• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제4권4호
• /
• pp.201-208
• /
• 2000

The reduction of NO by hydrocarbons was investigated over Cu/Al$_2$O$_3$catalysts using a stainless steel flow reactor under highly oxidising diesel exhaust conditions(up to 15%). Three different Cu loadings(1,5 and 10wt.%) on an $Al_2$O$_3$support were prepared and characterized using spectroscopic techniques. The catalytic activity tests show that different Cu loadings as well as temperature, oxygen, and hydrocarbon concentration levels significantly influence the NO reduction. Increasing Cu loadings up to 5 and 10wt.% decreases the catalytic activities for NO reduction due to the formation of a bulk crystalline CuO phase, as observed from XRD and SEM images. In particular, the visualization of the copper dispersion on the surface using the SEM-BEI technique provides information on the extent of copper saturation, particle size, and the effects on NO reduction. However, the lower Cu loading(1 wt.%) increases the catalytic activity with a temperature window of 720-810K, thereby favoring the formation of well dispersed isolated Cu species, e.g. Cu(sup)2+ ions, which is related to selective NO reduction. The effects of other reaction parameters, such as oxygen, the hydrocarbon level and type, and byproduct emissions are further discussed.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.125-137
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• 자원환경지질
• /
• 제30권6호
• /
• pp.553-566
• /
• 1997

Origin, behavior and enrichment of environmental toxic elements from the Deokpyeong area were investigated on the basis of major, trace and rare earth element geochemistry. Coaly metapelites of the Deokpyeong area are subdivided into grey phyllite, dark grey phyllite, coaly slate and black slate, which are interbedded along the Ogcheon Supergroup. The coaly slate had been mined for coal, but mining is closed. The coaly and black slates are lower contents of $SiO_2$ and $Al_2O_3$, and higher contents of LOI, CaO, $Na_2O$ and BaO as compared with the phyllitic rocks. Rare earth elements are highly enriched in the coaly and black slate. Average compositions (ppm) of minor and/or environmental toxic elements in the coaly and black slate are revealed as As=127, Ba=30,163, Cd=18, Cr=740, Cu=84, Mo=378, Pb=43, Sb=12, Se=44, U=144, V=8,147 and Zn=292, which are extremely high concentrations than those in the NASC compositions. Major elements (average enrichment index; 5.34) in the coaly metapelites are mostly depleted, excepting $P_2O_5$ and BaO, normalized by NASC. Rare earth elements (average enrichment index; 1.48) are enriched in the coaly slate. On the basis of NASC, minor and/or environmental toxic elements in the coaly metapelites were strongly enriched of all the elements with the exception of Co, Cs, Ni and Sr. Average enrichment index of trace elements in coaly metapelite is 31.51 (coaly slate; 51.94 and black slate; 15.46). Especially, enrichment index of potentially toxic elements (As, Ba, Cr, Cu, Mo, Ni, Sb, Se, U, V and Zn) of the rock is 46.10 (grey phyllite; 7.15, dark grey phyllite; 4.77, coaly slate; 88.96 and black slate; 22.11). These coal formations were deposited in basin of boundary between terrestrial and marine environments deduced to carbon, sulfur (C/S=2.2 to 275.7), trace and rare earth elements characteristics. Irregular behavior and dispersion between major, minor and rare earth elements of those metapelites indicates a variable source materials, incomplete mixing of differential source and/or reequilibrium of diagenesis and metamorphism.

• 자원환경지질
• /
• 제9권3호
• /
• pp.143-156
• /
• 1976

The Cretaceous metal ore deposits in the Gyeongsang basin of Gyeongsangbuk-do are characterized by the formation of metallogenic provinces which show zonal distribution pattern around Yeonil province where pneumatolytic type is dominated and hydrothermal type are distributed in the order of decreasing temperature type outward. Some Cretaceous granitic rocks include zoned alkali feldspars which reflect rapid variation of $H_2O$ during emplacement and crystallization of the water-saturated granitic magma. The ore deposits are considered to be originated from upward transportation of ore solution from the excess of water exhausted from uprising magma, which seems to be intimately related to the fact that the majority of the ore deposits in Daegu area are cummulated around the granites including zoned alkali feldspars. In order to collect geochemical data necessary for geochemical exploration in the study area, certain trace elements were chosen as pathfinders from monzonite and soil in the vicinity of Dalsung Tungsten Mine by studying the dispersion patterns of trace elements: Ba and Sr show trends to decrease toward ore deposit while Cu, Pb, and Mo increase. Around mining area there are distributed apparently Equisetum arvense Linne and Mentha sachinensis Kudo which may be used as index plants. In the viewpoint of geologic structure, the trends of the ore veins in contact aureole around the Palgongsan granite body correspond with the pre- and syn- plutonism joint pattern in hornfels in the area.

• 한국실내디자인학회논문집
• /
• 제18권3호
• /
• pp.102-113
• /
• 2009

The SARS virus began to appear and spread in North America and Southeast Asia in the early 2000' s, infecting and harming many people. In the process of examining the causes for the virus, studies on the airborne SARS virus and the way it spread were carried out mainly in the medical field. In the field of architecture, studies were done on the diffusion of air pollutants in buildings using gases such as $CO_2$, $N_2O$, or $SF_6$, but research on virus diffusion was limited. There were also explanations of only the diffusion process without accurate information and discussion on virus characteristics. The aim of this study is to analyze the physical characteristics of airborne virus, consider the possibility of using coupled analysis model and tracer gas for analyzing virus diffusion in building space and, based on reports of how the infection spread in a hospital where SARS patients were discovered, analyze infection risk using tracer gas density and also diffusion patterns according to the location, shape, and volume of supply diffusers and exhaust grilles. This paper can provide standards and logical principles for evaluating various alternatives for making decisions on vertical or horizontal ward placement, air supply and exhaust installation and air volumes in medium or high story medical facilities.