• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.838-840
• /
• 1998

$BiNbO_4$ ceramics with 0.06wt% CuO, 0.1wt% $V_{2}O_{5}$ sintered at $900^{\circ}C$. The strip line chip filter has been design and fabricated by screen printing with silver electrode after tape casting. The characteristics of the fabricated filters were compared with the simulated results. In the strip line chip filter, insertion loss value of band pass width was 3.65[dB] and return loss was 8.9[dB] and center frequency was similar that simulation results.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.13-19
• /
• 2009

A 440MHz wireless and passive surface acoustic wave (SAW) based chemical sensor was developed on a $41^{\circ}YX\;LiNbO_3$ piezoelectric substrate for simultaneous measurement of $CO_2$ gas and relative humidity (RH) using a reflective delay line pattern as the sensor element. The reflective delay line is composed of an interdigital transducer (IDT) and several shorted grating reflectors. A Teflon AF 2400 and a hydrophilic $SiO_2$ layer were used as $CO_2$ and water vapor sensitive films. The coupling of mode (COM) modeling was conducted to determine optimal device parameters prior to fabrication. According to simulation results, the device was fabricated and then wirelessly measured using the network analyzer. The measured reflective coefficient $S_{11}$ in the time domain showed high signal/noise (S/N) ratio, small signal attenuation, and few spurious peaks. In the $CO_2$ and humidity testing, high sensitivity ($2^{\circ}/ppm$ for $CO_2$ detection and $7.45^{\circ}/%$RH for humidity sensing), good linearity and repeatability were observed in the $CO_2$ concentration ranges of $75{\sim}375ppm$ and humidity levels of $20{\sim}80%$RH. Temperature and humidity compensations were also investigated during the sensitivity evaluation process.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.404-408
• /
• 2010

The effects of high energy ball-milling (HEBM) on the sintering behavior and piezoelectric properties of 0.1 wt% $Li_2CO_3$ doped 0.8Pb($Mg_{1/3}Nb_{2/3}$)$O_3$-0.2Pb($Zr_{0.475}Ti_{0.525}$)$O_3$ (PMN-PZT) ceramics were investigated. It was found that HEBM treatment was quite effective to reduce the average particle size down to 300 nm, leading to increased density as well as enhanced piezoelectric properties of a sintered specimen even though prolonged HEBM resulted in unwanted secondary phases that caused a degradation of piezoelectric properties. The dielectric constant ($\varepsilon_r$), piezoelectric coupling factor ($k_p$) and piezoelectric constant $d_{33}$ of 0.1 wt% $Li_2CO_3$ doped PMN-PZT ceramics prepared via HEBM for 10 h reached 2040, 0.68 and 554 pC/N, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1853-1855
• /
• 2005

본 논문에서는 카메라폰용 광학줌(Optical zooming)과 자동초점조절장치(Auto Focusing, AF)에 쓰일 초음파모터를 제작하였다. 초음파모터의 제작 및 시뮬레이션은 유한요소해석 프로그램인 ATILA 5.2.1(Magsoft)를 사용하여 디자인설계에 따른 구동특성을 고찰하였고 세자된 초음파모터는 한쪽 면이 없는 사자형의 탄성체를 제작하였으며 탄성체의 양쪽 다리에 각각 압전체를 부착하였다. 또한 압전세라믹의 조성은 $0.9Pb(Zr_{0.51}Ti_{0.49})O_3$-$0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$의 조성으로 설계하였고 시편의 제조는 7-layer로 적층하였다. 제작된 압전세라믹의 치수는 $6*2*0.35mm^3$ (길이*폭*두께)로 제작하였다. 또한 탄성체의 외형치수는 $10*10*2mm^3$ 제작하였으며 두께를 각각 0.3[mm], 0.5[mm], 0.8[mm]으로 변화시키며 제작하였다. 두께가 0.8[mm]인 경우 공진주파수 60.5[kHz]를 나타내었으며 초음파모터의 압전세라믹에 인가전압이 증가함에 따라 회전속도와 모터에 흐르는 전류는 증가하였다. 인가전압이 40[Vpp], 공진주파수는 60.5[kHz]일때 무게추를 달고 그때의 토크 및 효율을 측정하였다. 회전 속도는 토크가 증가함에 따라 거의 선형적으로 감소하였으며 효율은 토크에 따라 증가하다가 토크가 약 20(mNmm)일 때 약 28[%]로 최대치를 나타내었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.921-925
• /
• 2000

