PNN) thin films were prepared from corresponding metal organics partially stabilized with diethanolamine by the sol-gel spin coating method. Each mol ratio of PT:PZ:PNN solutions were #1(50:40:10), #2(50:30:20), #3(45:35:20), #4(40:40:20), #5(40:50:10), #6(35:45:20) and #7(30:50:20) respectively. The spin-coated PZT-PNN films were heat-treated at 350.deg. C for decomposition of residual organics, and were sintered from 450.deg. C to 750.deg. C for crystallization. The substrates, such as Pt and Pt/TiN/Ti/TiN/Si were used for the spin coating of PZT PNN films. The perovskite phase was observed in the PZT-PNN films heat-treated at 500.deg. C. The crystalline of the PZT-PNN films was optimized at the sintering of 700.deg. C. By the result of AES analysis, It is confirmed that the films of TiN/Ti/TiN was a good diffusion barrier and that co-diffusion into the each films was not observed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.3
• /
• pp.245-251
• /
• 2000

Dielectric properties, piezoelectric properties and mechanical properties of NiO-doped Pb($(Ni_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3$ ceramics were investigated. Powders, prepared by columbite precursor method, were cold pressed and sintered at temperature ranging from $1100^{\circ}C$ to $1250^{\circ}C$. Dielectric constant and piezoelectric constant increased with amount of NiO up to 1 mol% and then decreased with further addition of NiO. It seems that NiO acts as a sintering aid at the sintering temperatures of $1150^{\circ}C$. When the samples were sintered at temperature above $1200^{\circ}C$, however, both dielectric constant and electromechanical coupling factor decreased and mechanical quality coefficient increased with addition of NiO. Hardness and fracture toughness of PNN-PT-PZ increased with addition of NiO up to 1 mol%, and then decreased slightly with further addition of NiO. These results showed that dielectric properties, piezoelectric properties and mechanical properties of PNN-PT-PZ system seemed to be closely related with microstructural factors such as grain size, bulk density and the amount of second phase.

• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1260-1266
• /
• 1996

The effects of SiO2 MnO2 and sintering atmospheres (O2, N2) on the piezoelectric properties and densification behaviors of Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 were investigated. The addition of SiO2 to the system enhanced the rate of densification but supressed the rate of grain growth. On the other hand the addition of MnO2 to the system did not nearly affect the rate of densification but increased slightly the rate of grain growth The densification of Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 containing of SiO2 or MnO2 was promoted with increasing the partial pressure of O2. The relative dielectric constant ($\varepsilon$r) and piezoelectric constant (d33) of Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 containing of SiO2 or MnO2 sintered under O2 atmosphere were higher than under N2 atmosphere. Whereas the mechanical quality factor (Qm) of specimens sintered under O2 atmosphere were lower than under N2 atmosphere. Thus the sintering atmosphere of O2 and N2 in Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 containing of SiO2 or MnO2 acted as donor and acceptor respectively. As the amount of SiO2 increased the relative dielectric constant ($\varepsilon$r) and piezoelectric constant (d33) of Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 but the mechanical quality factor (Qm) did not nearly change, In the case of the addition of MnO2 to the system the relative dielectric constant ($\varepsilon$r) and piezoelectric constant (d33) of Pb0.98Cd0.02Zr0.36Ti0.39Ni0.083Nb0.167O3 sintered under O2 atmosphere decreased rapidly with increasing the amount of MnO2 but they were unchanged with increasing the amount of MnO2 under N2 sintering atmosphere. Therefore the differences of the relative dielect-ric constant ($\varepsilon$r) and piezoelectric constant (d33) due to sintering atmosphere were diminished as the amount of MnO2 increased.

• Journal of the Korean Chemical Society
• /
• v.25 no.4
• /
• pp.236-245
• /
• 1981

The electrical conductivities of oxidized pure and Ni-doped $SrTiO_3$ single crystals were measured as a function of the oxygen partial pressure($Po_2$) at temperature from 700 to $1200^{\circ}C$ and $Po_2$ of $10^{-8}$ to $10^{-1}$ atm. Plots of log ${\sigma}$ vs. 1/T at constant $Po_2$ were found to be linear, and the activation energies obtained from the slopes of these plots have an average value of 1.34 eV for oxidized pure and 1.06 eV for oxidized Ni-doped $SrTiO_3$ single crystals at $Po_2$'s between $10^{-8}$ to $10^{-1}$ atm. The log ${\sigma}$ vs. log $Po_2$ curves at constant temperature were found to be linear with an average slope of ${\frac{-1}{5.6}}\;{\sim}\;{\frac{-1}{6.2}}$ in the $Po_2$ ranges. From the agreement between experimental and theoretically predicted values for the electrical conductivity dependences on $Po_2$, an oxygen vacancy defect model was found applicable to oxidized pure and Ni-doped $SrTiO_3$ single crystals over the temperature range, 700~$1200^{\circ}C$. Conduction mechanisms were proposed to explain the dependences of electrical conductivity on temperature and $Po_2$.

