• Journal of the Korean institute of surface engineering
• /
• v.37 no.5
• /
• pp.296-300
• /
• 2004

The defects of partial denture frameworks are mainly shrinkage porosity, inclusions, micro-crack, particles from investment, and dendritic structure. In order to investigate a good casting condition of partial denture frameworks, the three casting alloys and casting methods were used and detected casting defects were analyzed by using electrochemical methods. Three casting alloys (63Co-27Cr-5.5Mo, 63Ni-16Cr, 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting (Kerr, USA), high frequency induction casting (Jelenko Eagle, USA), vacuum pressure casting (Bego, Germany). The casting temperature was $1,380^{\circ}C$ (63Co-27Cr-5.5Mo and 63Ni-16Cr) and $1,420^{\circ}C$ (63Co-30Cr-5Mo). The casting morphologies were analyzed using FE-SEM and EDX. The corrosion test of the dendritic structure was performed through potentiodynamic method in 0.9% NaCl solutions at $36.5^{\circ}C$ and corrosion surface was observed using SEM. The defects of partial denture frameworks improved in the order of centrifugal casting, high frequency induction casting, and vacuum pressure casting method, especially, pore defects were found at part of clasp in the case of centrifugal casting method. The structure of casting showed dendritic structure for three casting alloys. In the 63Co-27Cr-5.5Mo and 63Co-30Cr-5Mo, $\alpha$-Co and $\varepsilon$-Co phases were identified at matrix and $${\gamma}$-Ni_2$Cr second phase were shown in 63Ni-16Cr. Also, the corrosion resistance of cast structure increased in the order of vacuum pressure casting, high frequency induction casting, and centrifugal casting method.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.11
• /
• pp.1211-1216
• /
• 1998

Bis(diethyldithiocarbamato)ioxomolybdenum(VI), cis-MoO2(S2CNEt2)2, 1, reacted with chlorotrimethylsilane (Me33SiCl) to give a seven-coordinate, pentagonal bipyramidal complex MoOC12(S2CN]Et2)2, 3, in which the oxo ligand is trans to the chloride ligand and the two chloride ligands are mutually cis. The monooxo molybdenum complex bis(diethyidithiocarbamato)oxomolybdenum(IV), MoO(S2CNEt2)2, 2, reacted with phenyl isocyanate (PhNCO) to give an Mo dimer MO2{μ-N(CONPh)Ph}(μ-NPh)(NPh)2(S2CNEt2)2, 4, which contains an Mo-Mo bond, two diethyldithiocarbamato ligands, two terminal imido (NPh) ligands, and two bridging hnido (NPh) ligands. One of the two bridging NPh ligands seemed to have been attacked by the electrophilic phenyl isocyanate carbon, which suggests that the bridging imido NPh ligand is more nucleophilic than the terminal one. Crystallographic data for 3: monoclinic space group P21/c, a=8.908(l) Å, b=17.509(3) Å, c=12.683(2) Å, β=110.15(1)°, Z=4, R(wR2)=0.0611(0.1385). Crystallographic data for 4-THF: orthorhombic space group P212121, a=17.932(4) Å, b=22.715(5) Å, c=11.802(3) Å, Z=4, R(wR2)=0.0585(0.1286).

• Bulletin of the Korean Chemical Society
• /
• v.30 no.9
• /
• pp.1927-1928
• /
• 2009

• Journal of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.495-500
• /
• 1988

The trans effect has been interpreted for a series of trans-[PtNH$_3$Cl$_2$2L] (L = H$_2$O, NH$_3$, Cl$^-$, Br$^-$, I$^-$, CH$_3$ and PH$_3$) and PtCl$_4^{-2}$ by means of our modified-EHMO method. The calculation shows that reduced overlap population(ROP) of Pt-N bond trans to L is decreased with a better trans director. That is, the trans effect has been found to be enhanced with a better trans director. Accordingly, it could be interpreted quantum chemically the trans effect for a general trans-PtTL$_2$X complex.

• Korean Journal of Crystallography
• /
• v.4 no.1
• /
• pp.1-5
• /
• 1993

The crystal structure of N-(2'-chloro-4'-vitrophenyl)-5-chlorosalicylamide( Niclosamide ) monohydrate has been determined from 1976 sig- nificant independent reflections collected on an automated CAD4 diffractometer using graphitemonochromated Mo-Ka radiation. The crystal is monoclinic, space group P211c, with unit cell dimensions, a=11.331 (3), b=16.964(2), c=7.347(4)A , P =98.20(3)° and Z=4 at T=293k. The structure was solved by direct method using seminvariants of ggg Parity group and refined by the full-matrix least-square method, resulting model with reliability factor, R=0.046. The feature of the molecule show planar structure in parallel to the ab crystal plane.