Characteristics of Pb(Mg, Nb)O$_3$-Pb(Zr, Ti)O$_3$system thick films fabricated by a screen printing method were investigated. The buffer layer were coated with various thickness of Ag-Pd by screen printing to investigate the effect as a diffusion barrier and deposited Pt as a electrode by sputtering on Ag-Pb layer. The printed thick films were burned out at 650$\^{C}$ and sintered at 950$\^{C}$ in O$_2$condition for each 20, 60min after printing with 350mesh screen. The thickness of piezoelectric thick film was 15∼20㎛ and Ag-Pb layer acted as a diffusion barrier above 3㎛ thickness. The PMN-PZT thick films were screen printed on Pt/Ag-Pb(6m) and sintered by 2nd step (650$\^{C}$/20min and 950$\^{C}$/1h) using paste mixed PMN-PZT and binder in the ratio of 70:30, and the remnant polarization of thick film was 9.1$\mu$C/㎠ in this conditions.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.2
• /
• pp.1-4
• /
• 1976

In this paper, temperature dependence of the resonant frequency of thickness shear mode in X cut plate of $LiN_bO_3$ is theoretically analyzed. An a result of this analysis, theoretical value -78.43${\times}10^{-5}/^{\circ}C$ of the temperature coefficient of resonant frequency is obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.331-334
• /
• 1998

The solid solutions of the Pb(Sc$\_$0.5/Nb$\_$0.5/)$\_$0.57/Ti$\_$0.43/O$_3$ system were prepared. In the PSNT system, it had been known that two-phase region between the rhombohedral and tetragonal phases was observed between 0.425 of PT at room temperature. In this paper, Fe$_2$O$_3$-doped 0.57PSN-0.43PT composition was prepared by conventional method. The dielectric and strain properties were examined using an computerized measuring apparatus, and the resonance characteristics were measured using an impedance gain phase analyzer. We got the data of dielectric constant, dielectric loss, piezoelectric coefficient, piezoelectric voltage coefficient, frequency constant strain constant mechanical quality factor and electromechanical coupling factor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.251-254
• /
• 2000

This paper was to measure the structure, electric characteristics of 0.05Pb($(Al_{0.5}Nb_{0.5})$) - 0.95Pb$(Zr_{0.52}Ti_{0.48})O_3$ ceramics dopped with Cr+Fe. The results of this paper were gotten such as follows; The dielectric constants were decreased with Cr+Fe. The dielectric loss was minimum value of 1.008[%], dopped with Cr+Fe O.9[wt%] at 1200[$^{\circ}C$], In case of sintering at 1150[$^{\circ}C$], electromechanical factodkp) was maximum value of kp 42.73[%], at Cr+Fe 0.9[wt%]. The mechanical quality factor(Qm) was maximum value at Cr+Fe 1.2 [wt%], Also, in case of dopped with Cr+Fe, it make a improvement in temperature coefficient of resonant frequency at 0.3[wt%], 1150[$^{\circ}C$].

• Journal of the Korean institute of surface engineering
• /
• v.31 no.5
• /
• pp.245-250
• /
• 1998

There is clear pressing need to reduce bias field(Ha,) used on linear magenetomechanical resonator tag by at least a factor of two to allow low-bias operation near the frequency minimum since reducing Ha causes a dramatic increase in well depth, which implies increased stability. However, this makes it more difficult to maintain tight frequncy specs. It can be solved by a reduction of magnetomechanical coupling(k). We determined from an equivalent circuit model that optimal reduced, k, is near 0.3 Also, We determiend the material properties($lambda_s$, :saturated magenetostriction, $M_s$, and,$H_a$) that give k=0.3. From these evaluations, we suggested that on optimal comosition with adequate mathrial properties is $Fe_{55}Co_{15}Cr_6Nb_2B_{18}Si_4$.

• Journal of the Korean Ceramic Society
• /
• v.45 no.9
• /
• pp.524-530
• /
• 2008

Anti-Reflective (AR) thin film coatings of $SiO_2$ (n= 1.48) and $TiO_2$ (n=2.17) were deposited by ion-beam assisted deposition (IBAD) with End-Hall ion source and conventional electron beam (e-beam) evaporation to investigate the effect of deposition method on the refractive indicies (n) of the fIlms. Green-light generation using a GaAs laser diode was achieved via excitation of the second harmonic. The latter resulted from the transmission of the fundamental guided-mode wave of 1064 nm through periodically poled $LiNbO_3$. Large differences in the refractive indicies of each of the layers in the multilayer coating may improve AR performance. IBAD of $SiO_2$ reduced its refractive index from 1.45 to 1.34 at 1064 nm. Conversely, e-beam evaporation of $TiO_2$ increased its refractive index from 1.80 to 2.11. In addition, no fluctuations in absorption at the wavelength of 1064 nm were found. The results suggest that films prepared by different deposition methods can increase the effectiveness of multilayer AR coatings.