• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.4
• /
• pp.479-485
• /
• 2017

Objective: The effects of particle size of processed barley grain, enzyme addition and microwave treatment on in vitro dry matter (DM) disappearance (DMD), gas production and fermentation pH were investigated for feedlot cattle. Methods: Rumen fluid from four fistulated feedlot cattle fed a diet of 860 dry-rolled barley grain, 90 maize silage and 50 supplement g/kg DM was used as inoculum in 3 batch culture in vitro studies. In Experiment 1, dry-rolled barley and barley ground through a 1-, 2-, or 4-mm screen were used to obtain four substrates differing in particle size. In Experiment 2, cellulase enzyme (ENZ) from Acremonium cellulolyticus Y-94 was added to dry-rolled and ground barley (2-mm) at 0, 0.1, 0.5, 1, and 2 mg/g, while Experiment 3 examined the interactions between microwaving (0, 30, and 60 s microwaving) and ENZ addition (0, 1, and 2 mg/g) using dry-rolled barley and 2-mm ground barley. Results: In Experiment 1, decreasing particle size increased DMD and gas production, and decreased fermentation pH (p<0.01). The DMD (g/kg DM) of the dry-rolled barley after 24 h incubation was considerably lower (p<0.05) than that of the ground barley (119.1 dry-rolled barley versus 284.8 for 4-mm, 341.7 for 2-mm; and 358.6 for 1-mm). In Experiment 2, addition of ENZ to dry-rolled barley increased DMD (p<0.01) and tended to increase (p = 0.09) gas production and decreased (p<0.01) fermentation pH, but these variables were not affected by ENZ addition to ground barley. In Experiment 3, there were no interactions between microwaving and ENZ addition after microwaving for any of the variables. Microwaving had minimal effects (except decreased fermentation pH), but consistent with Experiment 2, ENZ addition increased (p<0.01) DMD and gas production, and decreased (p<0.05) fermentation pH of dry-rolled barley, but not ground barley. Conclusion: We conclude that cellulase enzymes can be used to increase the rumen disappearance of barley grain when it is coarsely processed as in the case of dry-rolled barley. However, microwaving of barley grain offered no further improvements in ruminal fermentation of barley grain.

• Journal of Hydrogen and New Energy
• /
• v.8 no.2
• /
• pp.91-97
• /
• 1997

The goals of this research are to understand the $NO_x$ emission in direct injected diesel engine with premixed hydrogen fuel. Hydrogen fuel was supplied into the test engine through the intake pipe. Amount of hydrogen-supplemented fuel was 70 percent basis heating value of the total fuel. The effects of intake air temperature on $NO_x$ emission were studied. The intake air temperature was controlled by flow rate of liquid nitrogen. The major conclusions of this work include : (i) the tested engine was run without backfire under 70 percent hydrogen fuel supplemented. (ii) radicals of nitrogen gas in the intake pipe were increased by 30 percent and cylinder gas temperature was decreased by 24 percent as the intake air temperature were changed from $23^{\circ}C$ to $0^{\circ}C$ ; and (iii) $NO_x$ emission per unit heating value of supplied fuel was decreased by 45 percent with same decrease of intake air temperature.

• Korean Journal of Materials Research
• /
• v.10 no.11
• /
• pp.778-783
• /
• 2000

Effects of the $Al_2$O$_3$surface protective layer, deposited on the SnO$_2$sensing layer by aerosol flame deposition (AFD) method, on the sensing properties of SnO$_2$thin film ags sensors were investigated.Effects of Pt doping to the $Al_2$O$_3$surface protective layer on the selectivity of CH$_4$ gas were also investigated. 0.3$\mu\textrm{m}$ thick SnO$_2$thin sensing layers on Pt electrodes were prepared by R.F. magnetron sputtering with R.F. power of 50 W, at working pressure of 4mTorr, and at 20$0^{\circ}C$ for 30 min. $Al_2$O$_3$surface protective layers on SnO$_2$layers were prepared by AFD using a diluted aluminum nitrade (Al(NO$_3$).9$H_2O$) solution. The sensitivity of CO gas in the SnO$_2$gas sensor with an $Al_2$O$_3$surface protective layer was significantly decreased. But that of CH$_4$gas remained almost same with pure SnO$_2$gas sensor. This result shows that the selectivity of CH$_4$gas is increased because of the $Al_2$O$_3$surface protective layer. In the case of SnO$_2$gas sensors with Pt-doped $Al_2$O$_3$surface protective layers, low sensing property to CO gas and high sensing property to CH$_4$were observed. This results in the increasing of selectivity of CH$_4$gas selectivity are discussed.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.2
• /
• pp.331-341
• /
• 2018

