• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.70-73
• /
• 1989

(1-x-y)Pb($Zn_{1/3}Nb_{2/3})O_3-Ba(Zn_{1/3}Nb_{2/3})O_3-PbTiO_3(0.12{\leq}x{\leq}0.21, 0.24{\leq}y{\leq}0.33$) ternary compound ceramics were fabricated by the mixed oxide method. The sintering temperature and time were 1050 [$^{\circ}C$], 2[hr]. Morphotropic phase boundary region was chosen for the composition. 0.55 PZN-0.21 BZN-0.24 PT specimen had the highest value of relative dielectric constants, 5353. The curie temperature of specimens were increased linearly with PT content. Near the morphotropic phase boundary, electro-mechanical coupoling factor and mechanical quality factor of the specimens had the highest values.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.925-928
• /
• 2011

Perovskite niobates and tantalates have been placed on a short list of functional materials for future technologies. This article was investigated ferroelectric materials $Ag(Ta,Nb)O_3$ thick film. In this study, we have fabricated the $Ag(Ta,Nb)O_3$ thick film on the $Al_2O_3$ substrates by screen printing method. The $Ag(Ta,Nb)O_3$ thick film were fabricated by the mixed oxide method. The sintering temperature and time were 1,150$^{\circ}C$, 2 hr. The electrical properties of $Ag(Ta,Nb)O_3$ thick film were investigated at 30~100$^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.38 no.1
• /
• pp.56-60
• /
• 2001

90.24 mol% ZrO$_2$-5.31 mol% $Y_2$O$_3$-4.45 mol% Nb$_2$O$_{5}$ 조성의 (Y,Nb)-TZP와 (Y,Nb)-TZP/Al$_2$O$_3$복합체를 155$0^{\circ}C$~1$600^{\circ}C$에서 1~2시간 소결하여 제조하였다. 시편의 결함에 대한 저항성을 조사하기 위하여 R-curve, Weibull modulus, slow crack growth 변수 등을 조사하였다. 실험결과, (Y,Nb)-TZP와 (Y,Nb)-TZP/Al$_2$O$_3$복합체 모두 상용 3Y-TZP 보다 우수한 결함 저항성이 관찰되었다. (Y,Nb)-TZP/Al$_2$O$_3$복합체의 결함 저항성은 $Al_2$O$_3$첨가에 의한 결정립 가교 인화, 분산강화, R-curve 효과에 의한 것으로 추정된다.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.645-651
• /
• 1997

Tetragonal zirconia polycrystals (TZPs) doped with $Y_{2}O_{3}$ and $Nb_{2}O_{5}$ were prepared by the conventional sintering to enhance fracture toughness and phase stability of TZPs without controlling the grain size. TZP composites were obtained by adding the transformable TZP to the non-transformable TZP in wt%. The monolithic tetragonal $ZrO_2$, same as the composite composition containing 15 wt% transformable TZP, sintered at $1550^{\circ}C$ for 10h in air, exhibited the fracture toughness of 9$MPam^{1/2}$ and no low-and high-temperature degradation at temperatures in the range of 220 to $1000^{\circ}C$ for 100h in air. The corresponding single composition was 90.24 mol% $ZrO_2$-5.31 mol% $Y_{2}O_{3}$-4.75 mol% $Nb_{2}O_{5}$. The microstructure observation revealed that the t-$ZrO_2$ grains grew grandually with sintering time and no microcraking and twinning were observed.

• Journal of the Korean Ceramic Society
• /
• v.24 no.6
• /
• pp.579-585
• /
• 1987

The effects of flux KCl and dopant Nb2O5 on the PTCR characteristics of BaTiO3 prepared by molten salt synthesis method have been investigated. As the amount of dopant Nb2O5 is over the solubility limit in BaTiO3, the room-temperature resistivity increases, and the PTCR effect and the grain size decrease. The variation of the amount of flux KCl slightly influences on the room-temperature resistivity, PTCR effect and grain size in Nb2O5 doped BaTiO3, but BaTiO3 ceramics prepared by the method of molten salt synthesis show larger PTCR effect than those of conventional calcining of mixed oxides.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.6
• /
• pp.466-474
• /
• 2021