• Korean Chemical Engineering Research
• /
• v.57 no.5
• /
• pp.714-722
• /
• 2019

Catalysts were prepared by using incipient wetness impregnation method with 17 wt% Ni on a support ($SiO_2-Y_2O_3$, $Al_2O_3$, $SiO_2-ZrO_2$, $SiO_2$, $TiO_2$, MgO) and the catalytic activity in the reductive amination of ethanol with ammonia in the presence of hydrogen was compared and evaluated. The catalysts used before and after the reaction were characterized using X-ray diffraction, nitrogen adsorption, ethanol-temperature programmed desorption (EtOH-TPD), isopropanol-temperature programmed desorption (IPA-TPD), and hydrogen chemisorption etc. In the case of preparing $ZrO_2$ and $Y_2O_3$ supports, the small amount of Si dissolution from the Pyrex reactor surface provoked the formation of mixed oxides $SiO_2-ZrO_2$ and $SiO_2-Y_2O_3$. Among the catalysts used, $Ni/SiO_2-Y_2O_3$ catalyst showed the best activity, and this good activity was closely related to the highest nickel dispersion, and low desorption temperature in EtOH-TPD and IPA-TPD. The low catalytic activity on Ni/MgO catalysts showed low activity due to the formation of NiO-MgO solid-solutions. In the case of $Ni/TiO_2$, the reactivity was low due to the low nickel metal phase due to strong metal-support interaction. In the case of using a support as $SiO_2-Y_2O_3$, $Al_2O_3$, $SiO_2-ZrO_2$, and $SiO_2$, the selectivities of ethylamines and acetonitrile were not significantly different at similar ethanol conversion.

• Journal of the Korean Ceramic Society
• /
• v.48 no.3
• /
• pp.211-216
• /
• 2011

Nickel oxide-doped ACF and $TiO_2$ composites (NiO/ACF/$TiO_2$) were prepared by a sol-gel method. The composite obtained was characterized by BET surface area measurements, X-ray diffraction, transmission electron microscopy and energy dispersive X-ray analysis. A methylene blue (MB) solution under visible light irradiation was used to determine their photocatalytic activity. Excellent photocatalytic degradation of the MB solution was observed using the $TiO_2$, Ti-ACF and NiO/ACF/$TiO_2$ composite under visible light.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.11a
• /
• pp.141-141
• /
• 1994

• Korean Journal of Materials Research
• /
• v.33 no.8
• /
• pp.330-336
• /
• 2023

The effects of Ni²⁺ substitution for Mg²⁺-sites on the microwave dielectric properties of (Mg_1-xNi_x)(Ti_0.95(Mg_1/3Ta_2/3)_0.05)O₃ (0.01 ≤ x ≤ 0.05) (MNTMT) ceramics were investigated. MNTMT ceramics were prepared by conventional solid-state reaction. When the MgO / TiO₂ ratio was changed from 1.00 to 1.02, MgTi₂O₅ was detected as a secondary phase along with the MgTiO₃ main phase in the MNTMT specimens sintered at 1,400 ℃ for 4h. For the MNTMT specimens with MgO / TiO₂ = 1.07 sintered at 1,400 ℃ for 4h, a single phase of MgTiO₃ with an ilmenite structure was obtained from the entire range of compositions. The relative density of all the specimens sintered at 1,400 ℃ for 4h was higher than 95 %. The quality factor (Qf) of the sintered specimens depended strongly on the degree of covalency of the specimens, and the sintered specimens with x = 0.01 showed the maximum Qf value of 489,400 GHz. The dielectric constant (K) decreased with increasing Ni²⁺ content because Ni²⁺ had a lower dielectric polarizability (1.23ų) than Mg²⁺ (1.32ų). As Ni²⁺ content increased, the temperature coefficient of resonant frequency (TCF) improved, from -55.56 to -21.85 ppm/℃, due to the increase in tolerance factor (t) and the lower dielectric constant (K).