• Korean Journal of Metals and Materials
• /
• v.50 no.9
• /
• pp.653-657
• /
• 2012

In this study, a molybdenum disilicide ($MoSi_2$) coating process was investigated by hydrogen reduction and Si-pack cementation. At first, the metallic Mo coating was carried out by hydrogen reduction of $MoO_3$ powder at $750^{\circ}C$ for various holding times (1, 2, 3 h) in hydrogen atmosphere. A $4.3{\mu}m$ thick metallic molybdenum thin film was formed at 3 h. $MoSi_2$ was obtained by Si-pack cementation on molybdenum thin film through hydrogen reduction processing. It was carried out using $Si:Al_2O_3:NH_4Cl=5:92:3$ (wt%) packs at $900^{\circ}C$ for various holding times (30, 60, 90 min) in Ar atmosphere. When the holding time was 90 min, a $MoSi_2$ layer was coated successfully and a $15.4{\mu}m$ thickness was observed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.576-584
• /
• 2020

The extruder screw material is mainly SKD11, but the recent development of synthetic resins have increased the occurrence of chemical corrosion and wear. To solve this issue, high chromium cast iron is needed because of its good abrasion resistance and corrosion resistance, but its use is avoided because of its poor machinability. In this study, to improve the machinability of high chrome cast iron, 0, 0.5, 1.0, 1.5% of nickel, which has excellent workability, was added to high chromium cast iron with a composition of Fe-23Cr-2.5C-1.2Si-1.08Mn-0.48Mo-0.3V, and annealed after casting. Subsequently, the effect of nickel on the machinability and corrosion resistance was analyzed using a turning test and coin polarization test, and compared with SKD11. After casting using a high-frequency vacuum induction furnace, the annealing treatment was performed at 750 ℃ for five hours and then reheated at 1100 ℃ for five hours. A turning test after annealing at 750 ℃ showed that the machinability was improved remarkably when the nickel content was over 1.0%. In the potentiodynamic polarization test in a 5% NaCl solution, the corrosion resistance decreased with increasing nickel content in the as-cast and annealing treatment. On the other hand, after reheating, the corrosion resistance was best with a 1.5% nickel content.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.109-110
• /
• 2006

We have studied the effect of C/Ti atomic ratio of TiCx (x=0.5, 0.75 and 1.0) raw powder on the properties of the Ti-Mo-WTiC sintered hard alloy. The decrease of C/Ti atomic ratio accelerated the densification in the sintering process. The hardness was remarkably improved up to 1350HV with decreasing the C/Ti atomic ratio because of increase of TiCx phase volume content and its fine dispersion. From the results of electro-chemical tests in acid and 3% NaCl solutions, it was obvious that every alloy had excellent corrosion resistance, which meant about 200 times better than that of WC-Co cemented carbide.

• KSBB Journal
• /
• v.19 no.6 s.89
• /
• pp.446-450
• /
• 2004

We investigated the effective culture conditions of anaerobic bacteria, Enterobacter cloacae YJ-1 on hydrogen production. It was cultured with 60 mL of working volume at $35^{\circ}C$, 120 rpm for 40 h. With culture time, hydrogen production and cell growth increased, but residual glucose and pH decreased. When the $2\%$ of glucose was used as single carbon source, hydrogen production was 975.1 mL/L. To enhance hydrogen productivity, mixed carbon sources of glucose and sucrose were added. The maximum hydrogen production was earned at the mixing ratio of 25:75, and it was 1319.5 mL/L. When we added 50 mM of phosphate to protect the pH drop in culture broth, hydrogen production increased 1.3 times more than that of initial concentration. The organic nitrogen sources were more effective than inorganic nitrogen for hydrogen production. Among organic nitrogen, yeast extract was the most effective and its hydrogen production was 1691.3 mL/L. Among 9 of mineral sources, Ferric citrate and $NaMoO_4$ were especially effective, and their productions were 1782.3 mL/L and 1784.8 mL/L, respectively.

• KSBB Journal
• /
• v.5 no.4
• /
• pp.355-363
• /
• 1990

Methanol-utilizing bacterium isolated from sewage samples in Seoul showed optimal temperature and pH of $33^{\circ}C$ and 7.1 for growth, respectively. The maximum specific growth rate was $0.42hr^{-1}$. The minimum medium composition was reconstituted depending on the surplus and the deficit of each component in the basal medium at steady state. The optimal composition was given as(g/l); Methanol 40, $(NH_4)_2\;SO_42, \;KH_2PO_4\;1.5, \;K_2HPO_4\;0.2, \;H_3PO_4\;0.79, \;Na_2HPO_4{\cdot}12H_2O\;0.15, \;MgSO_4{\cdot}7H_2O\;1.5, \;FeSO_4{\cdot}7H_2O\;0.034, \;MnSO_4{\cdot}4H_2O\;0.005, \;CuSO_4{\cdot}5H_2O\;0.0027, \;CaCl_2{\cdot}2H_2O\;0.25, \;ZnSO_4{\cdot}7H_2O\;0.007, \;(NH_4)_6\;Mo_7O_{24}{\cdot}4H_2O\;0.00048, \;H_3BO_3\;0.00068, \;CoCl_2\; 0.00024$ Under the continuous culture with optimum medium the maximum cell productivity was 3.8g/1/hr at dilution rate $0.23hr^{-1}$. Maximum cell concentration and its protein content were 19.5g/l and 70% at dilution rate of $0.1hr^{-1}$, respectively.