[011] poled ternary Pb(In_1/2Nb_1/2)O₃-Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PIN-PMN-PT) single crystals have been investigated for active materials for acoustic transducers because of their high piezoelectric properties in both shear and transverse modes. In order to use [011] poled PIN-PMN-PT single crystals for acoustic transducers, the characterization of full-matrix material properties is required. In this study, full sets of compliance, dielectric, and piezoelectric constants of [011] poled rhombohedral PIN-PMN-PT were measured by a resonance method. Dimensions and geometries of 12 samples were proposed for measuring 17 independent material constants of [011] poled rhombohedral PIN-PMN-PT single crystals. Two sets of samples with different PT concentrations, 0.24PIN-0.49PMN-0.27PT and 0.24PIN-0.46PMN-0.30PT, were fabricated and their material properties were measured. Measured impedance spectra and simulated impedance spectra of the samples were compared to check the accuracy of the measurements.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.17-24
• /
• 1996

Pb(Mg1/3Nb2/3)O3 powder with high purity chemical homogeniety and reactivity was prepared by solvent eva-poration of common solution. The common solution was fabricated using a Pb(NO3)2 Mg(NO)3 and NB solution which was prepared by dissolving NbC in H2O2 acquous solution. In precusor powder prepared by solvent evaporation method the synthetic temperature of Pb(Mg1/3 Nb2/3)O3 phase was lowered. And the formation of homogeneous Pb(Mg1/3Nb2/3)O3 phase was enhanced but the formation of pyrochlore phase was reduced. The dielectric constant of PMN ceramics from the synthesized powder was found to increase with both sintering temperature and excess MgO and subsequent analysis of the microstructures confirmed that this was due to an increase in grain size. The grain size dependence is explained as a consequence of low-permittivity grain boundaries.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.559-562
• /
• 2011

In this study, the effect of $Nb_2O_5$ and sintering time on the positive temperature of coefficient of resistivity (PTCR) behavior of lead free $Ba_{0.99}(Bi_{0.5}Na_{0.5})_{0.01}TiO_3$ (BBNT) ceramics were investigated in order to fabricate a PTC thermistor with high $T_c$ temperature more than $140^{\circ}C$. In particular, BBNT ceramic doped with 0.1mol% $Nb_2O_5$ and sintered at $1350^{\circ}C$ for 4 h has significantly increased Curie temperature ($T_c$) of about $200^{\circ}C$, showed good PTCR behavior of room-temperature resistivity ($\rho_{rt}$) of $40{\Omega}{\cdot}cm$, a high $\rho_{max}/\rho_{min}$ ratio of $43.78{\times}10^3$ and a large resistivity temperature factor (${\alpha}$) of 16.1%/$^{\circ}C$. With increasing addition of $Nb_2O_5$ content, the $\rho_{rt}$ decreased to a minimum value of $40\;{\Omega}cm$ at 0.1mol% $Nb_2O_5$ and the $\rho_{rt}$ increased for x value over 0.1 mol%.

• Journal of the Korean Ceramic Society
• /
• v.24 no.3
• /
• pp.263-269
• /
• 1987

It is investigated that the determination of the correlation between the change of microstructure and electrical properties. Yttria is added to the compositiojn of rhombohedral region in Pb(Mg1/3Nb2./3)O3-PbTiO3-PbZrO3 ternary system. Average grian size, lattice parameters and distribution of yttrium are characterized by XRD, SEM and EDS. Electrical properties are determined by measurement of Curie temperature, piezoelectric properties and hysteresis loops. The results are as follows; 1. Both lattice parameters, a and ${\alpha}$, are changed by addition of yttria to the composition of rhomboheadral region in Pb(Mg1/3Nb2./3)O3-PbTiO3-PbZrO3 ternary system and Curie temperature is proportional to the values at (90-${\alpha}$).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.285-289
• /
• 2011

In this study, lead-free $(K_{0.5}Na_{0.5+X})(Nb_{0.96}Sb_{0.04})O_3+0.2mol%La_2O_3+1.2mol%$ $K_4CuNb_8O_{23}$ (X= 0~0.025) ceramics were fabricated by normal sintering method at $1060^{\circ}C$ for 5 h. Microstructures, piezoelectric and dielectric properties of specimens were investigated with special emphasis in the influence of Na excess addition. The grain size of specimen was slightly decreased with increasing Na content. In the 2 [mol%] Na excess addition of NKNS ceramics, density, electromechanical coupling factor, piezoelectric constant and electromechancal quality factor of specimen were found to reach the optimum values of 4.25 [$g/cm^3$], 0.4357, 154.43 [pC/N] and 580, respectively.