Hazardous air pollutants(HAPs) in the atmosphere are regulated as major air pollutants in Korea by the Air Pollution Control Act. In order to manage and control HAPs, accurate standards, which are traceable to the International System of Units(SI), are required. In this study, primary standard gas mixtures(PSMs) of volatile organic compounds(VOCs) which are specified as HAPs were developed at $1{\mu}mol/mol$ levels. The selected fourteen VOCs include Benzene, Toluene, Ethylbenzene, m-Xylene, Styrene, o-Xylene, Chloroform, 1,1,2-Trichloroethane, Trichloroethylene, Tetrachloroethylene, 1,1-Dichloroethane, Carbon tetrachloride, 1,3-Butadiene, and Dichloromethane. The HAPs PSMs were gravimetrically prepared in aluminum cylinders and their consistency was verified within the relative expanded uncertainty of 0.71% (k=2). Potential adsorption loss onto the internal surface of cylinders was estimated by cylinder-to-cylinder division method. No adsorption loss was observed within the uncerainty of 0.53%. The long-term stability of the HAPs PSMs was evaluated comparing with freshly prepared HAPs PSMs. The HAPs PSMs were stable for one year within the uncertainty of 0.38%. The final uncertainty of the PSMs was determined by combining the preparation uncertainty, verification uncertainty, and stability uncertainty. Finally, traceable and stable HAPs PSMs at $1{\mu}mol/mol$ levels were developed with the uncertainty of less than 0.76% in high-pressure aluminum cylinders.

• Fire Science and Engineering
• /
• v.33 no.3
• /
• pp.1-8
• /
• 2019

The international standard for FT-IR gas analysis of fire effluents in ISO 5660-1 cone calorimeter has been being developed in ISO TC 92. A comparison of the round-robin test of WD 21397 was conducted with six participating laboratories in 2018. The test specimens were PMMA, rigid PU foam board, and PVC flooring. The measurement quantities were the time-to-ignition, peak heat release rate, total heat release, and effective heat of combustion for a cone calorimeter test and peak gas concentration, gas generation, and gas yield for FT-IR gas analysis. No outliers were identified. For the cone calorimeter quantities, the repeatability and reproducibility were 1.5% and 9.8%, respectively. For FT-IR gas analysis, the repeatability and reproducibility was 12.9% and 27.9%, respectively.

• Design & Manufacturing
• /
• v.18 no.3
• /
• pp.71-80
• /
• 2024

Sink marks are a common defect that occurs due to differences in shrinkage in areas with significant thickness variations in injection-molded parts. In this paper, we investigated the reduction of sink marks and the improvement of gas venting in injection molding processes using External Gas Injection (EGI). A mold was designed with considerations for EGI core pins, O-ring grooves to prevent gas leakage, and ejector-pin sealing. The sink marks were then examined through a series of experiments. When the delay time for injecting compressed air was set to 2.2 seconds, the depth of the sink marks was minimized. However, when the delay time was either too short or too long, the depth of the sink marks increased. There was almost no difference in the depth of the sink marks at discharge pressures of 30 and 50 bar of compressed air, but the sink marks were significantly reduced at a discharge pressure of 70 bar. Under the conditions of a 2.2-second delay time and a supply pressure of 70 bar, the smallest depth, 0.594 ㎛, was observed when the supply time was between 6 and 7 seconds. This represents a reduction of approximately 94% compared to the sink mark depth of 10.078 ㎛ observed with conventional injection molding. To verify the gas venting effect of compressed air injection, an experiment was conducted using non-dried PC. The silver streaks that appeared on the exterior of the molded part were completely eliminated when the air supply pressure was set to 20 bar. This indicates that by injecting compressed air into the mold cavity before injecting the resin, the appearance quality of the injection-molded part can be improved without the need to dry the resin in advance.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.5
• /
• pp.541-549
• /
• 2003

A basic experimental study was conducted in order to find the optimum combustion control technology to decrease the thermal NO$_{x}$, by applying the catalytic combustion method with natural gas. NO$_{x}$ emission increased with increasing space velocity due to temperature rising in the furnace. In order to overcome the low resistance to high temperature, secondary air was supplied to the CST combustor. The following secondary fuel formed combustible mixture in part, which resulted in steep increase of the exiting temperature of the 2nd catalyst bed. It led to the more generator of NO$_{x}$, 30∼60% of the 1 st catalyst bed. It might be due to the potential increase of thermal NO$_{x}$.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.1
• /
• pp.80-85
• /
• 2006

Ninety six crossbred pigs (Landrace${\times}$Yorkshire${\times}$Duroc) were used to determine the effects of essential oils (Fresta F $Conc^{(R)}$) supplementation on growth performance, immune response and fecal noxious gas of weaned pigs. Treatments were 1) NC (negative control; basal diet without antibiotics), 2) PC [positive control; basal diet+CSP (CTC+Sulfathiazole+Penicillin) 0.1%], 3) NCF (basal diet+Fresta F $Conc^{(R)}$ 0.03%) and 4) PCF [basal diet+CSP (CTC+Sulfathiazole+Penicillin) 0.1%+Fresta F $Conc^{(R)}$ 0.02%]. From d 0 to 14, ADFI was increased in pigs fed PCF diet (p<0.05). From d 14 to 28, pigs fed PCF diet had greater ADG and ADFI than pigs fed NC diet (p<0.05). From d 28 to 49, ADG and ADFI in pigs fed PCF diet were higher than in pigs fed NC diet (p<0.05). Through the entire experimental period, ADG and ADFI in pigs fed PCF diet were the highest compared to pigs fed NC and PC diets (p<0.05). There was no significant difference in fecal consistency score among the treatments (p>0.05). No statistical differences (p>0.05) were found in red blood cells (RBC) counts, white blood cells (WBC) counts, lymphocyte counts, total protein and albumin. Serum IgG concentration of PCF treatment was greater than that of other treatments (p<0.05). From d 0 to 14, there was no significant difference in digestibility of dry matter and nitrogen among the treatments (p>0.05). From d 14 to 28, digestibility of dry matter in pigs fed PC, NCF and PCF diets was higher than that of pigs fed NC diet (p<0.05) and treatments with added essential oils were higher than other diets on digestibility of nitrogen (p<0.05). Also, from d 28 to 49, digestibility of nitrogen in pigs fed PCF diet was the highest among others (p<0.05). On d 14 and 28, no statistical differences (p>0.05) were found in volatile fatty acid (VFA), ammonia nitrogen ($NH_3$-N) and hydrogen sulfide ($H_2S$) concentrations among treatments. On d 49, there was no significant difference in VFA concentration among the treatments (p>0.05). $NH_3$-N concentration in pigs fed PCF diet was lower than in pigs fed other diets (p<0.05). $H_2S$ concentration in pigs fed diets with added essential oils was lower than others. In conclusion, the results suggest that the dietary addition of essential oils and antibiotics into diets for weanling pigs improved growth performance, IgG concentration and nitrogen digestibility and decreased noxious gas concentration. Essential oils can be used to partly replace antibiotics in diets for weaned pigs without negative affects on growth performance.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.58.1-58.1
• /
• 2014

Energetic gas outflows from active galactic nuclei (AGNs) may have a crucial role in galaxy evolution. In this contribution, we present a census of ionized gas outflows using a large sample (~23,000) of local (z < 0.1) type-2 AGNs selected from the Sloan Digital Sky Survey DR 7. By measuring the velocity offset of narrow emission lines, i.e., [O III] ${\lambda}5007$ and the Balmer lines, with respect to the systemic velocity measured from the stellar absorption lines, we find ~47% of AGNs showing an [O III] line-of-sight velocity offset ${\geq}20km\;s-1$. The fraction in type-2 AGNs is similar to that in type-1 AGNs after considering the projection effect. AGNs with larger [O III] velocity offsets, in particular with no or weak $H{\alpha}$ velocity offsets, tend to have higher Eddington ratios, implying that the [O III] velocity offset is related to on-going black hole activity. Also, we find the different distributions of the host galaxy inclination between the AGNs with blueshifted [O III] and the AGNs with redshifted [O III], supporting the model of biconical outflow with dust obscuration. Meanwhile, for ~3% of AGNs, [O III] and $H{\alpha}$ exhibit comparable large velocity offsets, suggesting a more complex gas kinematics than decelerating outflows in the narrow-line region.

• Journal of Industrial Technology
• /
• v.6
• /
• pp.19-31
• /
• 1986

The residence time distribution of liquid flow in a 4.0cm diameter column packed with porous $Al_2O_3$ spheres of 0.37cm diameter were measured with pulse injections of a tracer under cocurrent trickling flow conditions. The mean residence time of liquid flow and liquid hold-up calculated by the transient curve of tracer were unaffected by gas flow rates under experimental ranges of liquid flow rates from 2.4 to $4.5(kg/m^2\;sec)$ and gas flow rates from 0 to $0.13(kg/m^2\;sec)$. The axial dispersion coefficient of liquid stream and apparent diffusivity of tracer in a micropore of solid particle were estimated from the response curve of tracer. The calculated Peclet No. were increased in ranges of 68-to 82 with a increasing of liquid mass velocity, and the external effective contacting efficiency between liquid and solid which can be expressed. by $(D_i)_{app}/D_i$ varied in ranges of 0.54 to 0.68 depending on the liquid flow rates. The gas to liquid(water) volumetric mass transfer coefficient were determined from desorption experiments with oxygen at $25^{\circ}C$ and 1 atm. The measured mass transfer coefficients were increased with liquid flow rates and the effect of gas flow rates on the mass transfer coefficient was insignificant.